DATAKOM DV-0101 Digital Voltmeter Installation Guide

DATAKOM DV-0101 Digital Voltmeter

DV-0101 DIGITAL VOLTMETER – Product Information

Product Specifications|
---|---
Measurement Inputs| 10 – 300 V AC
Accuracy| 0.5% + 1 digit
Power Consumption| < 1.5W
Burden| < 0.1VA per phase
Maximum Humidity| 95% non-condensing
Degree of Protection| IP 54 (Front Panel), IP 30 (Back panel)
Enclosure| Non-flammable, ROHS compliant, high temperature ABS/PC
(UL94-V0)
Installation| Flush mounting with rear retaining brackets
Dimensions| 102x102x53mm (WxHxD)
Panel Cutout Dimensions| 92x92mm
Weight| 185 gr
EU Directives Conformity| 2006/95/EC (low voltage), 2004/108/EC (EMC)
Norms of reference| EN 61010 (safety requirements), EN 61326 (EMC
requirements)

Product Usage Instructions

Precautions for Installation and Safe Use:
Failure to follow the below instructions may result in death or serious injury.

• Before installation, refer to the connection diagram, panel cutout dimensions, and mounting tolerances provided in the user manual.

Installation

The DV-0101 Digital Voltmeter is designed for flush mounting with rear retaining brackets. Follow the steps below for installation:

1. Ensure the power supply is disconnected before installation.
2. Refer to the panel cutout dimensions (92x92mm) to create an appropriate opening in the panel for mounting.
3. Securely attach the rear retaining brackets to the panel.
4. Gently insert the DV-0101 Digital Voltmeter into the panel cutout, ensuring a flush fit.
5. Tighten any screws or fasteners provided to secure the device in place.

Usage
The DV-0101 Digital Voltmeter is designed for accurate measurement of the AC RMS voltage in single-phase systems. Follow the steps below for usage:

1. Ensure the power supply is connected to the appropriate inputs for both supply and measurement.
2. The DV-0101 Digital Voltmeter will display the measured AC RMS voltage in the specified range of 10 – 300 V AC.
3. Read the displayed voltage value on the meter’s digital display.

DV-0101 DIGITAL VOLTMETER 96x96mm SIZES

INTRODUCTION

• These state-of-the-art panel meters are designed for accurate measurement of the AC RMS voltage in single-phase systems.
• Devices have separate inputs for supply and measurement.

PRECAUTIONS FOR INSTALLATION AND SAFE USE

Warning
Failure to follow below instructions will result in death or serious injury

• Do not open the unit. There is no serviceable parts inside.
• Fuses must be connected to the power supply and phase voltage inputs, in close proximity of the unit.
• Fuses must be of fast type (FF) with a maximum rating of 6A.
• Disconnect all power before working on equipment.
• When the unit is connected to the network do not touch terminals.
• Do not try to clean the device with solvent or the like. Only clean with a dry cloth.
• Verify correct terminal connections before applying power.
• Electrical equipment should be serviced only by competent service personnel. No responsibility is assured by the manufacturer or any of its subsidiaries for any consequences arising out of the use of this material.
• Only for front panel flush mounting.

Before installation

• Read the user manual carefully, and determine the correct connection diagram.
• Remove all connectors and mounting brackets from the unit, then pass the unit through the mounting opening.
• Put mounting brackets and tighten. Do not tighten too much, this can brake the enclosure.
• Make electrical connections with connectors removed from sockets, then place connectors to their sockets.
• Note that the power supply terminal is separated from measurement terminals, with a common neutral point.

CONNECTION DIAGRAM

PANEL CUTOUT DIMENSIONS

MOUNTING TOLERANCES

TECHNICAL SPECIFICATIONS

• Power Supply Input:
  • 170 – 275VAC
  • 50 – 60Hz nominal (± 10%)
  • Different AC/DC supply values are available.
• Measurement Inputs: 10 – 300 V AC
• Accuracy: 0.5% + 1 digit
• Power Consumption: < 1.5W
• Burden: < 0.1VA per phase
• Operating Temperature: -40°C to +70 °C
• Maximum Humidity: 95% non-condensing.
• Degree of Protection: IP 54 (Front Panel) IP 30 (Back panel)
• Enclosure: Non-flammable, ROHS compliant, high-temperature ABS/PC (UL94-V0)
• Installation: Flush mounting with rear retaining brackets
• Dimensions : 102x102x53mm (WxHxD)
• Panel Cutout Dimensions : 92x92mm
• Weight : 185 gr

EU Directives Conformity:

• 2006/95/EC (low voltage)
• 2004/108/EC (EMC)

Norms of reference:

• EN 61010 (safety requirements)
• EN 61326 (EMC requirements)

PACKAGING INFORMATION

• Pieces per Package: 12 Pcs
• Package Size: 280 x 170 x 215mm (LxWxH)
• Package Weigh t: 2.5 kg

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>