Kaadas S110-5W Smart Door Lock User Manual

Kaadas S110-5W Smart Door Lock

Product Information

• Key cylinder: The key cylinder is a component used for the manual unlocking and locking of the product.
• Outside positional component: This component is located on the exterior part of the product and can be removed by unscrewing it.
• Inside positional component: This component is located on the interior part of the product and can also be removed by unscrewing it.
• Master PIN code: The master PIN code is a default code used to access the product’s settings and modes. The default master PIN code is 12345678.
• User PIN code: The user PIN code is a code used by individual users to operate the product in normal mode or security mode.
• Security Mode: Security mode is one of the operating modes of the product. In this mode, additional security measures are activated.
• Normal Mode: Normal mode is the default operating mode of the product. It does not have additional security measures activated.
• Fingerprint capacity: The product has the capability to enroll and recognize fingerprints for access control.
• Card capacity: The product also supports card-based access control, allowing users to use cards for authentication.

Product Usage Instructions

1. To set up the product, ensure that all required components, such as the key cylinder, outside positional component, and inside positional component, are properly installed.
2. To switch between normal mode and security mode, follow these steps:
3. Access master mode by entering the master PIN code.
4. Once in master mode, select the desired mode (normal mode or security mode).
5. Setting the Master PIN code:
6. In normal mode, the default Master PIN code is 12345678.
7. In security mode, the default Master PIN code is also 12345678.
8. It is recommended to change the Master PIN code for enhanced security.
9. Setting User PIN codes:
10. In normal mode, you can set up to 20 groups of 6-12 digit User PIN codes.
11. In security mode, you can set up to 6 groups of 6-12 digit Normal PIN codes and 4 groups of 6-12 digit One-time PIN codes.
12. Accessing master mode:
13. To access master mode, enter the master PIN code.
14. Once in master mode, you can configure various settings and manage user access.
15. Enrolling fingerprints and cards:
16. Before setting to security mode, ensure that all required fingerprints and cards are enrolled.
17. In security mode, it is recommended to enroll at least two different opening ways, such as fingerprint, PIN code, and card.
18. User numbers:
19. In both normal mode and security mode, you can assign user numbers from 00 to 99 to individual users.

How to install

Package Content
This described package content is for reference only, the real products should be considered as final. If some components lost, please check with the sellers.

Explosive View

1. Back Cover
2. Connecting mounting screw (3pcs)
3. Inside escutcheon assembly
4. Pressure spring (2pcs)
5. Mounting plate
6. Mortise
7. Screw bolt (3pcs)
8. Outside escutcheon assembly
9. Square shaft (2pcs)
10. Fixed screw for key cylinder
11. Fixed screw (4pcs)
12. Key cylinder
13. Mechanical key cover

Caution: Please press the spring into the end of the square shaft before installing them.

Important Information

Safety instruction

• Read and understand all instructions before using this smart lock. Damages caused by failure to follow instructions is not covered by the warranty.
• It is recommended to use the enclosures/accessories specified by the company.
• Use only alkaline batteries configured with this product.
• Do not forcibly disassemble this product in order to avoid alarm sound or damage to the product.
• Do not scratch the fingerprint reader with sharp objects, otherwise, it may cause permanent damage.
• Do not expose the product to corrosive substances, so as not to damage the outer protective layer.
• Do not hand objects on the handle, so as not to affect the normal use of the door lock.
• When cleaning the product, please wipe it with a soft cloth.
• Do not disassemble the battery while the device is operating.
• Please choose a professional engineer to install the door lock follow the company’s standard installation instructions, and do not install it by yourself.
• After the door lock is installed, please modify the default master PIN code immediately and keep the mechanical key in a safe place. Don’t disclose the PIN code to an unknown person.
• When a low battery alarm is triggered, please replace all the batteries in time.

Warning

• Do not place the battery close to fire in case of explosion.
• Do not short-circuit the two poles of the battery lead with metal objects in case of explosion.
• Make sure replacement or maintenance is done by a professional person authorized by Kaadas.
• Your warranty may be invalidated if you use accessories produced by another manufacturer or not recommended by Kaadas.

Disposal of used battery and lock

• Please understand the local electronic product classification and collection system.
• Please follow the local regulations and do not discard used batteries into ordinary household garbage.
• Properly disposing of used products helps to avoid potential negative impacts on the environment and human health.

Before Installation

Check Door Open Direction

Change latch bolt direction

Change Handle Direction
Change Outside escutcheon Handle Direction

Change Inside escutcheon Handle Direction

Caution: The default screw pack is for door thickness 38-60mm, please contact our dealer if another screw pack is required.

Installation Steps

caution: Do not make the mortise deadbolt come out.

1. Mark and drill bores by using the installation template first, then fix the mortise into the doorframe and tighten the screws to fix the mortise on the door.
2. Put the key cylinder into the corresponding position of the mortise, then fasten it by tightening the screw.
   • caution: Spring: the big end is downward.
3. Fix 3 screw bolts on the front panel, place square shaft and pressure spring into the bore.
4. Pass the connection wire through the bottom bore. Then align and insert square into the mortise to make the front panel flat against the door closely.
5. Caution: According to the door thickness, cut the night latch key pick in proper length.
6. Place pressure spring and square shaft In the back panel in proper order. Insert the connecting cable of the front panel Into the related sockets of the back panel. Then align and insert the square shaft and mechanical key pick into mortise holes, make the back panel flat against the door closely. After that, tighten the 2 screws.
   • Caution:
   • After Installing the striker assembly, please check If the lock works smoothly by opening/closing the door.
   • Test If the mechanical key works smoothly after Installation.
7. Install the batteries and the battery cover. Then install the striker assembly to finish the installation. Please check the handle, safe handle switch, and mechanical key if they are working properly.

Product Overview

Outside escutcheon

Inside escutcheon

Caution: The pictures  above are just for reference, please refer to the real product as final.

How to set

Before set
There are normal modes and security modes in the product. The default mode is normal mode.

Caution: Before setting to security mode, -fingerprint, PIN code, and Card must be all enrolled or at least two different opening ways.

User Number

• When you in security mode, you shall edit the user number before enrolling the PIN code/fingerprint/card.
• When you need to delete one user, you can enter the user number to delete.
• You can fill your user information in the below sheet for convenience

Menu index

Caution:

1. There are voice prompts for the above operations, which can be operated according to the voice prompts
2. The user pin code and master pin code are 6-12 digits, and the default master pin code is 1 2345678.

Access Into master mode

The default master PIN code is 12345678.

1. Wake up touchscreen keypad with palm.
2. Press[*] twice, input master PIN code, and press[#] to confirm.
3. Voice guide: Enter the Master Mode.
   • Note: Change default master PIN code is required immediately for menu operation.

Change master PIN code

• In master mode
• Press 1 to user setting, then press 9 to change default master PIN code.
• Enter new master PIN code, press # to confirm. Reenter the master PIN code, then press # to confirm. Voice prompt of “Set up succeeded”

User Setting

Enroll user PIN code

• Access Into master mode
• Press [1) for user setting.Then press [1) to enroll user
• PIN code. Enter 2 digital user number (00-09), and confirm with [#) key
• Enter user PIN code (6-12 digits), and confirm with [#] key; Then repeat above operations . Voice prompt of “Enrollment succeed”

Enroll Fingerprint

• Access Into master mode
• Press [1 J for user setting.Then press [2) to enroll user fingerprint. Enter 2 digital user number (00-99), and confirm with [#) key..
• Place your finger on the fingerprint sensor, then take away your finger after voice prompt “Remove finger and scan again”. Repeat above steps multiple times until voice prompt “Enrollment succeed”.

Enroll Card

• Access into master mode
• Press [1] for user setting.Then press [3] to enroll user card. Enter 2 digital user number (00-99), and confirm with [#] key.
• Place card on the card icon area until beep sound and voice prompt “Enrollment succeed”.

Delete User PIN Code

• Access into master mode
• Press [1] for user setting.Then press [ 4] to delete user
• PIN code. Press [1] to delete single user. Enter 2 digital user number (00-09), and confirm with [#] key, Voice prompt of “Deletion succeeded”.
• Press [2] to delete all users.
• Voice prompt of “Deletion succeeded”

Delete User Fingerprint

• Access into master mode
• Press [1] for user setting.Then press [5] to delete user fingerprint. Press [1] to delete single user. Enter 2 digital user number (00-99), and confirm with [#] key.OR Place the related finger on the fingerprint sensor to delete until one beep sound. Voice prompt of “Deletion succeeded”
• Press [2] to delete a 11 users Voice prompt of “Deletion succeeded”

Delete User Card

• Access into master mode
• Press [1] for user setting.Then press [6] to delete user card.Enter 2 digital user number (00-99), and confirm with [#] key OR Place the related RF card on the card icon area to delete until one beep sound.
• Voice prompt of “Deletion succeeded”
• Press [2] to delete a 11 users
• Voice prompt of “Deletion succeeded”

Opening Mode Setting

• Access into master mode
• Press [1] for user setting.Then press [7] for opening mode setting.Press [1] for normal mode (single verification) ,which means opening by PIN code or fingerprint or card.
• Press [2] for security mode (double verification) ,which means opening by PIN code+flngerprint or PIN code +card or fingerprint +card.

System Setting Volume Setting

• Access into master mode
• Press [2) for system setting. Then press [ 1 ) for volume setting.
• Press [1) for voice mode.
• Press [2) for mute mode, excluding alarm and menu operation.

Language Setting

• Access into master mode
• Press [2) for system setting.Then press [2) for language setting.
• Press [1) for Chinese Voice.
• Press [2) for English Voice.
• Press [3) for Spanish Voice.
• Press [ 4 J for Portuguese Voice.
• Press [5) for Russian Voice.

System Query

• System Query
• Access into master mode
• Press [3) for system query.
• Press [ 1) to get a unique serial number.

Extension Function

• Access into master mode
• Press [ 4) for function extension.
• Press [ 1 ) to Join the network.
• Press [2) to log off-network.

How to use

Open from outside

1. PIN code opening
2. Fingerprint opening
3. Card opening
4. Touch the pad screen by palm to lighten the keypad; Enter the enrolled PIN code at the end of [#]. Voice prompt “door opened” . Press the handle to open the door.
5. Place the enrolled finger properly on the fingerprint sensor area until one beep sound and voice prompt “door opened” Press the handle to open the door.
6. Place the enrolled card properly on the card icon area until one beep sound and voice prompt “door opened”. Press the handle to open the door.

Caution:

In security mode, double verification is required for opening the door.

1. PIN Code + Fingerprint
2. PIN Code + Card
3. Fingerprint + Card

Open door by mechanical key override

• First. Lose the cover of the mechanical key from the position for pull, then rotate it 90 degrees.
• Next, insert the key into key hole and rotate it with proper angles.

Caution: In case of forgetting the PIN code, the battery runs out or system error, the mechanical key is used to open the door as backup mode.

Close door from outdoor/Close door from indoor/Double lock from indoor

Other Features

Restore to factory setting
Double click the [RES] button to make _ the lock restore to the factory – setting. Voice prompt “Restored to factory settings. Change master PIN code.” After that, all user information and settings will be cleared.

Reboot
If you need to restart the system, you can power on the door lock through the micro USB interface by using the 5V power bank as the emergency power supply.

Emergency power supply
When the battery voltage is too low to open the lock from outside, you can use 5V power bank to charge the door lock via Micro USB port. After the door is unlocked, please replace all batteries immediately. When tha lock system crash down, you can restart system by pressing the reboot button.

Caution: When the battery voltage is lower than 4. BV, voice prompts “Low battery, please replace all batteries” at each unlocking. Please replace all batteries immediately, and do not mix old batteries and new batteries together in replacement.

Safe Handle Feature

1. Enable: move the safe handle switch to display the ‘red’ mark. Once the safe handle feature is enabled, the indoor handle will be locked.
2. Disable: move the safe handle switch to display a ‘green’ mark. The indoor handle can be pressed and turned upward freely.

Battery Replacement

1. Battery life 1.5V AA Alkaline Battery is required. Total capacity is 8 pcs, divided into 2 groups. One group is ok for power supply, two groups can be used for a longer time.
2. Battery Replacement Reminder When the voice prompt “Low battery, please replace all batteries” ” Please replace the batteries in time.

Shenzhen Kaadas Intelligent Technology Co.; Ltd reserves all rights for the formal interpretation of this user manual. All designs and specifications are subject to change without notice. www.kaadasgroup.com.
Cautions: This section contains important information to ensure the user’s safety and prevent potential damage to property. Please, read this section carefully and use the product accordingly.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>