Kaadas 20220725 Lamborghini Smart Digital Lock User Manual

: June 13, 2024
: Kaadas

Kaadas 20220725 Lamborghini Smart Digital Lock

Introduction

Dear customers, thank you for using our smart lock.
Please check the package content and read the installation instruction carefully before you install this lock, and then install the product according to the instruction.
Our company will not assume any responsibility for direct or indirect product problems, other hazards and losses if you don’t follow the instruction to install.

Important Information

Safety instruction

Read and understand all instructions before using this smart lock.
Damages caused by failure to follow instructions is not covered by the warranty.
It is recommended to use the enclosures/accessories specified by the company.
Use only alkaline batteries configured with this product.
Do not forcibly disassemble this product in order to avoid alarm sound or damage to the product.
Do not scratch the fingerprint reader with sharp objects, otherwise it may cause permanent Long-term damage.
Do not expose the product to corrosive substances, so as not to damage the outer protective layer.
Do not hang objects on the handle, so as not to affect the normal use of the door lock.
Cleaning the product, please wipe it with a soft cloth.
Do not disassemble the battery while the device is operating.
Please choose a professional engineer to install the door lock and follow the company’s standard installation instruction , and do not install it by yourself .
After the door lock is installed , please modify the default master PIN code immediately and keep the mechanical key in a safe place. Don’t disclosure PIN code to the unknown person.
When low battery alarm is triggered, please replace all the batteries in time.

Warning

Do not place battery closing to fire in case of explosion .
Do not short-circuit the two poles of the battery lead with metal objects to avoid explosion.
Do not let it happened connection of two terminals of battery lead shorted with metal objects in case of explosion.
Making sure replacement or maintenace are done by professional person authorized by Kaadas .
Your warranty may invalidate if you used accessories produced by other manufacturer or not recommended by Kaadas.

Disposal of used battery and lock

Please understand the local electronic product classification and collection system.
Please follow the local regulations and do not discard used batteries into ordinary household garbage.
Properly disposing of used products helps to avoid potential negative impacts on the environment and human health.
The battery can not be disposed of with ordinary household garbage.

Install Your Smart Lock

Package list

This Package list is for reference only, and all contents are subject to the actual packaging contents.

Front panel
(with rubber gasket)
Back panel
(with rubber gasket)
Installation template
Mortise
Strike plate
Mechanical key
Mounting plate
User card
Screw pack
User manual
warranty card
Micro fibor Wiper

Explosive view

Understanding the installation of a three-dimensional assembly drawing is beneficial to understand lock structure.
Explosive view

Front panel
M6 Connecting screw bolt
Mortise
M5 screws (4)
Back panel
Upper M6 Screw
Back cover
Springs (2)
Square shaft (2)
M5 connecting screw bolt (4)
Screws for mounting mortise (4)
Mounting Plate
Below M6 screw
Battery cover

Before installation

Check door open direction before installation

Right-out open
Right-in open
Left-out open
Left-in open

Change the direction of Latchbolt

Loosen the screw counterclockwise with an Allen wrench, then take out face plate.
Take out latchbolt and rotate 180°， then take back latchbolt.
Install back faceplate and tighten screws , then work done

Installation steps

Drill bores following the installation template and then put the mortise into the door and tighten the four mounting screws.
Note : According to the thickness of the door, select the appropriate length square shaft and connecting screw.
Install the connecting screw bolt on the front panel, and put the pressure spring and square shaft in the hole.
Pass the connectors and screw bolts through the bore on the door , and then insert the square shaft into the mortise follower of the front panel.
Finally , mounting the front panel by mounting plate.
Take out back panel and battery cover.
Insert the preesure spring and the square shaft into the hole of back panel. Then insert the front panel connector and mortise connector into the corresponding interfaces on the back panel.
The excess cable plugs back the cable holes and then tighten the screws to fix the back panel.
Install the back cover and batteries (4 pcs or 8 pcs) , then install battery cover.
Check whether each part is installed well.

Overview

Front panel

Back panel

Set Your Smart Lock

Before you set up
The system mode of the smart lock is divided into security mode and common mode, and the default system mode is a common mode. Security mode :
dual verification is required (Pin code+ fingerpringt, Pin code + card , Card+ fingerprint);
Common mode: single verification is OK (Pin code, card, fingerprint )

Security mode	Common mode
Master pin code	the master code before entering master mode

before entering master mode
User Pin code| One time pin code is not allowed to use| One time pin code is not allowed to use
User

ﬁngerprint

Note : Before setting up security mode, you have to enroll any verification methods of fingerprint,Pin code and card. user Pin code is with fake pin code function, which means you can enter any code before and after the real Pin code but it can’t exceed 32 codes.

User Number
Under master mode , when you enroll PIN code, fingerprint and card , you should enter user number.
When you need to delete single user , you can delete single user pin code according to user number .
You can fill in the user information in this table for easy management :

User number	User name	Fingrtprint	Fingrtprint	Card

Enter master mode

Touch the keypad area to wake up the keypad.
Press * twice and enter the master PIN code (default is 12345678 ) with # key to confirm.
Voice prompt: master mode.
Note : If the master pin code is default, please change to a new master pin code first.

User Settings
Add normal user

lock will encode users automatically. Users can follow the voice guide to add user pin code , fingerprint or card.

press 1 for user setting, then press 1 again to add user pin code. Enter new pin code with # confirmation. enter new pin code with # confirmation again. Voice prompt setting succeeded.

press 1 for user setting, then press 1 again to add user fingerprint . put your fingerprint on the sensor until voice prompt setting succeeded.

Press1 for user setting, then press 1 to add user card .
Put card on the reader until voice prompt: setting succeeded.

Add one-time user

Under master mode:

Press 1 for user setting , then press 2 to add one time pin code. enter new one time Pin code with # confirmation.
Enter new one time Pin code with # confirmation again .
Voice prompt setting succeeded.

Add master fingerprint

Under master mode:

Press 1 for user setting, then press 3 to add master fingerprint . put your fingerprint on the sensor until voice prompt setting succeeded.

Change master Pin code

Under master mode:

press 1 for user setting, then press 4 to change master pin code . enter new master pin code with # confirmation.
Enter new master pin code with # confirmation again .
Voice prompt setting succeeded.

Delete user

Under master mode:

Press 1 for user setting, press 5 to delete users, then press 1 to delete single user pin code , fingerprint or card.
Input the Pin code, fingerprint or card you want to delete .
Voice prompt deletion succeeded.

Press 1 for user setting, press 5 to delete users, then press 2 to delete all user pin code . Voice prompt deletion succeeded.

Press 1 for user setting, press 5 to delete users, then press 3 to delete all user fingerprint . Voice prompt deletion succeeded.

Press 1 for user setting, press 5 to delete users, then press 4 to delete all user cards . Voice prompt deletion succeeded.

Enable/Disable Dual validation

Under master mode:

Press 1 for user setting., then press 6 to enable or disable dual verification. Voice prompt setting succeeded.

Enable/Disable auto mode

Under master mode:

Press 1 for user setting , then press 7 enable or disable auto mode . Voice prompt setting succeeded , auto mode/ manual mod.

Language setting

Under master mode:

Press 2 for system setting. then press 2 for language setting.
Press 1 to select Chinese , press 2 to select English.

Extension function

Under master mode:

Press 4 for extension function. Press 1 to login network ,
press 2 to logout network.

Unlock from outdoor(Common mode

Touch the pad screen by palm to lighten keypad; then entering the enrolled PIN code with end of [#]. After voice prompt “door opened”, push or pull handle to open the door.

Place the enrolled finger properly on the fingerprint sensor area. After voice prompt “door opened”,push or pull handle to open the door.
Unlock From Outdoor

Place the enrolled card properly on the card icon area. After voice prompt “door opened”, pressing down the handle to open the door.

Note:

Under common mode, when you verify fingerprint , card or Pin code more than 5 times incorrectly , the lock will have a lockdown for 100S.
Under security mode, when you verify any two of fingerprint , card or Pin code more than 5 times incorrectly , the lock will have a lockdown for 100S.

Unlock by mechanical key

You can unlock by mechanical key if you forget pin code , the battery run out or system error occurs.

Insert the mechanical key and then rotate 180°to unlock.
If your door is right opening direction, please turn the key clockwise.
Insert the mechanical key and then rotate 180°to unlock.
If your door is left opening direction, please turn the key counterclockwise.

Auto/manual mode

Take out the battery cover , there is a A/M switch.
A represents Auto mode , in which it will automatically lock after closing door.
M represents manual mode, in which the lock will be always opened after close door.

Lock/unlock from in door

Locking button (close) press the close button to lock long press the close button to enable privacy mode.
In privacy mode , lock can be opened only by master pin code or inside.
Unlocking button（open） double press the open button to unlock
Enable/ disable the sensor of inside hande, long press open and close button together to enable/disable the sensor of inside handle.

Unlock by inside sensor handle

Inside sensor handle enabled , holding the inside handel and cover the sensor to unlock.
Inside sensor handle disabled, please press open button to unlock or enable sensor again.

Emergency Knob

When system error occurs, you can rotate the knob tp unlock Indoor /Back Panel

Volume Adjustment

when system is in voice mode , you can long press 0 button after keypad lighten to turn off voice temporarily. it will recover once keypad waked up again.
when system is in mute mode , you can long press 0 button after keypad lighten to turn on voice temporarily. It will recover once keypad waked up again.
Volume Adjustment

Doorbell

Other Functions

Restore to factory settings

If you forgot the master pin code, you can take out the battery cover then double press the Reset button till Voice prompts restored to factory setting , please modify the master pin code immediately. It means reset succeeded.
Other Functions

Emergency power supply

When the battery voltage is too low to open the lock from outside, you can use 5V power bank to charge the door lock via Micro USB port. After the door is unlocked, please replace all batteries immediately.
When battery voltage is lower than 4.8V, voice prompts “Low battery, please replace all batteries” at each unlocking. Please replace all batteries immediately, and do not mix old batteries and new batteries together in replacement.
Other Functions

System reboot

Press the reboot button to restart the lock, when the system error occurs . No user data is deleted.
Other Functions

Replace battery

When voice prompts that low battery , please change battery in time . please follow the prompt to change battery in time
Replace Battery

Extended modules (Optional)

Extended network module is reserved for smart home system, please contact kaadas for more details 。
$Extended Modules $Optional$$

www.kaadasgroup.com
Shenzhen Kaadas Intelligent Technology co.,Ltd. reserves all rights for the final interpretation for this user manual. And the mannual is subject to be changed without notice.

Logo