TARAMPS EQ Bass Digital Audio Instruction Manual

Instruction Manual

The installation of this product must be made by a qualified professional.

Term of warranty

TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.
This warranty excludes:

• Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
• Tamper or torn warranty seal;
• Cases in which the product is not used in adequate conditions;
• Defects caused by accessories, modifications or features attached to the product;
• The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
• Warranty card is not properly filled or torn;
• Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
• Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical assistance
For international support, check on our website:
www.taramps.com.br/en/rede-de-assistencias- tecnicas or contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br

Introduction

Read this manual before installing the product. In case of questions contact our technical support: +55 (18) 3266-4050 or www.taramps.com.br.
Declaration of Conformity
TARAMPS ELECTRONICS LTDA
Alfredo Marcondes – SP
Brazil
Hereby, Taramps Electronics Ltda declares that the product EQ BASS complies with the Directive 2014/30/EU, according with the following harmonized standard:
-EN 50498:2010
Electromagnetic compatibility (EMC) –
Product family standard for aftermarket electronic equipment in vehicles
The full text of the EU Declaration of Conformity is available at the Product Page on Internet.
At the end of its lifespan, this product must not be disposed of in household waste.
Look for an electronic equipment collection or recycling center for proper disposal.
Safety requirements
To ensure proper use, please read through this manual before using the product. It is specially important that you know the WARNINGS and CAUTIONS contained here.

• The installation of this product must be done by a qualified professional.
• Use the correct tools for installing this product.
• This product is for use with 12V batteries. Always check the voltage before installing.
• This product must be installed in a firm place and away from heat sources.
• Never install the product in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.
• Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating as indicated here in this manual. Use of improper fuse or circuit breaker could result in overheat, smoke, damage to product, injury or burns.
• Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through car’s body.
• Automotive sound systems may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.

Safety
As you read this manual, pay attention to the safety symbols.
CAUTION
This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage.
Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.

Presentation

EQ BASS – Now you can control 100% of your amplifier remotely, through the EQ BASS.
Volume, Bass Boost, High Pass and Low Pass and a Limiter, turning each song into a truly customized sound experience.

Front panel functions

1. LEVEL: Adjusts the input sensitivity of the BASS EQ, which allows for a perfect match the output signal levels of virtually all models of CD/DVD head units on the market. Even 3V input is possible.
2. ON: Indicates that the amplifier connected to the MONITOR is on.
3. CLIP: Indicates that the amplifier connected to the MONITOR is clipping.
4. PROT: Indicates that the amplifier connected to the MONITOR is in protection mode.
5. BOOST: Boost for Sub-bass, with a variable amplitude from 0 to +10dB at the frequency defined in FREQ.
6. FREQUENCY: Determines the Bass Boost acting frequency from 35Hz to 60Hz.
7. SUBSONIC FILTER (HPF): Variable adjustment from 8Hz to 30Hz, which determines the beginning of the amplifier’s operating frequency.
8. LOW PASS FILTER (LPF): Variable adjustment from 60Hz to 250Hz, which determines the end of the amplifier’s operating frequency.
9. LIMITER: Allows you to adjust the output limiter threshold.
10. ON: Indicates that EQ BASS is on.

Rear panel functions

1. NEGATIVE POWER TERMINAL: Use the shortest possible 1.5mm² cable, connected to the negative pole of the battery.
2. REMOTE TERMINAL: It must be connected to the remote output of the CD/DVD player using a 0.75mm² (18 AWG) cable.
3. POSITIVE POWER TERMINAL: Use a 1.5mm² ( 16 AWG) cable straight from the positive terminal of the battery with fuse or circuit breaker (1A) as close as possible to the battery.
4. OUTPUT: Audio signal output. It transmits the signal to the amplifier after passing through the equalizers.
5. MONITOR: Cable connection (Accessory included) that allows monitoring of theamplifier via ON, CLIP and PROT.
6. INPUT: Signal input to be equalized. Connect it to the CD/DVD Player’s RCA output, using a good quality shielded cable to avoid noise pickup.

Connection example

CAUTION
Check power polarity and recommended gauge.
it is recommended to install a 1 Ampere fuse on the positive supply terminal.
Technical features

+18 3266-4050
Manufactured by:
TARAMPS ELECTRONICS LTDA
CNPJ / TAX ID: 11.273.485/0001-03
121 . Res. Manoel Martins
Alfredo Marcondes – SP
Made in Brazil
www.taramps.com.br
MN_017166_R00

References

• Taramps | RED DE ASISTENCIA TÉCNICA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>