Altronix Pace1PRD IP and Hi-PoE Receiver over Extended Distance CAT5e Installation Guide
- June 4, 2024
- Altronix
Table of Contents
Pace1PRD IP and Hi-PoE Receiver over Extended Distance CAT5e
**Installation Guide
**
Pace1PRD
IP and Hi-PoE Receiver over extended distance CAT5e
Installation Guide
Overview:
Pace1PRD is a long-range Ethernet receiver that transmits data at 100Mbps full duplex and power via a CAT5e or higher cable. The Pace1PRD receiver is powered via the Altronix NetWay1D midspan injector. The receiver passes the Hi-PoE (60W) power over the cable to the eBridge200WPM transceiver which, in turn, passes this power to an enabled IP camera/device. These plug-and-play units facilitate cost-effective solutions for IP devices that need to be installed at distances greater than 100m.
Features:
Agency Listings:
- UL/cUL Listed for Information Technology Equipment (UL 60950-1).
- CE European Conformity.
Input:
- Powered by NetWay1D (60W).
Ethernet:
- Connectivity: RJ45, auto-crossover.
- Wire type: 4-pair CAT5 structured cable.
- Distance: up to 500m.
- Speed: 10/100BaseT, half/full duplex, auto negotiation.
- Throughput is rated to pass 100Mbps of data at distances up to 500m. With proper headend equipment, this supports Megapixel, HD720, and HD1080.
CAT5e or Higher:
- Distance: up to 500m @ 100Mbps (see Cable Type, Total Device Power, Data and Power Distance, pg. 3).
LED Indicators:
- Green – PoE ON (by respective RJ45 jack).
- Yellow and Green LED IP Link status, 10/100Base-T/active.
Environmental:
- Operating Temperature: 20ºC to 49ºC ( 4ºF to 120.2ºF).
- Storage Temperature: 30ºC to 70ºC ( 22ºF to 158ºF).
- Humidity: 20 to 85%, non-condensing.
Functions:
- Auto detection and protection of legacy non-PoE cameras/devices.
Applications:
- Extend Network link distance in an industrial environment (see note, pg. 2).
- Works with Megapixel, HD720, HD1080 and VGA (SD) cameras (see a note, pg. 2).
Mechanical:
- Dimensions (W x L x H approx.): 3.5″ x 3.5″ x 1″ (88.9mm x 88.9mm x 25.4mm).
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application. Pace1PRD is intended for indoor use only.
-
Pace1PRD Installation:
a. Secure the unit to the desired mounting surface with a proper fastening device utilizing the unit’s mounting hole (Fig. 2a, pg. 3). Unit should be mounted in proximity to an ethernet switch/network, NVR or video server.
b. Connect the structured cable from NetWay1D to RJ45 jack marked [PoE Input] (Fig. 2, pg. 3).
c. CAT5e or higher: Connect CAT5e or higher cable to connector marked [RJ45 Link] (Fig. 2, pg. 3). -
eBridge200WPM Connections:
a. Connect CAT5e from Pace1PRD (60W) to the connector marked [CAT INPUT] (Fig. 2, pg. 3)
b. Select input power SW3 on the switch marked [60W CAT, 30W CAT, or 60W COAX] (Fig. 2, pg. 3).
c. Connect the structured cable from one (1) 60W camera/device to the RJ45 jack marked [Port 1] or connect two (2) individual structured cables from two (2) 30W cameras/devices to RJ45 jacks marked [Port 1] & [Port 2] (Fig. 2, pg. 3).
Technical Specifications:
| Parameter | Description |
|---|---|
| Connections | RJ45 for ethernet link. |
| Input Power Requirements | 60W from Midspan or endspan port connected. PoE |
compliant to IEEE 802.3af (15W) and
PoE+ compliant to IEEE 802.3at (30W), Hi-PoE (60W)
Indicators| Yellow (RJ45 connector): On-Link, Off – No Link, Blinking –
Activity.
Green (RJ45 connector): On – 100Base-TX, Off – 10Base-T.
Green: PoE Active.
Environmental Conditions| Operating Ambient Temperature (UL60950-1):
— 20°C to 49°C (— 4°F to 120.2°F).
Relative humidity: 20 to 85%, non-condensing.
Storage Temperature: — 30°C to 70°C (— 22°F to 158°F).
Operating Altitude: — 304.8 to 2,000m.
Regulatory Compliance| UUcUL Listed for Information Technology Equipment (UL
60950-1). CE European Conformity.
Weights (approx.)| Product: 3.88 oz. (0.11 kg.) I Shipping: 6.70 oz. (0.19
kg.)
*Note Caution: once the Hi-PoE connection is established between Pace1PRD and eBridge200WPM, disconnection from eBridge200WPM will not disable the Hi- PoE output voltage on the Pace1PRD, although the eBridge200WPM can be reconnected, caution should be taken not to connect the CAT5e wiring from Pace1PRD to any non-PoE device.
Single PoE Camera Connection:
Cable Type, Total Device Power, Data and Power Distance:
Cable Type| Total Power Consumption| Max. Data Distance|
Max. Power Distance
---|---|---|---
CAT5e| 15W| 500m| 500m
CAT5e| 30W| 500m| 423m
CAT5e| 60W| 500m| 211m
Note: Higher gauge wiring will allow for longer distances.
Notes:
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA
phone: 718-567-8181
fax: 718-567-9056
website: www.altronix.com
e-mail: info@altronix.com
Lifetime Warranty
IIPace1PRD Rev. 0116151
Pace1PRD Installation Guide
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>