MONOGRAM ZVC48DTB1 48 Inch Custom Brass Hood Installation Guide

June 13, 2024
MONOGRAM

MONOGRAM ZVC48DTB1 48 Inch Custom Brass Hood

Product Information

  • Product Name: 48 Custom Brass Hood ZVC48DTB1
  • Product Name: 48 Custom Stainless Steel Hood ZVC48STSS
  • Manufacturer: MONOGRAM.COM

Product Usage Instructions

  1. Before starting the installation, read the instructions completely and carefully.
  2. It is important to save these instructions for the local inspector’s use.
  3. Observe all governing codes and ordinances during the installation process.
  4. If you are the installer, make sure to leave these instructions with the consumer.
  5. If you are the consumer, keep these instructions with your Owner’s Manual for future reference.
  6. Installation of this appliance requires basic mechanical and electrical skills.
  7. Proper grounding is crucial to avoid the risk of electric shock. If you are unsure about the grounding instructions, consult a qualified electrician.
  8. In case of any damage to the vent hood, contact your dealer.
  9. Due to the weight and size of these vent hoods, and to minimize the risk of personal injury or product damage, it is necessary to have two people for proper installation.
  10. To reduce the risk of fire, follow the provided guidelines for proper installation and maintenance. If you need local service from Monogram, call 800.444.1845. For Monogram Service in Canada, call 800.561.3344. For any additional assistance regarding parts and accessories, contact 800.626.2002.

Safety Information

BEFORE YOU BEGIN
Read these instructions completely and carefully.

  • IMPORTANT Save these instructions for local inspector’s use.
  • IMPORTANT serve all governing codes and ordinances.
  • Note to Installer Be sure to leave these instructions with the Consumer.
  • Note to Consumer Keep these instructions with your Owner’s Manual for future reference.
  • Skill Level Installation of this appliance requires basic mechanical and electrical skills.
  • Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the warranty. See Owner’s Manual for warrantv information.

AWARNING

I Improper grounding can result in a risk of electric shock. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.

  • For Monogram local service in your area, 800.444.1845.
  • For Monogram Service in Canada, call 800.561.3344.
  • For Monogram Parts and Accessories, call 800.626.2002. If you received a damaged vent hood, you should contact your dealer.

ACAUTION

Due to the weight and size of these vent hoods and to reduce the risk of personal injury or damage to the product, TWO PEOPLE ARE

REQUIRED FOR PROPER INSTALLATION.

AWARNING

  • TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
  • Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
  • When cutting or drilling into walls or ceilings, do not damage electrical wiring and other hidden utilities.
  • Ducted systems must always be vented to the outdoors.

ACAUTION

To reduce risk of fire and to properly exhaust air, be sure to duct air outside — do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces or garages.

AWARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORKI

PRODUCT DIMENSIONS

MONOGRAM-ZVC48DTB1-48-Inch-Custom-Brass-Hood-
FIG-1

ADDITIONAL PARTS PROVIDED

These parts are packed with the hood.MONOGRAM-ZVC48DTB1-48-Inch-Custom-
Brass-Hood-FIG-2

TOOLS AND MATERIALS REQUIRED

Not SuppliedMONOGRAM-ZVC48DTB1-48-Inch-Custom-Brass-Hood-
FIG-3

Installation Instructions

INSTALLATION CLEARANCES

This hood is designed to be installed onto a wall. Install this hood 30″ minimum to 36″ maximum above the cooking surface.

In this installation, the ductwork running from the top of the hood will be concealed in the soffit or upper cabinetry.

NOTE Clearances may vary due to type of cooking product and local codes. Check with local inspectors to be sure standard is applicable.

In this installation, the ductwork running from the back of the hood goes directly into the wall.

ADVANCED PLANNING

Ductwork Planning

Carefully review the ductwork installation method as described later in this instruction as well as the hood insert installation instructions.

Wall Framing for Adequate Support

  • This hood is heavy. Adequate structural support must be provided. Hood must be secured to vertical studs in the wall.
  • It is strongly recommended that the hood and hood insert be on site before final framing and wall finishing. This will also help to accurately locate the ductwork  and electrical service.

UNBOXING

MONOGRAM-ZVC48DTB1-48-Inch-Custom-Brass-Hood-FIG-6

STEP 1 DETERMINE HOOD AND DUCTWORK LOCATIONS

MARK LOCATION OF WOOD SUPPORT

  • Use a level to draw a cooktop centerline location. Draw the line to ceiling height.
  • Measure desired distance from the bottom of the hood to the cooking surface, 30″ min. to 36″ max.
  • Use a level to draw a straight horizontal pencil line indicating the bottom of the hood.
  • From the line indicating the bottom of the hood,  measure 16″ up and draw another line for the location  of the top of the wood support.
  • From the line indicating the bottom of the hood,  measure 30″ up and draw another line for the location of the top of the hood. See illustration.

FOR VERTICAL (Straight Up) DUCTING

  • Use a level to draw a centerline from the bottom of the hood to ceiling or soffit.
  • Extend the centerline forward on the ceiling or soffit.
  • Mark the center of a 10-1/2″ hole on the ceiling or soffit by measuring 8-3/4″ from the wall.

MONOGRAM-ZVC48DTB1-48-Inch-Custom-Brass-Hood-FIG-8

FOR DUCTING THROUGH REAR WALL

  • Measure 6-1/2″ above the marked line for the top of the wood support. At the centerline, mark location for a 10-1/2″ diameter hole.

HOUSE WIRING LOCATION

  • House wiring to come through wall as shown. Provide at least 7 feet of house wiring.

MONOGRAM-ZVC48DTB1-48-Inch-Custom-Brass-Hood-FIG-10

STEP 2INSTALL HOOD TO WALL

Mount Wood Support to Wall

  • Locate at least 2 vertical studs at the wood support.

  • Center the supplied wood support, left to right and below the 16″ marked line. Use the center hole in the wood support as guidance.

  • Mark and drill two 3/16″ holes through wood support to match stud locations.

  • Secure the wood support to 2 or more vertical studs, using 2 long, square drive screws.

IMPORTANT : Screws must penetrate at least 1″ into vertical studs. Countersink screws in support.
NOTE : The two supplied mounting screws must remain n their original shipping location. These screws are positioned to engage the keyhole slots in the back of the 1ood.

MONOGRAM-ZVC48DTB1-48-Inch-Custom-Brass-Hood-FIG-13

  • Adjust depth of supplied mounting screws in the wood support until they protrude 1/4″ forward. This 1/4″ gap will provide clearance to hang the hood.

IMPORTANT: Framing must be capable of supporting up to 150 Ibs.

  • Place the hood over the wood support. Be sure the mounting screws engage the keyhole slots in the back of the hood. Tighten the screws. Confirm hood position is correct.

MONOGRAM-ZVC48DTB1-48-Inch-Custom-Brass-Hood-FIG-12

  • Install additional 2 short screws to secure the hood to the wood support.

  • Install 2 medium Phillips screws at top inside of the hood into studs. Chose the appropriate holes that line up with studs.

  • Install 2 medium Phillips screws at bottom inside of hood into studs. Choose the appropriate holes that  line up with studs.

MONOGRAM-ZVC48DTB1-48-Inch-Custom-Brass-Hood-FIG-15

STEP 3 PREPARE CUSTOM HOOD INSERT (UVC9420) FOR INSTALLATION
Refer now to the installation instructions for the Custom Hood Insert (UVC9420) with the following exceptions:

  • Disregard any reference to building a custom wood canopy.
  • For duct planning and electrical planning, you will need to refer to these instructions as some of the dimensions are different.

AWARNING
During Step 2 (Connect Electrical Cables),install the provided ground wire included in this product’s hardware bag.

  • Connect one end of the provided Ground Wire to the Insert Ground Screw in the Insert Junction Box.
  • Be sure that the House Ground Wire and the Hood Ground Wire are both connected to the Insert Ground Screw.
  • Connect the other end of ground wire to one of the 48″ Hood ground holes using the provided green screw.

MONOGRAM-ZVC48DTB1-48-Inch-Custom-Brass-Hood-FIG-16

STEP 4 INSTALL HOOD INSERT INTO HOOD

  • Be sure to follow the remainder of the Custom Hood Insert installation instructions to properly fasten the Insert to the Hood.
  • Be sure to push the Insert firmly up prior to driving the mounting screws. This will prevent any visible gaps hetween the Insert and the Hone

NOTE While performing installations described in this book, safety glasses or goggles should be worn.
NOTE Product improvement is a continuing endeavor at Monogram. Therefore, materials, appearance and specifications are subject to change without notice.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

MONOGRAM User Manuals

Related Manuals