Infinix X6832 Smartphone User Manual
- June 13, 2024
- Infinix
Table of Contents
Infinix X6832 Smartphone
Product Information
Infinix X6832
The Infinix X6832 is a mobile phone with various features and components. It has a front camera, volume keys, a power key, a side fingerprint sensor, and NFC capability. The device operates on the Android operating system.
Explosion Diagram Specification
The explosion diagram specification provides a detailed list of the components and parts of the Infinix X6832. It includes items such as CTP+LCM, PCBA MB, fingerprint sensor, camera modules, waterproof frame, card holder, screws, and more.
SIM/SD Card Installation
To install the SIM card or SD card, follow these steps:
- Power off the mobile phone.
- Refer to the provided picture for SIM/SD card installation instructions.
Charging the Phone:
To charge the Infinix X6832, you have two options:
- Use a charger compatible with the device.
- Connect the phone to a computer using the USB cable provided with the phone.
Note : It is important to use only INFINIX chargers and cables. Using other chargers or cables may damage the device and void your phone warranty.
FCC Caution
The Infinix X6832 complies with Part 15 of the FCC Rules. It must not cause harmful interference and must accept any interference received. Any changes or modifications not approved by the responsible party may void the user’s authority to operate the equipment.
Specific Absorption Rate (SAR) Information
The mobile phone meets government requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations.
Operating System
The Infinix X6832 runs on the Android operating system, which is a trademark of Google LLC.
Explosion diagram specification
1 | CTP+LCM | 2 | FRONT COVER FRAME |
---|---|---|---|
3 | PCBA MB | 4 | REC |
5 | FINGERPRINT | 6 | CAM AF 50M |
7 | CAM FF | 8 | CAM FF 8M |
9 | REC DECO PART | 10 | F CAM FRAME |
11 | RAD FILM MB SHIELD | 12 | LT SENSOR RUBBER |
13 | BTB RUBBER 1 | 14 | R CAM CON FOAMS 50M |
15 | MAIN WATERPROOF FRAME | 16 | MAIN WATERPROOF MYLAR |
17 | CARD HOLDER | 18 | MI HOUSING |
19 | ANT MYLAR 1 | 20 | RAD FILM MI HOUSING |
21 | CAM LENS 1 | 22 | CAM LENS 2 |
23 | ANT MYLAR 2 | 24 | ANT MYLAR 3 |
25 | SCREW L2.5 | 26 | SCREW L3.5 |
27 | BAT COVER ASM | 28 | NFC |
29 | SPK FRAME ASM | 30 | RCAM LOCATION FRAME ASM |
31 | BTB RUBBER 2 | 32 | RUBBER USB |
33 | BTB RUBBER 3 | 34 | RUBBER EARPHONE |
35 | LCD FPC MYLAR | 36 | FPCA SIDEKEY |
37 | CAM FF RUBBER | 38 | BTB RUBBER 4 |
39 | BTB RUBBER 5 | 40 | BTB RUBBER 6 |
41 | SPK | 42 | MOTOR LINEA |
43 | BAT | 44 | FPC MAIN |
---|---|---|---|
45 | COAXIAL CABLE 1 | 46 | COAXIAL CABLE 2 |
47 | PCBA SUB |
Know your phone
- Front camera
- Volume + key
- Volume – key
- Power key & side fingerprint sensor
- NFC
SIM/SD card installation
- Power off mobile.
- Refer to the following picture for SIM / SD card installation
Charging the phone
You can charge your device using a charger or by connecting it to the computer
using a USB cable (comes with the phone).
Use only INFINIX charger and cables. Other chargers or cables may damage the
device. This will invalidate your phone warranty.
FCC Caution
Labelling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Information to user.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Information to the user.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- ncrease the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information
This mobile phone meets the government’s requirements for exposure to radio
waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluation
of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health. FCC
RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg
averaged over one gram of tissue. Device types: X6832 (FCC ID: 2AIZN-X6832)
has also been tested against this SAR limit. The highest SAR value reported
under this standard during product certification for use at the ear is
1.176W/kg and when properly worn on the body is 0.797W/kg. This device was
tested for typical body-worn operations with the back of the handset kept 10
mm from the body. To maintain compliance with FCC RF exposure requirements,
use accessories that maintain a 10 mm separation distance between the user’s
body and the back of the handset. The use of belt clips, holsters and similar
accessories should not contain metallic components in its assembly. The use of
accessories that does not satisfy these requirements may not comply with FCC
RF exposure requirements, and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.
Operating System:AndroidTM Android is a trademark of Google LLC.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>