MUSIC STORE PURElight 3 Way Mini User Manual
- June 13, 2024
- MUSIC STORE
Table of Contents
PURE light 3 Way Mini
User Manual
Important safety instructions
Please read before connection!
DANGER! (Electrical shock due to high voltages in the device)
The housing must not be removed! There are no parts to be maintained in the
device.
Inside the unit there are components which are under high electrical voltage.
Before each use, check the device for damage or the absence of components,
protective devices or housing parts. If this is the case, the device must not
be used!
Leave maintenance and repair work to a qualified service workshop or contact
your dealer. In the case of a malfunction of the device, operation must also
be stopped immediately until the device has been repaired by a specialist!
DANGER! (Electric shock due to short circuit)
Modifications to the power cord or plug are prohibited. If the power cord is
damaged, it must be replaced immediately with an original spare part from the
manufacturer. Failure to do so may result in fire or death due to electric
shock!
DANGER! (For babies and children)
Dispose of or store any packaging material properly! Packaging material must
be kept out of the reach of babies and children due to the risk of
suffocation.
Ensure that children never use the appliance unattended! In addition, make
sure that children do not remove (small) parts from the device, as they could
suffocate by swallowing parts!
WARNING! (High light intensity – eye injuries)
A direct view into the light source is absolutely to be omitted!
WARNING! (Epilepsy)
Stroboscopic effects (flashes of light) can trigger seizures of epilepsy in
some people. Accordingly sensitive people should be warned and should not be
in the vicinity of such devices.
Hint! (Fire hazard due to overheating)
The maximum permissible ambient temperature of this device is 40°C.
Ensure that the unit is placed in a well-ventilated location away from direct
heat sources, naked flames, combustible materials, and liquids. A minimum
distance of 1 m is required.
Do not tape or cover the ventilation slots of the unit.
Hint! (Operating conditions)
Due to its structural characteristics, the device is designed for indoor
operation (IP20).
Never expose the device to rain, moisture or liquids as this may cause damage.
Vibrations, dust or sunlight can also cause damage, avoid them!
Hint! (Power supply)
It is essential that you check that the device voltage matches your local
mains voltage. It is highly recommended that you fuse your mains socket with a
residual current circuit breaker (FI).
If you do not use your device for a longer period of time or carry out
maintenance work, disconnect the device from the mains in order to minimize
danger. The same applies to storm conditions such as thunderstorms, floods,
etc.
Hint! (Error during data transmission)
Never connect the DMX input or output to audio devices such as power
amplifiers or mixing consoles!
DMX cables enable trouble-free operation and the highest possible transmission
reliability of signal data. Do not use microphone cables!
Hint! (Condensation)
To avoid condensation in the unit, the unit should adapt to the ambient
temperature before commissioning.
Hint! (Unwanted odours)
A new product can sometimes lead to unwanted odours. This reaction is normal
and disappears after a few minutes.
Symbols on device and packaging:
| The lightning flash symbol warns the user of uninsulated voltages and
the risk of electric shock.
---|---
| The exclamation mark symbol draws the user’s attention to important
maintains and operating instructions in the manual.
| Only suitable for indoor use.
| This symbol defines the minimum distance of the object to be illuminated.
****| Read the manual
Please read and follow the warnings and recommendations carefully to ensure safe and trouble-free use.
Installation
Be sure to check the unit for damage before use. Use the original packaging or
a suitable transport or storage packaging to protect the product from dust,
moisture, etc. when not in use.
The unit can be installed either upright or suspended. The device must always
be attached to a solid, approved carrier or a suitable surface. Note the load
limit of the selected installation position (e.g. for tripods).
The opening of the bracket must be used to fasten the device. Always provide a
second, independent safety backup for the device, e.g. with a safety cable.
Work on the device (e.g. assembly) should always be carried out from a stable
and permissible platform. Make sure that the area below you is closed off.
WARNING! (Risk of injury due to falling down)
Improper installation can cause considerable injury and damage!
The installation of the device should always be carried out by experienced
personnel and must be carried out in compliance with the mechanical and
electrical safety regulations in your country.
Please note that it is not possible to use this device with a dimmer!
Congratulations on your new PURElight 3-Way mini!
Thank you for choosing a PURE light product. Through efficient development
and economical production, PURE light enables high quality products at a
fantastic price.
Please read the instruction manual carefully to learn about all the features
of this product and keep it for future use.
Have fun with your new product!
Your PURE light Team
Guarantee
The current general terms and guarantee conditions of the Music Store
professional GmbH apply.
You can view it at: www.musicstore.de/
If you have any questions or suggestions, please contact us:
Music Store professional GmbH
Istanbulstr. 22-26
51103 Köln
Geschäftsführer: Michael Sauer
WEEE-Reg.-Nr. DE 41617453
Tel: +49 221 8884-0
Fax: +49 221 8884-2500
[email protected]
Scope of delivery
| Content | Quantity |
|---|---|
| 3-Way mini Moving Head | 1 |
| Power Cord | 1 |
| Manual | 1 |
Intended use
The PURE light 3-Way Mini was designed for use as an electronic LED lighting
effect. The device may only be used for this purpose and in accordance with
the operating instructions. Other purposes as well as operation under other
operating conditions are expressly not intended and can lead to damage to
property or personal injury! No liability is assumed for damage resulting from
improper use.
It must be ensured that the device is operated exclusively by trained and
competent users who are in full possession of their mental, physical and
sensory abilities. The use of other persons is expressly only permitted at the
request of a person responsible for their safety, who instructs or supervises
the use.
Setup
All connections of the device should be made before switching on. Only use
high-quality cables that are as short as possible for the connections.
Configuration oft he DMX connector
Resistance 120 ohm // ¼ w between pin 2 (DMX-) and pin 3 (DMX+) oft he last
fixture.
Operating mode DMX:
Connect the DMX input of your device to the DMX output of your DMX controller,
your DMX software or the DMX output of a device already in your DMX line.
Always use a DMX cable with a 110 Ohm resistor for this connection. Address
the device according to your DMX configuration.
The following table shows the respective DMX modes of the individual devices
with the corresponding values and functions:
Channel Mode
| Channel | Value | Function |
|---|---|---|
| 1 | 000-255 | PAN 0° to infinite |
| 2 | 000-255 | TILT 0 to 270° |
| 3 | 000-127 |
128-191
192-255| Offset Position Positive Rotation
Reverse Rotation
4| 000-255| Master Dimmer (0 % to 100 %)
5| 000-255| Red Dimmer (0 % to 100 %)
6| 000-255| Green Dimmer (0 % to 100 %)
7| 000-255| Blue Dimmer (0 % to 100 %)
8| 000-255| White Dimmer (0 % to 100 %)
9| 000-255| Stroboscope (Speed: slow to fast)
10| 000-255| Auto Show
11| 250-255| Reset
Channel Mode
| Channel | Value | Function |
|---|---|---|
| 1 | 000-255 | PAN 0° to infinite |
| 2 | 000-255 | PAN fine adjustment |
| 3 | 000-255 | TILT 0 to 270° |
| 4 | 000-255 | TILT fine adjustment |
| 5 | 000-255 | PAN/TILT Speed (slow to fast) |
| 6 | 000-127 |
128-191
192-255| Offset Position
Positive Rotation Reverse Rotation
7| 000-255| Master Dimmer (0 % to 100 %)
8| 000-255| Red Dimmer (0 % to 100 %)
9| 000-255| Green Dimmer (0 % to 100 %)
10| 000-255| Blue Dimmer (0 % to 100 %)
11| 000-255| White Dimmer (0 % to 100 %)
12| 000-255| Stroboscope (Speed: slow to fast)
13| 007-255| Macros
14| 250-255| Reset
Static, Auto or Sound mode:
The device contains automatic programs that run according to fixed schemes
(Auto) or are recalled via the built-in microphone to match the music (Sound).
The selection of the respective mode takes place via the menu directly on the
device.
If you connect several devices of the same type via DMX, they can be
controlled simultaneously via the master device. To do this, set the desired
function “Master” on the first device of the line, the other devices of the
series must now be set as “Slave”. Now the first device of the line gives the
function to all other devices and all devices run simultaneously.
Operation:
Start:
Connect the device to the mains and wait a few seconds until it is ready
for operation.
Connections and controls:
| No. | Designation | No. | Designation |
|---|---|---|---|
| 1 | Projector Head | 6 | DMX In (3-pole) |
| 2 | LED Lenses | 7 | DMX Out (3-pole) |
| 3 | Projector Arm | 8 | Power Twist Input |
| 4 | Menu Display | 9 | Power Twist Output |
| 5 | Menu Buttons |
Menu:
Navigation in the menu is via the four menu buttons below the display. Use
the “Mode” button to activate the menu, navigate via the “Up” and “Down”
buttons. A corresponding selection is confirmed with the “Enter” key.
The menu structure in detail:
| Menü | Wert | Function |
|---|---|---|
| Doxes **Address** | A001-A512 | Setting DMX address |
| Channel Set | 11CH/14CH | DMX channel selection (11 or 14 channels) |
| Show Mode | DMX Mode Fast Mode Slow Mode | |
| Soud Mode | DMX-Mode Show-Mode, fast Show-Mode, slow Sound control | |
| Sound Sense | 0-99 | Setting the microphone sensitivity for music control |
| Pan Inverse | OFF | |
| On | PAN |
PAN-Inverse
Tilt Inverse| OFF
On| TILT
TILT-Inverse
Default confirm| Yes| System reset
Fixture Reset| Yes| System reset
Specifications
| Model | 3-Way mini |
|---|---|
| Power Supply | AC110-240V, 50/60Hz |
| Power Input | 100 W |
| LEDs | 6 x 15W (4in1) |
| Colour Mixing | RGBW |
Red – Green – Blue – White
Beam Angle| 6°
Max. PAN Movement| 0° to infinite
Max. TILT Movement| 0° to 270°
Dimmer| 0 – 100%, Linear Dimmer
Stroboscope| 0 – 25 Flash/Second
Operating Modes| DMX, Automatic Mode, Sound Control Mode, Master/Slave
DMX Channels| 11 or 14
Connections| DMX-In/-Out (3-pole) Power Twist (In/-Out)
Dimensions (L x W x H)| 330 x 280 x 260 mm
Weight| 3,5 kg
Troubleshooting
The following overview serves as an aid for quick troubleshooting. If you are unsure, contact the manufacturer, the dealer or the corresponding specialist personnel. Never open the device on your own!
| Symptom | Troubleshooting |
|---|---|
| No function | Check the mains connection and the fuse |
| No reaction in DMX mode | Check the cable connections |
Check your DMX address setting
If available, try an alternative DMX controller
No reaction in remote mode| Change the battery in your remote control
Ensure that the IR transmitter and receiver are at close and clear distances
from each other
If the specified corrections have not led to success, please contact our service staff. The contact details can be found at www.musicstore.de
Cleaning
Regular cleaning of the device from dirt and dust increases the shelf life of
the product. Always disconnect the device from the power supply before
cleaning it! Never clean the appliance wet!
Optical lenses should be cleaned with a dry microfiber cloth to optimize light
output. Ventilation grilles and openings should always be cleaned of dust and
dirt. Suitable compressed air sprays are recommended for this application.
Environmental protection
The company MUSIC STORE professional GmbH always strives to reduce the burden
of packaging to a minimum. The use of environmentally friendly and recyclable
materials is of fundamental importance to us. Please dispose of and recycle
the packaging components after use properly.
Disposal of packaging:
Ensure that paper packaging, plastic materials, etc. are separately recycled.
Observe the corresponding disposal instructions on the packaging.
Disposal of batteries:
Batteries do not belong in the garbage! Please keep batteries in accordance
with the official collection points or disposal stations in accordance with
the specifications.
Disposal of your old device:
Do not dispose of the device with household waste! This device is subject to
the WEEE Directive (Waste Electrical and Electronic Equipment) in its
currently valid version.
The device will be disposed of by an approved waste disposal company or your
local waste disposal office. The regulations valid in your country must be
observed
Hersteller: MUSIC STORE professional GmbH,
Istanbulstraße 22-26,
51103 Köln, Deutschland MS ID: LIG0016868-000
07/2020
References
- MUSIC STORE - Online Shop für Musikinstrumente - Deutschland | MUSIC STORE professional
- Music Store Online-Shop für Musikinstrumente | MUSIC STORE professional