TARKETT Homogeneous Sheet Flooring Instructions

TARKETT Homogeneous Sheet Flooring

Product Information

The Homogeneous Sheet Flooring is a high-quality flooring product manufactured by Tarkett. It is designed for indoor use and offers durability and easy maintenance. The flooring is not recommended for exterior use as exposure to excessive UV rays can result in fading, degradation, and/or colour variation. It is important to store and handle the flooring properly to ensure its quality. The rolls must be stored in an indoor, climate-controlled space with a temperature maintained between 65F (18.3C) and 85F (29.4C) and a relative humidity between 40% and 60%. The rolls should be stored vertically, tightly rolled face-out on a sturdy cardboard tube. During installation, it is crucial to protect the flooring from intense or direct sunlight by covering the light source.

Before installation, it is recommended to conduct tests to confirm the suitability of the product for your specific requirements. Tarkett cannot accept responsibility for any loss or damage that may result from processing or working conditions outside their control. When installing the Homogeneous Sheet Flooring, proper subfloor preparation is essential. Concrete subfloors must be constructed and prepared according to the American Concrete Institute’s guidelines and ASTM standards. Wood subfloors must have cross- ventilated space and exposed earth crawl spaces should be sealed with a polyethylene moisture barrier. It is important to note that some resilient flooring products and adhesives may contain asbestos fibres, requiring special handling. Additionally, expansion joints and moving joints in the substrate should not be filled with products not intended for that purpose.

Product Usage Instructions

1. Store the Homogeneous Sheet Flooring in an indoor, climate-controlled space with a temperature between 65F (18.3C) and 85F (29.4C) and a relative humidity between 40% and 60%. Store rolls vertically, tightly rolled face-out on a sturdy cardboard tube.
2. Protect the flooring from intense or direct sunlight during conditioning, installation, and adhesive curing periods by covering the light source.
3. Conduct tests to confirm the suitability of the product for your specific requirements before installation.
4. Ensure proper subfloor preparation, following the guidelines provided by the American Concrete Institute and ASTM standards for concrete and wood subfloors.
5. Do not install the flooring over expansion joints or other moving joints in the substrate. Contact an expansion joint cover manufacturer to meet specific flooring conditions.
6. Test concrete subfloors for moisture and pH (alkalinity) levels. Ensure that the test results do not exceed the limits specified by the adhesive used.
7. For wood subfloors, maintain a minimum of 18 inches (47 cm) of cross-ventilated space between the bottom of the joist and ground. Seal exposed earth in the crawl spaces with a polyethylene moisture barrier.
8. Refer to local and national building codes, as well as ASTM standards, for additional guidelines on subfloor preparation.
9. Handle any resilient flooring products and adhesives containing asbestos fibres with special care and follow proper handling  procedures.

INTRODUCTION

These instructions are written as a guide to be used by professional installers when installing Tarkett products. These instructions, combined with our adhesives and flooring products, create a system. Utilizing this system will ease the installation process and provide the customer with a completed product that will perform its intended purpose. Always visit www.tarkett.com for the most current installation and maintenance instructions. Technical videos and tip sheets are also available. Contact Tarkett Technical Services at (800)-899-8916 with any questions.

HANDLING AND STORAGE

1. All Tarkett products must be stored in an indoor, climate-controlled space and be protected from the elements. Temperature must be maintained between 65F (18.3C) and 85F (29.4C) with a relative humidity between 40% and 60%.
2. Rolls must be stored and secured vertically, tightly rolled face-out on an appropriate sturdy cardboard tube.
3. Tarkett flooring and adhesives must be site-conditioned at room temperature for 48 hours before, during, and after installation. Room temperature must be maintained between 65F (18.3C) and 85F (29.4C) and the ambient relative humidity must be between 40% and 60%. We strongly recommend the permanent HVAC system be fully operating.
   • NOTE : If a system other than the permanent HVAC source is utilized, it must provide proper control of both temperature and humidity to recommended or specific levels for the appropriate time duration as stated above.
4. Once the installation is completed, the service temperature of the space must never fall below 55F (12.8C).
5. In areas that are exposed to intense or direct sunlight, the product must be protected during the conditioning, installation, and adhesive curing periods, by covering the light source.
6. Tarkett products are not recommended for exterior use. Exposure to excessive UV rays can result in fading, degradation, and/or colour variation.
7. The highest quality of materials and workmanship is employed in the manufacturing of Tarkett flooring and careful inspection is made before shipment. A quality installation is the responsibility of the installer. It is the installer’s responsibility to verify the accuracy of the order and to ensure the materials are checked for damage, defects, and satisfactory colour match. An authorized Tarkett distributor or Tarkett representative must be notified of any defects before installation proceeds. Tarkett will not pay for labour or material costs claimed on installed materials with visual defects.
8. Tarkett cannot accept responsibility for any loss or damage that may result due to processing or working conditions and/or workmanship outside our control.
9. Users are advised to confirm the suitability of this product by their tests.

GENERAL SUBFLOOR PREPARATION

1. All subfloors must be permanently dry, clean, smooth, and structurally sound. The surface must be free of all dust, loose particles, solvents, paint, grease, oil, wax, alkali, sealing/curing compounds, old adhesive, and any other foreign material, which could affect the installation and adhesive bond to the substrate. Permanent and non-permanent markers, pens, crayons, paint, or similar marking tools used to mark the substrate, or the back of the resilient flooring material will cause migratory staining. Subfloor contamination or markings that bleed through the flooring material causing discolouration or staining are excluded from the Tarkett Limited Warranty. All substrate contaminants must be mechanically removed before the installation of the flooring material. NOTE: Do not use liquid solvents or adhesive removers. The minimum temperature of the substrate must be 60˚F (15.6 ˚C). The substrate temperature should be a minimum of 5˚F higher than the dew point temperature.
   • Caution : Do not use oil-based sweeping compounds.
   • Fill all depressions, cracks, and other surface irregularities with a good quality cement-based underlayment patching compound appropriate for this purpose.
   • Tarkett does not recommend installing over existing resilient floors. All existing flooring and adhesives must be mechanically removed before installing the new flooring material.
   • Do not use chemical adhesive removers or solvents. Refer to the Resilient Floor Covering Institute’s (RFCI), Recommended Work Practices for Removal of  Existing Resilient Flooring for best work practices.
   • Caution : Some resilient flooring products and adhesives contain “asbestos fibres” and special handling of this material is required.
2. Concrete subfloors must be constructed as recommended by the American Concrete Institute’s ACI 302.2 Guide for Concrete Slabs that Receive Moisture-Sensitive Flooring Materials and prepared by ASTM F 710 Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring. Do not install Tarkett flooring over expansion joints, or other moving joints in the substrate. These joints must be respected and should not be filled with products that are not intended for that purpose. Contact an expansion joint cover manufacturer to meet specific flooring conditions.
   • All concrete subfloors must be tested for moisture and pH (alkalinity):
   • Moisture testing must be conducted by ASTM F 2170 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes or ASTM F 1869 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride. Following ASTM F 2659 Preliminary Evaluation of Comparative Moisture Condition of Concrete, Gypsum Cement and Other Floor Slabs and Screeds Using a Non-destructive Electronic Moisture Meter can provide qualitative information before performing ASTM F 2170 or ASTM F 1869. Acceptable moisture limits can be found in the adhesive section below, on the adhesive label, and in the adhesive specifications online. Test results must not exceed the limits of the adhesive.
   • If the test results exceed the limitations, the installation must not proceed until the problem has been corrected. Tarkett does not recommend or warrant any particular product or procedure for the remediation of high moisture in concrete substrates. Several companies manufacture products suitable for moisture remediation. We suggest you refer to the current ASTM F 710 Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring and ASTM F 3010 Standard Practice for Two-Component Resin Based Membrane-Forming Moisture Mitigation Systems for Use Under Resilient Flooring Systems.
   • A pH test for alkalinity must be conducted. The acceptable pH range of the adhesive can be found in the adhesive section below, on the adhesive label, and in the adhesive specifications online. Results must not exceed the limits of the adhesive. If the test results are not within the acceptable range, the installation must not proceed until the problem has been corrected.
3. Wood subfloors must have a minimum of 18″ (47 cm) of cross-ventilated space between the bottom of the joist and the ground. Exposed earth crawl spaces must be sealed with a polyethylene moisture barrier.
   • Subfloors must meet local and national building codes. Trade associations, such as the APA -The Engineered Wood Association, offer structural guidelines for meeting various code requirements. Refer to ASTM F 1482 Standard Practice for Installation and Preparation of Panel Type Underlayments to receive Resilient Flooring for additional information.
   • Single Floor Wood Construction and Tongue and Groove subfloors must be covered with 1/4″ (6.4 mm) or 1/2″ (13 mm) APA-approved underlayment plywood. Use 1/4″ (6.4 mm) thick underlayment panels for boards with a face width of 3″ (76 mm) or less. For boards wider than 3″ (76 mm) face width use 1/2″ (13 mm) underlayment panels.
   • Countersink nail heads and fill depressions, joints, cracks, gouges, and chipped edges with a good quality Portland cement-based patching compound designed for this purpose.
   • Do not install over OSB (Oriented Strand Board), particle board, chipboard, lauan or composite-type underlayments.
4. Terrazzo and Ceramic floor surfaces must be thoroughly sanded to remove all glaze and waxes. Remove or replace all loose tiles and clean the grout lines. Use a good quality Portland cement-based levelling compound to fill all grout lines and other depressions.
5. Steel floor surfaces must be mechanically abraded to assist with the adhesive bond. The floor must be cleaned to remove all dirt, rust and other contaminants that could affect the adhesive or the bond of the flooring material to the substrate. The surface must be primed with a rust inhibitor. It is important to follow the non-porous installation instructions when installing over metal.
6. Concrete floors equipped with a radiant heating system: Turn the heat down to 65F (18.3C) for at least 48 hours before installation. Heat may be gradually returned to operating temperature 48 hours after installation. Surface temperature must not exceed 85F (29.4).
7. An adhesive bond test must be performed using the actual flooring materials and adhesive to be installed. The test areas must be a minimum of 36″ x 36″ and remain in place for at least 72 hours and then be evaluated for bond strength to the concrete.

INSTALLATION

1. Adhesive Application:

   • See the adhesive chart below and follow the adhesive label instructions for proper use.

2. Sheet Installation Procedure:

   • Install rolls in sequential order following roll numbers on the labels.
   • Reverse sheets.
   • Cut pieces to length allowing approximately 3″ (76 mm) excess for trimming.
   • Cut the first piece to fit by freehand knife, direct scribing or pattern scribing method.
   • Trim 1/2″ (13 mm) off the opposite seam edge using an edge trimmer or straight edge and knife.
   • Position all remaining sheets so that the top sheet overlaps the previous sheet by 3/4″ (19 mm). Trim 1/2″ (13 mm) off opposite the seam edge using an edge trimmer or straight edge and knife.
   • Fold back the sheets apply the adhesive to the substrate and allow proper open time. Open and working times are dependent on the ambient temperature, humidity, substrate porosity and temperature, and air movement. It is the installer’s responsibility to modify the open and working time for job site conditions.
   • When using 975 Two-Part Urethane or 996 Two-Part Epoxy Adhesive the installer MUST work off the flooring or use kneeling boards.
   • Periodically, lift a corner of the sheet to ensure proper transfer of adhesive.
   • Roll the flooring in both directions using a 100-pound three-section roller. (Stay approximately 3″ (76 mm) from the seams.)
   • Recess-scribe the seam to achieve a proper fit.
   • Inspect the floor surface, especially the eams, and remove any adhesive on the surface.
   • Vinyl sheet flooring must be welded using the heat-weld or cold-weld methods listed below.

3. Seams:

   • Heat Weld Seam:
   • NOTE: It is recommended to heat weld seams to provide a sterile and watertight seam.
   • Recess scribe the seam with a slight gap not to exceed 1/64” (0.4mm) to help guide the router.
   • Insert a scrap piece of material under the scribe mark to protect the seam edge of the first piece.
   • Use a sharp knife to cut the seam following the scribe mark. The cut must be perpendicular, do not angle the knife blade.
   • Remove the scrap material and seam trimmings before rolling the seam with a small hand roller.
   • Roll the seam area with a 100-pound three-section roller.
   • Wait a minimum of 24 hours after installation before heat welding the seams.
   • Rout approximately 2/3 of the thickness of the material. Do not route into the foam layer of iQ Optima Acoustiflor.
   • Use Tarkett vinyl weld rod.
   • Cold Weld Seam:
   • NOTE : Aria 2.0, Contract Plus, iQ Granit, Melodia 2.0, and iQ Optima can be cold welded:
   • Recess scribe the seam to provide a net fit.
   • Insert a scrap piece of material under the scribe mark to protect the seam edge of the first piece.
   • Use a sharp knife to cut the seam following the scribe mark. The cut must be perpendicular, do not angle the knife blade.
   • Remove the scrap material and seam trimmings before rolling the seam with a small hand roller.
   • Roll the seam area with a 100-pound three-section roller.
   • Wait at least 2 to 3 hours after the flooring material has been installed before applying the Tarkett Cold Weld Liquid.
   • Refer to the Cold Weld instructions for complete Cold Weld Liquid application details.

4. Flash Coving:

   • Use Tarkett CFS -00-A Cove Filler Strip.
   • Apply 925 Resilient Flooring Adhesive to the wall area using a trowel. Apply RollSmart Fast-Drying Vinyl Flooring Adhesive to the wall area using a paint brush or 3/8” nap paint roller. Net fit the flooring material into the cove cap.
   • Roll the coved material with a small hand roller.

5. Post Installation Floor Protection:
   We recommend that the installation of new flooring material not be performed until all the other trades have completed their work. Proper precautions must be taken during and after the installation process to avoid damage to the newly installed flooring.

   • Immediately after installation:
   • All traffic must be restricted for a minimum of 24 hours after installation. The floor may receive immediate traffic when installing with SpraySmart and RollSmart adhesives.
   • All heavy traffic, rolling loads, pallet jacks, and furniture or appliance placement must be restricted for a minimum of 72 hours after installation.
   • Flooring must be swept or vacuumed to remove loose dirt and grit before the application of proper floor protection. (Do not trap dirt and grit under floor protection.)
   • Apply floor protection suitable for construction foot traffic such as undyed heavy Kraft paper, Ram Board, 1/8” Masonite panels, or similar products designed for resilient floor protection.
   • 72 hours after installation:
   • Areas that will receive heavy traffic, rolling loads, pallet jacks, and furniture or appliance placement must be protected with ¼” thick Masonite or similar wood panels.
   • The floor must be swept or vacuumed before the placement of the floor protection panels. (Lightly damp mop if necessary)

NOTE : Do not use plastic or other non-porous materials to protect the newly installed flooring that could prevent the adhesive from drying properly.

ADHESIVE CLEAN UP
Excess adhesive should be removed during the installation process.

• 925™ Resilient Flooring Adhesive
• 901™ SpraySmart Resilient Flooring Adhesive

RollSmart™ Adhesive

• Use a clean white cloth dampened with water to remove wet adhesive from floor covering and tools.
• Dried adhesive may require the use of denatured alcohol applied to a clean white cloth. (Follow manufacturer’s precautions when using denatured alcohol.)

975™ Two-Part Urethane Adhesive, 996™ Two-Part Epoxy Adhesive

• Before the adhesive sets, remove excess adhesive from the flooring and clean tools with denatured alcohol applied to a clean white cloth. (Follow manufacturer’s precautions when using denatured alcohol.)
• Do not allow the adhesive to dry on the flooring surface.
• Removing dried adhesive may cause irreparable damage to the flooring surface.

MAINTENANCE

1. Wait 72 hours after installation before performing the initial cleaning.
2. A regular maintenance program must be started after the initial cleaning.
3. Refer to Tarkett’s Maintenance Instructions for complete details.

ADHESIVE SELECTION CHART

 |  | Application Porous| and Coverage| Moistu RH%| re / pH L| mits pH| Notes
---|---|---|---|---|---|---|---
Products| Adhesive| Non-Porous| CaCl 2
Aria 3.0 iQ Eminent iQ Granit

iQ Granit SD Granit Safe-T Melodia

iQ Optima

Standard Plus

| 925 Resilient Flooring Adhesive| ****

1/32 x 1/16 x 1/32 U 250 – 300 sq. ft.

per gallon

| ****

1/32 x 1/16 x 1/32 U 250 – 300 sq. ft.

per gallon

| ****

85%

| ****

7 lbs.

| ****

9

| ****

The 925 adhesive is sensitive to substrate porosity. Determine substrate porosity and follow the

adhesive label instructions regarding porous and non-porous substrate

drying times before the installation.

iQ Granit Acoustic iQ Optima Acoustiflor| 1/16 x 1/16 x 1/16 SQ

125 – 150 sq. ft. per gallon

| 1/16 x 1/16 x 1/16 V 150 – 175 sq. ft.

Per gallon

Aria 3.0

iQ Eminent iQ Granit

iQ Granit SD Granit Safe-T Melodia

iQ Optima

Standard Plus

| 975 Two-Part Urethane Adhesive| ****

1/32 x 1/16 x 1/32 U 225 – 250 sq. ft.

per gallon

| ****

1/32 x 1/16 x 1/32 U 225 – 250 sq. ft.

per gallon

| ****

90%

| ****

8 lbs.

| ****

9

| ****

For application in areas subject to heavy point loads, rolling loads, topical moisture, or temperature extremes.

iQ Granit Acoustic iQ Optima

Acoustiflor

| 1/16 x 1/16 x 1/16 V 150 – 175 sq. ft.

Per gallon

| 1/16 x 1/16 x 1/16 V 150 – 175 sq. ft.

Per gallon

Aria 3.0 iQ Eminent iQ Granit

iQ Granit SD Granit Safe-T Melodia

iQ Optima

Standard Plus

| 996 Two-Part Epoxy Adhesive| ****

1/32 x 1/16 x 1/32 U 225 – 250 sq. ft.

per gallon

| ****

1/32 x 1/16 x 1/32 U 225 – 250 sq. ft.

per gallon

| ****

90%

| ****

8 lbs.

| ****

9

| ****

For application in areas subject to heavy point loads, rolling loads, topical moisture, or temperature extremes.

iQ Granit Acoustic

iQ Optima Acoustiflor

| 1/16 x 1/16 x 1/16 V

150 – 175 sq. ft.

Per gallon

| 1/16 x 1/16 x 1/16 V

150 – 175 sq. ft.

Per gallon

iQ Granit Acoustic iQ Optima Acoustiflor

| 901 SpraySmart Resilient Flooring Adhesive| ****

150 sq. ft. per can 900 sq. ft. per carton

| ****

150 sq. ft. per can 900 sq. ft. per carton

| 90%| 8 lbs.| 10| The SpraySmart Adhesive System is unique; instructions must be followed. Contact Tarkett Technical Department before use for training.
Aria 3.0 iQ Eminent iQ Granit

iQ Granit SD Granit Safe-T Melodia

iQ Optima

Standard Plus

| RollSmart Adhesive| ****

3/8″ Nap Paint Roller (used with a paint tray)

350 – 400 sq. ft. per gallon

| ****

3/8″ Nap Paint Roller (used with a paint tray)

350 – 400 sq. ft. per gallon

| 95%| 8 lbs.| 10|
Aria 3.0

iQ Eminent iQ Granit

iQ Granit SD Granit Safe-T Melodia

iQ Optima

Standard Plus

| Cold Weld Liquid| 4.5 oz. tube 175 – 200 in. ft. per tube| 4.5 oz. tube 175 – 200 in. ft. per tube| N/A| N/A| N/A|

Tarkett North America
Technical Services Department 30000 Aurora Road Solon, OH 44139 800.899.8916 Fax 440.632.5643 info@tarkettna.com www.tarkett.com

References

• Home - Tarkett Commercial
• Home - Tarkett Commercial

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>