CONTIXO SC8 Buggy Dual Speed Road Racing RC Car User Manual
- June 13, 2024
- CONTIXO
Table of Contents
CONTIXO SC8 Buggy Dual Speed Road Racing RC Car
Product Information
The Remote Control Racing Car SC8 is a remote-controlled racing car designed for entertainment and fun. It comes in various colors, and the actual product color may vary from what is shown.
Product Usage Instructions
- Before using the SC8, please read the user manual carefully.
- To turn the car on or off, push the switch located on the remote control.
- To adjust the direction of the car, use the Fine Adjuster on the remote control.
- Battery Installation:
- For SC8 Battery Installation:
- Use a small Phillips head screwdriver to remove the battery cover.
- Replace the battery with a new one and ensure it is properly connected.
- Put the battery cover back in place and screw it tightly.
- When removing the battery to charge, unclasp the connector before pulling it off.
- For Remote Battery Installation:
- Follow the instructions provided in the user manual.
- Battery Warnings:
- Follow the safety precautions mentioned in the user manual.
- Use only recommended batteries for the SC8 and remote control.
- If you notice any battery leakage, replace it immediately.
- Battery Charging:
- Ensure the SC8 is turned off before charging.
- Connect the charging cable to the SC8 using the provided cable.
- Plug the other end of the cable into a 5V 1A charger (not included).
- A light indicator will turn on to indicate that the SC8 is charging.
- Leave the SC8 connected to the charger until it is fully charged.
- Unplug the charging cable after charging is complete.
- Recycling:
- Dispose of used batteries according to local regulations and recycling guidelines.
- Charging Time:
- The user manual does not specify the exact charging time. Please refer to the user manual for more information.
SC8 Remote Control
How to Play the SC8
Fine Adjuster: Adjust the direction of the car
Push the switch to turn the car on or off.
Battery Installation
SC8 Battery Installation
- Use a small Philips head screwdriver to remove the battery cover.
- Replace the battery cover and into place.
When removing the battery to charge, to unclasp the connector before pulling it off.
Remote Battery Installation
- Use a small phillips head screwdriver to remove the battery cover.
- Place two Aft:s with the corresponding polarities as labeled on the unit.
- Replace the battery cover and screw back into place.
Battery
Battery Warnings
- There is a certain risk of using lithium batteries, which may cause significant damage to people and property. The end user must use it carefully and bear all the related responsibilities.
- If the battery leaks, avoid contact with skin and eyes. If contact with skin occurs, wash with soap and water immediately. If contact with eyes occurs, rinse immediately with cold water for at least 15 minutes, and seek medical attention.
- If the charger begins to emit a suspicious odor, noise, or smoke, unplug the power supply immediately.
Battery Charging
- The when and turns off when it is fully charged.
- Use only the original factory Do not use damaged or of other brands.
- Do not charge expanded, leaked, or damaged batteries.
- Do not overcharge the battery. When the battery is fully charged, unplug the device.
- Do not charge near inflammable materials (eg. carpets, wood flooring, solid wood furniture, etc.).
- Do not charge the battery immediately after it has become hot.
- The charging temperature of the battery should be between 0-40°C (32-104°F).
Recycling
This equipment consists of electronic components or batteries. For electronic
waste, please dispose of according to local waste disposal laws and
ordinances.
Charging Time
New Battery needs to be fully charged for minutes and use time is up to
minutes.
CONTACT INFORMATION
E-Mail: support@contixo.com
Website: www.contixo.com
©2021 Contixo Inc. All rights reserved. Contixo®, the Contixo logo and
associated characters, trademarks and design elements are owned and
licensed by Contixo Company.