TARAMPS SMART 5 BASS Power Control System Instruction Manual

TARAMPS SMART 5 BASS Power Control System

Product Information

• Product Name: Taramps Amplifier
• Product Model: Unknown
• Manufacturer: Taramps Electronics LTDA
• Location: Alfredo Marcondes, SP, Brazil
• Product Family: Standard for aftermarket electronic equipment in vehicles
• Power Output: 5000W RMS – Impedance: 0.5 Ohm ~ 2 Ohms
• Frequency Response: 8Hz ~ 200Hz (-3dB)
• Crossover: High Pass and Low Pass Filters
• Bass Boost: Yes – Gain Control: Adjustable
• LED Monitor: Yes
• Protection Features: Thermal Protection, Low Battery Protection

Product Usage Instructions

Installation: – Before starting the installation, ensure that the amplifier is turned off. – Connect the positive and negative power supply cables of the appropriate gauge (2/0 AWG) to the amplifier’s power terminals. – Connect the output cables to the speaker terminals of the amplifier using 7 AWG wire gauge. – Connect the remote cable (18 AWG) to the remote terminal of the amplifier. – Install a protection fuse or circuit breaker with a rating of 230A as close as possible to the batteries. – Ensure that all connections are secure and properly insulated.

Power Supply Polarity: – Check the polarity and never reverse the power supply cables to avoid damaging the amplifier. 3.

Protection Features: – The amplifier has thermal protection, which automatically shuts down the amplifier to prevent overheating. It will restart once it has cooled down. – In case of low battery voltage, the amplifier has a protection feature that will shut it down. When this happens, the red LED on the LED monitor or Smart LEDs will flash 2 times, and the amplifier will restart.

Wire Gauge and Fuse: – It is recommended to use the following wire gauges and fuse for the installation: – Positive/Negative Power Supply Cable: 2 x 2/0 AWG – Output Cables: 7 AWG – Remote Cable: 18 AWG – Protection Fuse or Circuit Breaker: 230A – If the cable length exceeds 4 meters, it is necessary to increase the wire gauge.

Important Notes: – Always follow the instructions provided in the user manual for safe and proper installation. – The product images shown are for illustrative purposes only and may differ from the actual product. – For any further assistance or troubleshooting, refer to the user manual or contact the manufacturer’s customer support.

Term of warranty

TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within
12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.

This warranty excludes:

• Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
• Tamper or torn warranty seal;
• Cases in which the product is not used in adequate conditions;
• Defects caused by accessories, modifications or features attached to the product;
• The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
• Warranty card is not properly filled or torn;
• Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
• Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical assistance

For international support, check on our website: www.taramps.com.br/en/rede- de-assistencias-tecnicas or contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391 E-mail: angelo.assistencia@taramps.com.br

Smart Bass Line Presentation

• Multi-impedance: Featuring new control technology and new functions, the SMART 5 BASS has 5000W RMS rated power in the range of 0.5 to 2 Ohms: (0.5 – 1 – 1.33 – 1.5 – 1.67 and 2 Ohms with same power);
• SMART LEDS: LEDs output signal level indicator on top of product;
• RCA input for up to 4V RMS: Input gain adjustment that allows head units up to 4V RMS output level;
• Dual RCA IN / OUT Input: RCA connector with input and output function, eliminates the needing of “Y” cables for send the same unput signal to another amplifier;
• Power connector for cables up to 2/0 AWG: Allows the use of power cables with larger gauge (up to 70mm²) for higher performance;
• AUTO-Restart Protections: The amplifier automatically restarts after a protection event;
• RAMP audio initialization: After turning on the amplifier, audio is released gradually (ramp).

Introduction

Read this manual before preparing the product. In case of doubt, contact our technical support: (18) 3266-4050 or www.taramps.com.br.

At the end of its useful life, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling center for proper disposal.

Declaration of Conformity

TARAMPS ELECTRONICS LTDA Alfredo Marcondes – SP Brazil

Hereby, Taramps Electronics Ltda declares that the product SMART 5 BASS complies with the Directive 2014/30/EU, according with the following harmonized standard:
-EN 50498:2010 Electromagnetic compatibility (EMC) – Product family standard for aftermarket electronic equipment in vehicles

The full text of the EU Declaration of Conformity is available at the following Product Page on Internet.

Safety requirements

To ensure proper use, please read through this manual before using the amplifier. It is specially important that you know the WARNINGS and CAUTIONS contained here.

• The installation of this amplifier must be done by a qualified professional.
• Wear safety glasses, insulated gloves and correct tools for installing this product.
• This amplifier is for use with 12V batteries. Always check the voltage before installing.
• This amplifier must be installed in a firm place with at least 1” space around the heasink for proper heat spreading.
• Never install the amplifier in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.
• Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating as indicated here in this manual. Use of improper fuse or circuit breaker could result in overheat, smoke, damage to product, injury or burns.
• Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through car’s body.
• Before make any connection to amplifier, disconnect the battery negative terminal.
• When in use, the external surface of may amplifier becomes hot. Avoid touching the heatsink area and keep childrens far from the amplifier.
• This amplifier may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.
• Output connections for speakers may have voltage levels when the amplifier is operating. Make sure that the amplifier is turned OFF before proceed any connection or disconnection in this terminals.
• If you want to dispose this amplifier, don’t throw it on domestic waste. It must be collected by an used electronic product disposal service for proper recycling.

Safety

As you read this manual, pay attention to the safety symbols.

CAUTION
This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage.

Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.

Functions, inputs & outputs

1. IN: Input of signal to be amplified. Connect the to the RCA output of the Head Unit using good shielded cable to avoid noise interference.

2. OUT: Audio signal output. Sends the same input (IN) signal to another amplifier, allowing cascading.

3. GAIN: Adjusts the input sensitivity of the amplifier, allowing a perfect adjustment to the output signal levels of various head units models on the market. It is possible to adjust from 4V (minimum sensitivity) to 0.2V (maximum sensitivity).

4. CROSSOVER

   • HIGH PASS FILTER (HPF): Variable setting from 8Hz to 30Hz, which determines the start of the amplifier’s operating frequency.
   • LOW PASS FILTER (LPF): Variable setting from 60Hz to 200Hz, which determines the end of the amplifier’s operating frequency.

5. BASS BOOST

   • FREQ.: Set the frequency of bass boost from 35Hz to 55Hz.
   • BOOST: Set the boost level from 0 to + 10dB at the frequency set in FREQ.

6. MONITOR: Accessory connection that has the function of monitoring the amplifier, displaying clipping and protection status. (Included accessory).

7. SPEAKER: SPEAKER: Output (positive and negative) for connecting transducers (speakers). Follow the indicated polarity.
   For speaker associations, the impedance to consider is the resulting impedance:

8. TERMINAL REMOTE: It must be connected to the remote output of the head unit using a 18 AWG cable.

CAUTION
Due to the presence of voltage at the output terminals when the product is turned on, avoid contact with them. Risk of electric shock.

Power supply connector

1. 2. SMART COOLER: This amplifier has two internal ventilation fans. For perfect functioning, the amplifier must be installed in a cool and aired place with at least 1” (25mm) space around the heasink for proper heat spreading. The usually working temperature of amplifier is 65°C.
      CAUTION
      The fan and ventilation openings are responsible for cooling the amplifier when it is in use, so it cannot be obstructed.

2. NEGATIVE POWER SUPPLY: Use cable of minimum 2/0 AWG as short as possible, connected to the negative battery pole.

3. POSITIVE POWER SUPPLY: Use cable of minimum 2/0 AWG direct from the positive battery pole, with fuse or circuit breaker (230A), as close to it as possible.
   In order for your amplifier to have the best performance, it is necessary to use all the power inputs. See example on the next page. We recommend that all cables have tinned ends for better electrical contact.
   In case of power bus bar using, avoid tightening with extenders on the allen wrench, as excessive torque may break the the terminal.
   CAUTION
   Before making any connections to the power terminals, make sure that the negative (-) of the vehicle battery is disconnected.

LEDS indicators & protection system

The thermal protection waits for cooling before restarting.
If it goes into protection, the amplifier will automatically restart.

Example:

Low Battery Protection: Working amplifier Red LED (LED Monitor) or Smart LEDS, flashes 2x Red LED (LED monitor) or Smart LEDS, flashes 2× Amplifier restarts.

Installation

CAUTION
CAUTION: All connections to power supply, input and output connectors must be carried out only with amplifier off.

Recommended wire gauge & fuse

• Positive / negative power supply cable __2 x 2/0 AWG
• Output cables wire gauge____7 AWG
• Remote cable _____ 18 AWG
• Protection fuse or circuit breaker____230A
  Calculated considering a maximum length of 4m. Distance greater than this, you will need to increase the cable gauges.

CAUTION
Using wire gauges below the recommendation will result in power loss and overheating of wiring.
Check polarity and never reverse power supply cables due to the risk of damage to the amplifier. It is compulsory to install a protection fuses or circuit breakers as close as possible from batteries.

Examples of connections in the power supply input. Note: Required battery bank capacity: At least 230Ah

CAUTION
This equipment is not suitable for use in places where children may be present.

Technical features

*Rated power with 40Hz sinusoidal signal, THD <= 1%, with resistive loads, measured with SMD/AD-1 audio power analyzer or equivalent and the product at lower than 50°C case temperature and 14.4V supply voltage.
The values as above are typical and may vary, due to electronic components tolerance or manufacturing process.
For further informations or questions, visit our website or contact TARAMPS support.

+55 18 3266-4050
Fabricado por / Manufactured by:
TARAMPS ELECTRONICS LIDA
CNPJ / TAX ID: 11.273.485/0001-03
R. João Silvério, 121 • Res. Manoel Martins
Alfredo Marcondes – SP
Indústria Brasileira – Made in Brazil
www.taramps.com.br

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>