Sonew L08 Omnidirectional Conference Desktop Mic Speakerphone User Manual

L08 Omnidirectional Conference
Desktop Mic Speakerphone
USER MANUAL

Please read the user manual carefully before using.

Connection

Bluetooth connection name: CP_L08_BT USB device name: CP_L08_USB

Operation Guide

machine.
Bluetooth connection| BT light flashes slowly when the machine waits for connection.
BT light stays on when the machine has been connected.
BT light flashes quickly and the machine is put to pairing mode by pressing and holding the button for 2s.
Volume| Press volume+ button to turn volume up while volume light increases.
Press volume- button to turn volume down while volume light decrease.
Mute| Mute/unmute microphone by pressing mute button while red volume light be on/off.
Recording| Start/stop recording by pressing record button while record light flashes/off.
Recording files| Turn on USB drive mode by pressing and hold record button for 2s while record light on.
Turn off USB drive mode by pressing record button whild record light off.
Charging| Orange light on when charging.Green light on when battery life reaches 100%.

Specifications

NOTE

• To ensure better and sustained use of the product, it is recommended to turn on the device at least once within 3 consecutive months, with a boot time of more than 1 hour.
• Do not operate both Bluetooth and USB simultaneously.
• Recorded files cannot been accessed while the device is in a call.
• Please make sure that the device been recognized as an audio device after connecting to the computer via USB cable.
• The device will automatically power off after been idle for more than 30 minutes in Bluetooth connection state.
• Product data is for reference only which based on testing results of Laboratory and the actual product shall prevail!
• Network and environmental factors may potentially impact the performance of device usage. It is recommended to use the device in a well-connected network environment.

After-sales Warranty

Certificate
Date of production:
Examination clerk:

Maintenance Records

Product model| | Purchase date|
---|---|---|---
Maintenance content| Date of maintenance

Warranty Note

Thank you for purchasing our products. All our products follow after-sales service policy of 7-day replacement and 1-year warranty. To ensure your legitimate interests, please read this warranty card carefully and keep it properly.

1. This warranty card is the only certificate for the warranty of the machine.
2. Within 7 days from the date of sale, the machine can be replaced by the same model if there is only a performance failure while the machine itself along with the package are guaranteed to be in good condition.
3.  Within 1 year from the date of sale, the machine follow warranty service policy (excluding human factors) in case of performance failure.
4. The machine exceed 1 year is not covered by this warranty.
5. Accessories are not covered by the warranty.
6. The machine which was dismantled by Non-staff personnel is not covered by the warranty.
7. The machine without a warranty card is not covered by this warranty.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
The devices has been evaluated to meet general RF exposure requirement， the device can be used in portable exposure condition without restriction

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>