LIVALL C1ScQ85ti8L Smart Bike Helmet User Manual

LIVALL C1ScQ85ti8L Smart Bike Helmet

Product Information

The BH6X&MT and BH6X&MT Neo are smart cycling helmets manufactured by LIVALL. These helmets are equipped with various features to enhance the cycling experience. The helmets come with a speaker, microphone, indicator light, charging port, tail light, main control, buckle, adjustment knob, front chinstrap, and rear chinstrap. The control unit on the helmet may have either buttons or + and – buttons, depending on the version.
Please note that the actual product may differ slightly from the picture shown in the manual. For the latest information and updates, you can visit the official website of LIVALL at www.livall.com.

Packing List

(A few models are not equipped with remote controller due to different configurations of the products.)

• Helmet x 1
• Quick Start Guide x 1
• Bling remote controller x 1
• Magnet USB charging cable x 1
• Important Information and Warranty Card x 1

Wearing Instructions

To ensure proper usage and safety, follow these instructions:

• Adjust the length of the chinstrap to fit comfortably under your chin.
• Leave a gap as thick as one finger between your chin and the chinstrap.
• Check whether the buckle is properly fastened.
• Position the helmet correctly on your head.

Operating Instructions

Before using the helmet, make sure to charge the battery. Note that some models may not have Bluetooth speakers, which means they cannot be used for calls, music, or voice prompts.

Start-Up

To power on the helmet:

1. Press and hold the function button for 3 to 5 seconds.
2. You will hear a voice saying “POWER ON”.
3. The rear lights will come on, indicating successful power-up.

Connecting for the First Time or Switching Devices
Connecting for the first time or switching devices(Please refer to specific functions of the helmet when using the remote controller keys.)
One helmet can be connected to up to two LIVALL-authorized devices at the same time. After the handlebar remote control is connected, press the “left” or “right” button to control the helmet’s corresponding indicator light.

Connecting for the first time

• Turn on the device, which should be within 5 meters of the helmet. It will automatically connect the helmet.
• After the connection is established, it will be confirmed with two “beeps”.(The helmets without Bluetooth speakers could not hear such voice prompts. Please check the taillight to see if the helmet is connected successfully.)

Replacing device

To connect the helmet to a mobile phone:
(Tip: Once connected, the helmet can control the music player and make/receive calls. For stable connection, position your mobile phone in front of you.)

• Place a device that is already ON near the helmet’s main control.
• When the warming light flashes and the helmet speakers emit two “beeps”, it indicates that there is a device nearby requiring connection to the helmet.(The helmets without Bluetooth speakers could not hear such voice prompts.)
• Press the ” □” button on the helmet within 10 seconds after you hear the beeps and confirm connection to the device.When pressing the arrow left or right key on the bling jet remote, the right or left turning signal appears.

Connect to the phone

(Tip: Once connected, it can control the music player as well as make and receive calls. To ensure the stability of the connection, please try to position your mobile phone in front of you.)

• When the device is off, press and hold the ” □ ” button until you hear the “Pairing…” sound.
• Swith on the Bluetooth on your phone and scan for the “Helmet Phone” device.
• Click to connect. The speakers on both sides will make the “Connected” sound when the connection is completed.

After the connection is completed, you can play music as well as make and answer calls as follows

• To Play/Pause Music :  Press the ” □ ” button on the helmet or the handlebar remote control to play/pause music.
• Adjust Volume: When calls are made or music is played, press the “up/down” buttons on the handlebar remote control or press the “</>” buttons on the helmet to adjust the speaker volume .
• Previous Song/Next Song: Press the “up/down” buttons on the handlebar remote control or press and hold “</>” buttons on the helmet to cycle through the music.
• Answer/Reject Calls:   When there’s an incoming call, press the ” □ ” button to answer the call or press and hold to hang up.
• Dial Back : Two quick presses of the ” □ ” button on the handlebar remote control or helmet to redial the last outgoing call.

Power Off

• Press and hold the ” □ ” function button for 3 seconds.
• You will hear “POWER OFF”.(The helmets without Bluetooth speakers could not hear such voice prompts.)
• This device is successfully powered down when the rear lights go off.

Charging

• To charge
  Plug the USB charging cable into the USB port on the helmet. The tail charging light is illuminated in red, indicating that the helmet is being charged.

• Charging time
  It is recommended that the power of the charger is no less than 0.5A. Charging time takes about 3hours.

• Charging complete
  When the charging indicator light turns off, it indicates that charging is complete.

Note: When the front indicator light of the helmet lights up to show the charging status. When the front indicator goes off to indicate the full charge status.
Connect LIVALL Riding phone App
(for use the Walkie-Talkie function and take photos)
Only if the helmet is successfully connected to LIVALL App, SOS alert feature and LED light indicators can work.
For Android: Start LIVALL Riding. The App will automatically connect to the helmet;
For IOS: Follow LIVALL Riding guide to connect to the helmet.

Introduction

Welcome to the User Guide for LIVALL smart cycling helmets. This Guide will help you better use this product. With continuous improvements of our products, this Guide will be updated from time to time. You can access the latest version and learn more about the helmet on www.livall.com. Note:

1. The picture is for reference only. If the actual product appears different from the picture, the real product shall prevail.
2. Due to different version, some control unit use “<“and “>” buttons, some may use “+” and “-” buttons, both represent the same function.

Instructions for Bling remote controller

Tip:
To ensure signal stability for connection, please try not to place your mobile phone right against your body.

Features

New Features (only available for BH60SE Neo, MT1 Neo, BH62 Neo, BH61S Neo)

1. Battery Status
   Remaining battery level is shown by the number of the first row of LEDs (BH60SE Neo,MT1 Neo,BH61S Neo), or
   the number of “V-shaped” LEDs (BH62 Neo), that are displayed when a helmet is initially turned on. Full battery is indicated when all of the LEDs are on.

2. Brake Warning Light
   Activated when the built-in-accelerometer sensor detects a significant deceleration, the rear lights will be enhanced for a few seconds to draw attention from surrounding traffic.
   Please note: if the helmet repeatedly shakes, the built-in sensor will detect significant deceleration, which may trigger the brake warning lights.

3. Auto On/Off
   After the helmet powers on and stays stationary for a while, it will automatically begin saving power by going into sleep mode. When the tail light is off, without user interaction, the helmet is in sleep mode.To wake up the helmet, shake it several times until the tail lights illuminate.
   Note: If the helmet does not wake up, make sure the battery levels are adequate.

4. Anti-Loss Alarm
   Prompted when a user’s helmet is connected to the LIVALL riding app and the distance between the helmet and smartphone exceeds 15m, both the helmet and smartphone will trigger an alarm to alert the user.

5. One-Click Voice Command
   After both connections are successful (the remote control is connected to the smart helmet and the helmet is connected to a smartphone via Bluetooth), click the intercom button on the remote control to activate the smartphone’s voice assistant service.

Kind Reminder: Please refer to the Quick Start Guide for more details about the functions.

Considerations

1. The helmet contains electronic parts inside. Please do not take a long ride in the rain although the helmet can prevent the rain from splashing.
2. After the helmet gets wet in the rain, the water droplets might occur in the chimney of tail LED lights. The water droplets will disappear when you put the helmet under the ventilation environment for 1-2 days.
3. The helmet contains the battery. The battery capacity varies with temperature change. The battery life can decay when the helmet is used at low temperatures or below Zero degrees Celsius.
4. Trying to clean the golden colour contacts of the charging plug sheet with metal or hard tools such as blades or tweezers is strictly forbidden. Please use cotton swabs with clean water or alcohol in case of cleaning. Please make sure the charging plug is clean and try while charging the helmet.
5. If the electronic functions do not work, please charge the helmet for 3 hours and then check if it works normally.
6. The helmet contains impact detection devices. Only if you connect your helmet with LIVALL App, start ride mode on the App and your helmet suffers from the heavy impact, SOS alert feature can be triggered. Your emergency contacts set on LIVALL App can accordingly receive your SOS messages.

Note:

1. Problems such as network anomalies, may result in the failure to successfully send or receive SOS messages.
2. To maintain efficient battery life, it is recommended that the helmet be fully charged before any long-term storage (six months to one year).

Technical Specifications

Charging port : Magnet USB Charging cable Electricity parameter : DC 5V/0.5A
Charging time : 3-4 hours Waterproof class: IPX4
Battery life : The max. battery life of the light is 10 hours. Listening time for music is 3-to-6 hours.
Temperature: Storage Temperature: -20°C ~45°C. Temperature for use: 0°C~40°C. Temperature while charging: 0°C~40°C.
Notes: The above data is measured by LIVALL in a controlled environment, with room temperature at 25°C, specific light patterns and smartphone volume at 60%. The data may vary according to the environment.
Performance standards:

• USA:                    16 CFR 1203
• Europe:                EN 1078:2012+A1:2012
• Australia:              AS/NZS 2063:2008

Australian agent: LIVALL (NZ) SPORTS TECH LIMITED Add:62 Jeffs Road, Dairy Flat Highway, Auckland 0794, New Zealand

• That the helmet can only protect if it fits well and that the buyer should try different sizes and choose the size which feels secure and comfortable on the head.
• That the helmet should be adjusted to fit the user e.g. the straps positioned so that they do not cover the ears, the buckle positioned away from the jawbone and the straps and buckle adjusted to be both comfortable and firm.
• How the helmet should be position on the head to ensure the intended protection is provided (e.g. that it should be placed so as to protect the forehead and not be pushed too far over the back of the head.
• That a helmet cannot always protect against injury.
• That a helmet subjected to a severe impact should be discarded and destroyed.
• A statement of the danger of modifying or removing any of the original component parts of the helmet other than as recommended by the manufacturer, and that helmets should not be adapted for the purpose of
  fitting accessories in a way not recommended by the manufacturer

Electronic functions troubleshooting

During the usage, if the following troubles occur, please charge the product according to quick guide of the model(the helmet can be reset during the charging). If the problems still can not be solved, please contact the after- sales service center. (After-sales email: riding@livall.com)
Faults:

• Can not be charged or turn-off normally;
• The helmet is turn on, but the lights, micphone, speakers etc can not work normally;
• After power on, it turns off automatically in a short time.
  Note: Please refer to the quick guide of the specific model for function details.

References

• LIVALL Smart Wearables & Accessories – LIVALL RIDING
• LIVALL Smart Helmets with Fall Detection | Innovative Cycling Gear – LIVALL RIDING

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>