LIVALL L3101 Smart Helmet User Guide

LIVALL L3101 Smart Helmet

Product Information

LIVALL smart helmets are equipped with various smart features to enhance your cycling experience. These features include:

• Built-in SOS fall detection
• LED lighting
• Sleek and waterproof design

The helmet is continuously improved, and the user guide is periodically updated. For the latest version of the guide and more information about the helmet, please visit the official website: www.livall.com.

Packing List

• Helmet x 1
• Quick Start Guide & Warranty Information x 1
• Magnetic USB charging cable x 1
• Visor x 1
• Visor Screw x 1

Wearing Instructions
To ensure proper usage and safety, follow these instructions:

1. Adjust the length of the chinstrap correctly.
2. Leave a gap as thick as one finger between your chin and the chinstrap.
3. Position the helmet correctly on your head.
4. Check if the buckle is properly fastened.

Power On/Off
To power on the helmet, hold the button at the back of the helmet for 2 seconds. The LED taillight will blink for 10 seconds, indicating that the helmet is powered on and in adaptive warning light mode.

To power off the helmet, hold the button at the back of the helmet for 2 seconds until all the LED taillights turn off.

Lighting Modes
After powering on the helmet, you can switch between three lighting modes:

• Tap the button once: Adaptive Warning Lighting – In daylight or bright environments, only the central LED will flash. In dark environments, the whole taillight will flash.
• Tap the button twice: Brake Warning Light – The whole taillight will light up for 3 seconds to warn vehicles behind when a clear deceleration is detected.
• Tap the button three times: Auto Power-off – The helmet will automatically power off after being stationary for 3 minutes.

Auto Power-on
When the battery of the helmet is charged, shaking the helmet a few times will automatically power it on. This function can be activated in the settings of the LIVALL Riding App.

Charging
To charge the helmet, open the soft rubber lid with the image of a charging port. Connect the magnetic charging port to a USB cable and insert it into the USB charging port interface of the helmet. Charging starts when the central LED blinks. When the central LED stops blinking and turns off, charging is completed.

Connecting to Phone
To connect the helmet to your phone:

1. Turn on the helmet.
2. Switch on the Bluetooth on your phone.
3. Click to connect the Bling Helmet device in the LIVALL Riding App.

Introduction

Welcome to the User Guide for LIVALL smart helmets. Smart features include built-in SOS fall detection, LED lighting, and sleek, waterproof design.This Guide will help you better use this product. With continuous improvements of our products, this Guide will be updated from time to time. You can access the latest version and learn more about the helmet on www.livall.com.

Note:
The picture is for reference only. If the actual product appears different from the picture, the real product shall prevail.

Packing List

• Helmet x 1
• Quick Start Guide & Warranty Information x 1
• Magnetic USB charging cable x 1
• Visor x 1
• Visor Screw x1

Wearing Instructions

Power on
Hold the button at the back of the helmet for 2 seconds, then the LED taillight will blink for 10 seconds after the helmet is powered on, which means the helmet automatically enters adaptive warning light mode.

Remark:
When powering on, you could check the remaining battery level of the helmet by the number of tail lights, all the lights on indicates full power.

Power off
Hold the button at the back of the helmet for 2 seconds until all the LED taillight turns off.

Lighting Mode

lighting mode:
After the helmet is power on, tap the button for a second to switch the three lighting modes in order.

Adaptive Warning Lighting
This function is enabled by default.When it is active, In daytime or in a bright environment, only the central LED will keep flashing, other LED will turn off automatically. While at night or in a dark environment, the whole taillight will keep flashing automatically.

Brake warning light
When the helmet detects a clear deceleration, the whole taillight will light up for 3 seconds to warn the vehicles behind.

Comment:
When the helmet shakes too heavy, the built-in sensor detects obvious deceleration to trigger the warning light always on, which is normal.

Auto Power-off
When the helmet keeps stationary for 3 minutes, it will automatically power off.

Auto Power-on
When the battery of the helmet is charged, shake the helmet a few times. It will power on automatically. (This function is off in the factory default setting, you can activate the function in the settings of LIVALL Riding App)

Charging
When the soft rubber lid with “ ” image is opened, the Magnetic charging port will be seen. Insert a USB cable into the USB Charging cable interface of the helmet. Charging starts when the central LED blinks. During charging, when the central LED stops blinking and turns off, charging is completed.

Connect to the phone (Tip: Once connected, to ensure the stability of the connection, please try to position your mobile phone in front of you.)

LIVALL Riding App

Only if the helmet is successfully connected to LIVALL Riding App, SOS alert feature can work.

NO| Function|
---|---|---
1| Quick Flashing Light, Tidal Light|
2| Adaptering light|
3| Brake warning light|
4| Auto-power off|
5| Auto-power on|
6| SOS Alert|

Technical Specifications

• Model: L3101
• Charging port: Magnetic USB
• Battery: 3.7V/455mAh
• Waterproof class: IPX5
• Electricity parameter: DC 5V/1A
• Charging time: 2-3 hours
• Battery life: About 15-20 hours in default flashing mode
• Temperature: Storage
• Temperature: -20°C ~45°C.
• Temperature for use: 0°C~40°C.
• Temperature while charging: 0°C~40°C.

Notes:
The above data is measured by LIVALL in a controlled environment, with room temperature at 25°C and specific light patterns. The actual data might be different according to the environment.

Performance standards:

• NTA 8776:2016-12
• EN 1078: 2012+A1:2012

Considerations

1. The helmet contains electronic parts inside. Please do not take a long ride in the rain although the helmet can prevent the rain from splashing.
2. After the helmet gets wet in the rain, the water droplets might occur in the chimney of tail LED lights. The water droplets will disappear when you put the helmet under the ventilation environment for 1-2 days.
3. The helmet contains the battery of 3.7V/455mAh. The battery capacity varies with temperature change. The battery life can decay when the helmet is used at low temperatures or below Zero degrees Celsius.
4. Trying to clean the golden colour contacts of the charging plug sheet with metal or hard tools such as blades or tweezers is strictly forbidden. Please use cotton swabs with clean water or alcohol in case of cleaning. Please make sure the charging plug is clean and try while charging the helmet.
5. If the electronic functions do not work, please charge the helmet for 3 hours and then check if it works normally.
6. The built-in battery is forbidden to be disassembled, squeezed, heated or burned. It is also forbidden to use screwdrivers and other sharp devices breaking down or prying apart the battery. The above operations may make the battery caught fire.
7. Please do not place the helmet with sharp objects, avoiding to damage the helmet.
8. The helmet contains impact detection devices. Only if you connect your helmet with LIVALL Riding App, start ride mode on the App and your helmet suffers from the heavy impact, SOS alert feature can be triggered. Your emergency contacts set on LIVALL Riding App can accordingly receive your SOS messages.

Note:

1. Problems such as network anomalies, may result in the failure to successfully send or receive SOS messages.
2. To maintain efficient battery life, it is recommended that the helmet be fully charged before any long-term storage (six months to one year).

Instructions for Use and Care

1. That the helmet can only protect if it fits well and that the buyer should try different sizes and choose the size which feels secure and comfortable on the head.
2. That the helmet should be adjusted to fit the user e.g. the straps positioned so that they do not cover the ears, the buckle positioned away from the jawbone and the straps and buckle adjusted to be both comfortable and firm.
3. How the helmet should be position on the head to ensure the intended protection is provided (e.g. that it should be placed so as to protect the forehead and not be pushed too far over the back of the head.
4. That a helmet cannot always protect against injury.
5. That a helmet subjected to a severe impact should be discarded and destroyed.
6. A statement of the danger of modifying or removing any of the original component parts of the helmet other than as recommended by the manufacturer, and that helmets should not be adapted for the purpose of fitting accessories in a way not recommended by the manufacturer.
7. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
8. Take good care of the product, do not wash the surface of the helmet with corrosive solvent, do not strike the helmet;
9. Validity: Valid for 3 years without impact and under normal use.

Electronic functions troubleshooting

During the usage, if the following troubles occur, please charge the product according to quick guide of the model(the helmet can be reset during the charging). If the problems still can not be solved, please contact the after- sales service center. (After-sales email: user@livall.com)

Faults:

1. Can not be charged or turn-off normally;
2. The helmet is turn on, but the lights, micphone, speakers etc can not work normally;
3. After power on, it turns off automatically in a short time.

Note: Please refer to the quick guide of the specific model for function details.

This helmet is in conformity with the regulation (EU) 2016/425 and Regulation 2016/425 on personal protective equipment, as amended to apply in GB. Hereby, LIVALL Tech Co., Ltd. declare that the radio equipment type Smart Helmet is compliance with Directive 2014/53/EU.

Fcc Statement

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

LIVALL Tech Co., Ltd. declare that the full EU Declaration of conformity and UK Declaration of conformity are available on the Internet at http://www.livall.com/tech/product.html.

Approved body:

• For helmet only: ITS Testing Services(UK) Ltd., Centre Court, Meridian Business Park, Leicester LE19 1WD. UKCA AB0362 Notified Body:
• For helmet only: Nederland B.V. with its office located at Wilmersdorf,50,7327 AC Apeldoorn, The Netherlands. Notified Body No. 0063

The EU declaration of conformity can be found at the following link: www.livall.com/english/tech/product.html NTA8776:2016-12

• Original Design Manufacturer: LIVALL Tech Co., Ltd.
• Address: 4th Floor, Building 8, No.919, Huawei Road, Xiangzhou District, Zhuhai, China.
• Postal Code: 519000
• Website: www.livall.com.
• Support & Service E-mail: user@livall.com.

References

• LIVALL Smart Helmets with Fall Detection | Innovative Cycling Gear – LIVALL RIDING
• FAQs – LIVALL RIDING
• Accessories – LIVALL RIDING

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>