belisaire HH-6611Y Childrens Car Remote Control Instructions
- June 13, 2024
- belisaire
Table of Contents
belisaire HH-6611Y Children’s Car Remote Control
Product Information
| Product Type | HH-6611Y |
|---|---|
| Battery Specification | 1.5V (AAA) * 2 Section |
| Operating Voltage | DC2.0-3.6V |
| Quiescent DC | 0.5uA |
| Modulation Mode | GFSK |
| Transmission Frequency | 2.400-2.483GHz |
Product Usage Instructions
- To use the Baby Carriage Remote Control, make sure it is powered by two AAA batteries with a voltage range of 1.5V to 3.6V.
- Ensure that the device is in the operating voltage range mentioned above to avoid any malfunction.
- The remote control utilizes a GFSK modulation mode for transmission.
- The transmission frequency of the remote control is between 2.400GHz and 2.483GHz.
- Observe FCC regulations and guidelines for operation to prevent harmful interference.
- If the device causes undesired operation, reorient or relocate the receiving antenna, and increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected to minimize interference.
- If you require assistance or have any questions, consult the dealer or an experienced radio/TV technician.
OVERVIEW
- Baby carriage remote control product manual
- 2.4G wireless transmitter remote control
- Product Type : HH-6611Y
Product Configuration
- Battery Specification: 1.5V(AAA)*2
- Section Operating Voltage: DC2.0-3.6V Quiescent DC:0.5uA
- Modulation Mode: GFSK
- Transmission frequency: 2.400-2.483GHz
- This remote control shares 6 units at 2.419GHz, 2.425GHz, 2.445GHz, 2.450GHz, 2.470GHz, and 2.474GHz
- Frequency point. When conducting fixed-frequency testing, select high-, medium-, and low-frequency points for testing.
- Simultaneously press the three buttons “front+left+brake”, load the battery, and power it on to enter the fixed frequency test mode. By default, enter mode 1
- Frequency transmission mode, with a frequency point of 2.474GHz, and LED1 constantly on for prompt.
- Afterward, release all buttons and press the “swing” button to switch modes.
- Press the “swing” button for the first time to switch to mode 2: fixed frequency transmission mode, with a frequency point of 2.445GHz and LED2 constantly on.
- Press the “swing” button for the second time to switch to mode 3: fixed frequency transmission mode, frequency point 2.419GHz, LED1, LED2 Highlight the prompt.
- Press the “swing” button for the third time to switch to mode 4: fixed frequency reception mode, with a frequency point of 2.474GHz and LED 3 constantly on.
- Press the “swing” button for the fourth time to switch to mode 5: fixed frequency reception mode, frequency point 2.445GHz, LED1, LED3 Highlight the prompt.
- Press the “swing” button for the fifth time to switch to mode 6: fixed frequency reception mode, frequency point 2.419GHz, LED2, LED3 Highlight the prompt.
- Press the “swing” button for the 6th time to switch to mode 7: single carrier mode, frequency 2.474GHz, LED1, LED2, LED3 Always on the prompt.
- Press the “swing” button for the 7th time to switch to mode 8: single carrier mode, frequency 2.445GHz, LED1, LED2, LED3 All off prompt.
- Press the “swing” button for the 8th time to switch to mode 9: single carrier mode, frequency 2.419GHz, LED1, LED2, LED3 Always on the prompt.
- Press the “swing” button for the 9th time to return to mode 1: fixed frequency transmission mode, with a frequency point of 2.474GHz and LED1 constantly on.
- Press for the 10th time and return to mode 2, repeating the cycle.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that
may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
NO.20,4/F,Building 1,NO36,Hong song road,High-techzone zhengzhou
Documents / Resources
|
belisaire HH-6611Y Childrens Car Remote
Control
[pdf] Instructions
HH-6611Y, HH-6611Y Childrens Car Remote Control, Childrens Car Remote Control,
Car Remote Control, Remote Control, Control
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>