TARAMPS PRO 2.6S Free Shipping Worldwide Instruction Manual

Instruction Manual

The installation of this product must be made by a qualified professional.

Team of warranty

TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19.180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.
This warranty excludes:

• Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
• Tamper or torn warranty seal;
• Cases in which the product is not used in adequate conditions;
• Defects caused by accessories, modifications or features attached to the product;
• The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
• Warranty card is not properly filled or torn;
• Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
• Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical assistance

For international support, check on our website: www.taramps.com.br/en /rede-de-assistencias-tecnicas or contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br

Introduction

Read this manual before installing the product. In case of questions contact our technical support: +55 (18) 3266-4050 or www.taramps.com.br.

Declaration of Conformity
**** TARAMPS ELECTRONICS LTDA
Alfredo Marcondes – SP
Brazil Hereby, Taramps Electronics Ltda declares that the product PRO 2.6S complies with the Directive 2014/30/EU, according with the following harmonized standard: -EN 50498:2010 Electromagnetic compatibility (EMC) – Product family standard for aftermarket electronic equipment in vehicles The full text of the EU Declaration of Conformity is available at the Product Page on Internet.
At the end of its lifespan, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling center for proper disposal.

Safety requirements
To ensure proper use, please read through this manual before using the processor. It is specially important that you know the WARNINGS and CAUTIONS contained here.
– The installation of this product must be done by a qualified professional.
– Use the correct tools for installing this product.
– This product is for use with 12V batteries. Always check the voltage before installing.
– Never install the product in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.
– Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating as indicated here in this manual. Use of improper fuse or circuit breaker could result in overheat, smoke, damage to product, injury or burns.
– Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through car’s body.
– Automotive sound systems may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.
Key recommendations
The wire gauge for power supply connections is 1,5mm² (15 AWG) for positive and negative
wires, and 0,50mm² (20 AWG) for remote signal wire.
For protection against overload, install a fuse on positive wire, close to battery terminal (1A). See
page 12.

1. Power supply negative: Connect to negative pole of battery.
2. Remote signal input: Connect to remote signal output from head unit.
3. Remote ouput: For connection in amplifiers
4. Powe supply positive: Connect to positive pole (12V) of battery.

Safety
As you read this manual, pay attention to the safety symbols.
This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage.
CAUTION
Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.

Processor overview

Screens & basic operation:
After startup, the main screen will appears. The blue LEDs for each output way show the active outputs.

Turning the rotary encoder knob (clockwise or counterclockwise), adjusts the master volume (Input volume).

A short press at the rotary encoder center access the Main Menu and its functions. Along press, back to previous menu. Keep pressed to back to main screen.

Menu & parameters navigation
Use the Rotary encoder, turn it clockwise (increment) or conter clockwise (decrement). The menu selection, option or parameter selection could be done pressing the encoder button (center—short press).
Note: In any audio adjust screen, the OUTx Keys allows to check and adjust the parameters for each way without quit from desired option.

Menu structure & Description

Press the encoder button (center — long press) to back to Main Screen.
1- Audio menu: Adjusts and controls related to audio processing:

-1/0 Routing: Sets the internal connections between the 2 inputs and 6 output. Available options: A, B or A+B (The sum of 2 inputs). As example, if define CH1 -> A, this output CH1 will process the signal coming frominput A.

~Crossover: Set the high pass (HPF) and low pass (LPF) filters of selected output way. The cutoff frequencies could be set from 20Hz to 20KHz, and are available some kinds of filters (Butterworth,
Bessel, Linkwitz Rilley) in different slopes (-6,-12,-18 and -24dB/Octave).

Delay: Set the delay to be applied to audio signal, for systems alignment. The position of transducer’s voice coil should be taken in account in order to set the optimal delay value.

Turn the Rotary encoder to’set the delay amount to be applied.
The voice coils of each transducers isn’t aligned inside the acoustic box, so there is some delay that can degrade the perfect audio playing. The Delay feature apply different delay amount for each output way, in order to get the perfect audio alignment.
How to set the delay parameter value (centimeter):

1. Set the reference voice coil (the most far point from acoustic box front panel)
2. Measure other transducers in order to define the A measure. Ajust the delay parameter as close as possible.
3. Repeat the procedure above for other ways. The selection of output ways is done pressing the OUTx (1to6) Keys.

-Phase: Inverts the output signal if select the [180] option Selectthe desired way using the OUTx (1to 6) Keys. Turn the Rotary encoder to choose O degree or 180 degrees.

~Limiter: Define the limiter, limiting the maximum signal level at processor’s outputs, in order to don’texceed the loudspeakers maximum power rating.
Modes: OFF: (disabled) / ON: Limiter enabled / AUT: Load optimal Attack and Release parameters, based on HPF frequency. Parameters:
T=Threshold: Set the point for limiter starts the gain reduction;
A= Attack: Set the time before limiter perform the gain reduction after the signal reach the threshold level;
R = Release: Set the time before limiter back to normal gain, after the audio signal back to a level bellow the threshold.

-Outputlevel: Set the level for each output way. Allow apply up to 648 gain or -24dB attenuation.
Select the desired way using the OUTx (1-6) Keys.

Note: This fuction s available at the main screen, just pressing the desired OUTx (1-6) Key.
-Output parametric EQ: Parametric equalizer with 3 band for each output way.
Parameters:
EQ1 – EQ3: Select 3 band available peak filters;
G = Gain or attenuation of selected band (-12dB to +12dB)
F = Center frequency of selected filter
Q= Parameter Q (bandwidth) of selected filter.

-Mirroring: Adjust the selected output way using the other way’s parameter, cloning an already configured way.

3-)Language: Choose the desired language (Portuguese, English or Spanish)
4-) save config: Save the current configuration into memory. 3 positions are available for save the user custom parameters.
5-) Load config: Load a previous saved configuration or load the factory settings.
Note: Ifyou need restore the factory settings due to password lost, keep pressed the CH1 and CH2 keys + encoder button while power on the audio processor and select YES. (This procedure will erase all parameters previously saved).
6-) Password / lock: Lock the processor by a 4 digit security password (default password = 1234) and allows change the security password to another custom password.
When the PRO 2.6 is locked, appears an icon on main screen right top corner.
Note: If you need restore the factory settings due to password lost, keep pressed the CH1 and CH2 keys + encoder button while power on the audio processor and select YES. (This procedure will erase all parameters previously saved).

Input & Output Connections

CAUTION
Checkpower polarity and recommended gauge. itisrecommendedtoinstallal Amperefuseon the positive supply terminal,

Technical features

Input & Output:
Input channels:………………………………………………2
Output channels:………………………………………………………6
Rou, B, A+B
Master level:……………………………………………………-80 ~ 0dB
Output level:…………………………………………………………..-24 ~ +6dB
Input impedance:…………………………………………18K ohms
Output impedance:………………………………………………47 ohms
Maximum input level:…………………………………………..6Vpp (2.1V RMS)
Maximum output level:………………………………………………….10.2Vpp (3.6V RMS)
Frequency response(-1dB ±0,5):……………………………………………….10Hz ~ 20KHz
Total Harmonic Distor…………………………………0.01%
Signal-to-noise Ra………………………………………….>90dB
Crosstalk:………………………………………………………>80dB
Crossover / X-over (HPF / LPF):
Frequency cutoff:………………………………………………….20Hz ~ 20KHz
Filters Linkwitz Rilley:……………………………………………-12, -24dB/oct
Filters Buerworth:……………………………………………………..-6,-12,-18, -24dB/oct
Filters Bessel:…………………………………………………..-12,-18, -24dB/oct
Delay:…………………………………………………………..5.7mS (194cm)
Phase:………………………………………………………………………….0 / 180°
Adjustable limiter:
Threshold:………………………………………………………………-24 ~ 0dB
Aack:………………………………………………………….1ms ~ 900ms
Release:…………………………………………………………..1ms ~ 4000ms
3 Band Parametric EQ:
Center Frequency:………………………………………….20Hz ~ 20KHz
Aenua-12dB ~ +12dB
Q factor:………………………………………………………………..0.4 ~ 10
Adjust mirroring Mute for each output Sinusoidal Audio Generator
Frequency Range:……………………………………………..20Hz ~ 20KHz
Gain:……………………………………………………………-60 ~ 0dB
Languages:…………………………………………………… Portuguese – English – Spanish
Memory posi………………………………………………………….3 + Factory default
Access protec……………………………………………………………..4 digit password
Voltage Range:……………………………………………………………………………9 ~ 16VDC
Nominal Consump
Dimensions (WxHxD):………………………210 x 43 x 122mm / 8.27” x 1.69” x 4.80”
Weight:………………………………………………………………….0,550Kg / 1.21lb
Taramps reserves the right to modify the contents of this document at any without prior noand does not have the obligato apply the changes in units which were previously produced.

+5518 3266-4050
Fabricado por / Manufactured by:
TARAMPS ELECTRONICS LTDA
CNPJ/ TAXID: 11.273.485/0001-03
R Jodo Silvério, 121+ Res. Manoel Martins
Alfredo Marcondes – SP
Indiistria Brasileira – Made in Brazil
www.taramps.com.br

Documents / Resources

| TARAMPS PRO 2.6S Free Shipping Worldwide [pdf] Instruction Manual
PRO 2.6S Free Shipping Worldwide, PRO 2.6S, Free Shipping Worldwide, Shipping Worldwide, Worldwide
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>