CONTIXO CV2 Remote Control RC Construction Excavator Toy User Manual
- June 13, 2024
- CONTIXO
Table of Contents
CONTIXO CV2 Remote Control RC Construction Excavator Toy
Product Information
The CV2 Remote Control Excavator is a toy engineering vehicle that can be
controlled using a remote control. It comes in various colors and is powered
by batteries. The excavator features a battery-powered motor that allows it to
move and perform realistic
digging actions. The remote control operates on two AA batteries (not
included).
Product Usage Instructions
CV2 Battery Installation:
- Use a small phillips head screwdriver to remove the battery cover.
- Attach the battery to the connector.
- Replace the battery cover and screw it back into place.
Note: When removing the battery for charging, make sure to unclasp the connector before pulling it off.
Remote Battery Installation
- Use a small phillips head screwdriver to remove the battery cover.
- Place two AA batteries (not included) with the corresponding polarities as labeled on the unit.
Guardrail Installation:
To install the guardrail, simply attach it to the corresponding socket on the engineering vehicle.
How to use the Remote Control:
Follow the instructions below to use the remote control:
- Make sure the batteries are installed correctly in the remote control.
- Turn on the power switch located on the excavator.
- Use the buttons on the remote control to control the movement of the excavator (e.g., forward, backward, left, right).
Battery Warnings:
- Batteries must be loaded with the correct corresponding positive and negative electrodes.
- Do not mix old and new batteries.
- Do not mix different types of batteries (types or brands).
Dispose of electronic waste, including the equipment’s electronic components or batteries, according to local waste disposal laws and ordinances.
It is recommended to fully charge the new battery for 240 minutes before using it. The battery can provide up to 25 minutes of usage time.
*product colors may vary
PLEASE READ THIS MANUAL BEFORE USING.
PLEASE RETAIN THIS INFORMATION FOR FUTURE REFERENCE
CV2 Remote Control Excavator Setup
CV2 Battery Installation
- Use a small phillips head screwdriver to remove the battery cover.
- Attach the battery to the connector.
- Replace the battery cover and screw back into place.
*When removing the battery to charge, take care to unclasp the connector before pulling it off.
Remote Battery Installation
- Use a small phillips head screwdriver to remove the battery cover.
- Place two AA’s battery (Not included) with the corresponding polarities as labeled on the unit.
Guardrail Installation
Install the guardrail to the corresponding socket on the engineering
vehicle.Install the guardrail to the corresponding socket on the engineering
vehicle.
How to use the Remote Control
Battery Warnings
- Batteries must be loaded with the right corresponding positive and negative electrodes.
- Do not mix old and new batteries.
- Do not mix different types of batteries (types or brands).
Battery Charging
- The light turns on when charging and turns off when it is fully charged.
- Use only the original factory cable. Do not use damaged or cable of other brands.
- Do not charge expanded, leaked, or damaged batteries.
- Do not overcharge the battery. When the battery is fully charged, unplug the device.
- Do not charge near flammable materials (eg. carpets, wood flooring, solid wood furniture, ets.).
- Do not charge the battery immediately after it has become hot.
- The charging temperature of the battery should be between 0-40°C (32-104°F).
- Recommend using a 5V 1A charger (Not included) for charging.
Recycling
This equipment consists of electronic components or batteries. For electronic waste, please dispose of according to local waste disposal laws and ordinances.
Charging Time
New Battery needs to be fully charged for 240 minutes and use time is up to 25 minutes.
CONTACT INFORMATION
- E-Mail: support@contixo.com
- Website: www.contixo.com
©2021 Contixo Inc. All rights reserved. Contixo®, the Contixo logo and associated characters, trademarks and design elements are owned and licensed by Contixo Company.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>