Kaadas K9-5W Smart Lock User Manual

Kaadas K9-5W Smart Lock

Product Information

• The smart lock is manufactured by Shenzhen Kaadas Intelligent Technology Co., Ltd. It is a high-quality lock designed for secure and convenient access to your doors.
• The lock features various functions, including fingerprint recognition, PIN code entry, and mechanical key access.
• It is important to read and understand the user manual before using the smart lock to ensure proper installation and usage.

Friendly Reminders

• Please check the package content and read the installation instructions carefully before installing the lock.
• Follow the instructions provided in the user manual for installation to avoid any product problems or hazards.
• Use only alkaline batteries specified for this product.
• Avoid disassembling the product forcefully to prevent alarm sound or damage.
• Do not scratch the fingerprint reader with sharp objects to prevent permanent damage.
• Avoid exposing the product to corrosive substances that may damage the outer protective layer.
• Do not hang objects on the handle to ensure normal use of the door lock.
• Clean the product with a soft cloth.
• Do not disassemble the battery while the device is operating.
• Have a professional engineer install the door lock according to the company’s standard installation instructions.
• Change the default master PIN code after installing the door lock and keep the mechanical key in a safe place.
• Do not disclose the PIN code to unknown persons.
• Replace all batteries when the low battery alarm is triggered.
• Do not place batteries close to the fire to prevent an explosion.
• Use only recommended accessories and comply with safety regulations when powering the product.
• Do not short-circuit the battery lead with metal objects to avoid explosion.
• Ensure replacement or maintenance is done by a professional authorized by Kaadas to avoid warranty invalidation.
• Dispose of used batteries and products according to local regulations to minimize negative impacts on the environment and human health.

Product Usage Instructions

1. Carefully unpack the package and ensure all the components are included as listed in the user manual.
2. Read the installation instructions provided in the user manual thoroughly before proceeding with the installation.
3. Follow the step-by-step instructions to install the smart lock on your door. Refer to the labeled components for easy identification.
4. After installation, modify the default master PIN code immediately to ensure security. Keep the mechanical key in a safe place.
5. To use the smart lock, you can choose from the available methods: fingerprint recognition, PIN code entry, or mechanical key access.
6. For fingerprint recognition, place your registered finger on the fingerprint reader and wait for verification. The lock will unlock if the fingerprint matches.
7. For PIN code entry, enter your assigned PIN code using the provided keypad. Press the confirmation button or follow the instructions for verification and unlocking.
8. In case of emergency or if other methods fail, use the mechanical key to manually unlock the door.
9. Ensure proper maintenance of the smart lock by regularly cleaning it with a soft cloth and avoiding any damages or scratches.
10. If the low battery alarm is triggered, replace all batteries promptly to ensure uninterrupted usage.
11. Follow all safety precautions and guidelines mentioned in the user manual to prevent any accidents or damages.

For more detailed information on other functions and features of the smart lock, please refer to the user manual available on the official website: www.kaadasgroup.com.

Friendly Reminders:

Dear customers, thank you for using our smart lock. Please check the package content and read the installation instruction carefully before you install this lock, and then install the product according to the instruction.
Our company will not assume any responsibility for direct or indirect product problems, other hazards and losses if you don’t follow the instruction to install.Thanks.

Important information

Safety instruction

• Read and understand all instructions before using this smart lock.
• Damages caused by failure to follow instructions is not covered by the warranty.
• It is recommended to use the enclosures/accessories specified by the company.
• Use only alkaline batteries configured with this product.
• Do not forcibly disassemble this product in order to avoid alarm sound or damage to the product.
• Do not scratch the fingerprint reader with sharp objects, otherwise it may cause permanent Long-term damage.
• Do not expose the product to corrosive substances, so as not to damage the outer protective layer.
• Do not hang objects on the handle, so as not to affect the normal use of the door lock.
• Cleaning the product, please wipe it with a soft cloth.
• Do not disassemble the battery while the device is operating.
• Please choose a professional engineer to install the door lock and follow the company’s standard installation instruction, and do not install it by yourself .
• After the door lock is installed, please modify the default master PIN code immediately and keep the mechanical key in a safe place.
• Don’t disclosure PIN code to the unknown person.
• When low battery alarm is triggered, please replace all the batteries in time.

Warning

• Do not place battery closing to fire in case of explosion .
• Do not use emergency power sources that do not comply with safety regulations to power this product.
• Do not short-circuit the two poles of the battery lead with metal objects to avoid explosion.
• Making sure replacement or maintenace are done by professional person authorized by Kaadas .
• Your warranty may invalidate if you used accessories produced by other manufacturer or not recommended by Kaadas.

Disposal of used battery and lock

• Please understand the local electronic product classification and collection system.
• Please follow the local regulations and do not discard used batteries into ordinary household garbage.
• Properly disposing of used products helps to avoid potential negative impacts on the environment and human health.
• The battery can not be disposed of with ordinary household garbage.

Installation

Package contents

This package list is for reference only, All package contents are subject to the actual packing contents.

Explosive view

Understanding the installation of a three-dimensional assembly drawing is beneficial to understanding the lock structure.

1. Battery cover
2. Back panel screw
3. Battery
4. Back panel
5. Square shaft
6. Front panel screw
7. Mounting plate
8. Mortise
9. Spring
10. M6 connecting screw bolt
11. Front panel
12. Rubber plug
13. M5 connecting screw bolt

Before installation

Check the door open direction before installation

Change the direction of Latchbolt

1. Loosen the screw counterclockwise with an Allen wrench, then take out the face plate.
2. Take out the latch bolt and rotate 180°, then take back the latch bolt.
3. Install back faceplate and tighten screws, then work done.

Installation steps

1. Drill bores following the installation template and then put the mortise into the door and tighten the four mounting screws.

Note: According to the thickness of the door, choose the appropriate length of the square shaft and solenoid.|
Install the connecting screw bolt on the front panel, and put the pressure spring and square shaft in the hole.

Install your smart lock

• Pass the connectors through the bore on the door , and then insert the square shaft into the mortise follower of the front panel. Finally, mounting the front panel by mounting plate.
• Note: According to the thickness of the door, choose the appropriate length of the square shaft and compression spring.
• Install compression spring and square shaft on the back panel, front panel connection cable and mortise connection cable Insert the corresponding connector on the back panel.
• Install the back panel and alkaline battery, then install the battery cover.
• Check whether each part is installed well.

Overview

Back panel

Set your smart lock

• The system of this lock can be set to enable or disable dual verification. When dual-verification is turned on, two kinds of keys (fingerprint + password, password + card, fingerprint + card) are required to pass the verification at the same time to unlock.
• close the dual-verification. only need to verify one kind of secret key to unlock.
• Security mode: needs dual verification (fingerprint + password, password + card, fingerprint + card).
• Common mode: single verification (password, fingerprint, and card can be verified).

| Security mode| Common mode
---|---|---
Master pin code| Yes

The master code before entering master mode

| Yes

Initial Password 12345678

User

pin code

| One-time password prohibited| A one-time password can be used
User fingerprint| Yes| Yes
User card| Yes| Yes
Method of entering master mode| Enter the master pin code to access| Enter the master pin code fingerprint to access

Access into master mode

1. Touch the keypad area to wake up the keypad.
2. **Press *** twice and enter the master PIN code with the # key to confirm.
3. Voice prompt : master mode.

• Note: If the Master PIN code is the initial password, You need to modify the
• Master the PIN code before you can execute other operations.

User setting

Enroll user

• When enrolling a user, the lock automatically recognizes and adds a password, fingerprint, and card, and the user directly adds the corresponding key.

In Master mode

• Press 1 to go to user Settings, press 1 again to go to Add user fingerprint, and Enroll new fingerprint, Until a voice prompt: Enrollment succeeded.”
• Press 1 to enter user Settings, press 1 again to enter add User card, and enter new User card, voice prompt: “Enrollment succeeded.”
• Press 1 to enter user Settings, press 1 to enter Add password, and enter the password again, and press # to confirm. Voice prompt: Enrollment succeeded.

Add a temporary User(OTP)

• In Master mode
• Press 1 to enter user Settings, press 2 to enter Add temporary password, enter temporary password again, and press # to confirm. Voice prompt: Enrollment succeeded.

Modify the Master PIN Code

• In master mode
• Press 1 to enter User Settings, then press 4 to enter modify Master Pin Code, enter the new Master Pin Code, press # to confirm, enter Master Pin Code, press # to confirm, Voice prompt: Set up succeeded.

Delete user

• In Master mode
• Press 1 to enter User Settings, then press 5 to enter delete user, then press 1 to delete single user password, user fingerprint (optional), user card, and enter user password \ User fingerprint (optional) \ user card, voice prompt: deletion succeeded.
• Press 1 to enter User Settings, then press 5 to delete a user, and then press 2 to delete all user passwords. The voice prompt: deletion succeeded, pin code database is empty。.
• Press 1 to enter User Settings, press 5 to delete users, and press 3 to delete all user fingerprints. The voice prompt: deletion succeeded, fingerprint database is empty.
• Press 1 to enter User Settings, then press 5 to enter user deletion, and then press 4 to delete all user cards. The voice prompt: Deletion succeeded and the card library is empty.

Opening mode settings

• In Master mode
• Press (1) for user setting, Then press(6) for opening mode.

1. Press (1) for normal mode(single verification) which opening by PIN code or fingerprint or card.
2. press (2) for security mode(double verification) which means opening by PIN code+fingerprint or PIN code+card or fingerprint +card.

Notice: In security mode, to delete all users is prohibited.

Enable/disable automatic mode

In Master mode

• Press 1 to enter user Settings, then press 7 to turn on/off automatic mode; voice Prompt: set up succeeded,auto-mode/manual mode.

Language Settings

• In Master mode
• Press 2 to enter the language Settings.
• Press 1 to select Chinese;
• Press 2 to select English;
• Press 3 to select Russian;
• Press 4 to select Spanish;
• Press 5 to select Portuguese.

Extended function

• In Master mode
• Press 4 to enter extended function Settings.
• Press 1 to join the network.
• Press 2 to log off the network.

Use your smart door lock

• Unlock from outdoor(Common mode)
• Touch the pad screen by palm to lighten keypad; then entering the enrolled PIN code with end of [#]. After voice prompt “verification succeeded”, push or pull handle to open the door.
• In common mode,Place the enrolled card properly on the card icon area. After voice prompt “verification succeeded”, push or pull the handle to open the door.
• In the common mode, directly put the finger that has been enrolled on the fingerprint sensor.
• Voice prompt: verification succeeded, please push or pull the handle to open the door.
• Under common mode, Enter incorrect Pin Code or card five times in a short period of time the lock will have a lockdown for 100S.
• Under security mode, Enter incorrect passwords card or Pin code five times in a short period of time the lock will have a lockdown for 100S.

Unlock by mechanical key

• You can unlock by mechanical key if you forget pin code , the battery run out or system error occurs.
• Insert the mechanical key and then rotate 180°to unlock. Push or pull to unlock.
• If your door is right opening direction, please turn the key clockwise.
• If your door is left opening direction, please turn the key counterclockwise.

Lock/unlock from in door

1. Locking button (close) press the close button to lock, long press the close button 3 seconds to enable privacy mode. In privacy mode , lock can be opened only by master pin code or unlock inside.
2. Unlocking button(open)double press the open button to unlock
3. Enable/ disable the sensor of inside handle, long press open and close button together 10s to enable/disable the sensor of inside handle.

Emergency Knob

• When system error occurs, you can rotate the knob to unlock Indoor
• Unlock by inside sensor handle
• Inside sensor handle enabled , holding the inside handel and cover the sensor to unlock.
• Inside sensor handle disabled, please press open button to unlock or enable sensor again.

Defense mode Enable/Disenable

1. Enable: After closing door, press the defense mode button to enable defense mode. voice prompt: defense mode enabled.
   • In defense mode, if someone unlocks from inside , the alarm will be triggered .
2. Disable: Defense mode will be disabled once it is unlock from outside.

Volume adjustment

• In the system setting, the volume is set to voice mode. When the door lock is wakened outdoors, long press the key to enter the mute mode.
• In the system setting, the volume is set to mute mode. When the door is wakened outdoor and no number is entered, press the key to temporarily switch to voice mode. If the screen is turned off and wakened again, the normal volume will be restored.

Other functions

Restore to factory settings

If you forgot the master pin code, you can take out the battery cover then double press the Reset button till Voice prompts restored to factory setting , please modify the master pin code immediatley. It means reset succeeded.

System reboot

• If you need to restart the system, you can use the charging bank as an emergency power supply and power on the door lock through the Micro USB interface to restart the system.

Emergency power supply

• When the battery voltage is low and cannot be turned on externally, you can use the 5V charger as an emergency power supply to power on the door lock through the Micro USB interface. After opening the door lock, replace the battery immediately.
• Note: When the battery power is too low,every time,after the lock is successfully unlocked,the system will give a voice prompt ：the power is low. please replace the battery; at this time, please replace the battery in time.

Replace battery

• When the system voice prompts: “The battery is low, please replace the battery”, the battery needs to be replaced in time.
• www.kaadasgroup.com
• Shenzhen Kaadas Intelligent Technology Co.,Ltd, reserve all rights for the final interpretation to this user manual

References

• Kaadas Official

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>