HINKLEY 99058FMW Matte White Facet Downrod Mount Kit Instruction Manual

**HINKLEY 99058FMW Matte White Facet Downrod Mount Kit Instruction Manual

**

PARTS

A) Mounting coupler assembly

B) Hanger bracket

C) Canopy

D) Canopy cover

E) Donwood Asm

F) Yoke cover

INSTALLING THE HANGER BRACKET

REMEMBER – Turn off the power !

Attach hanging bracket to outlet box using screws provided with the outlet box. **(Fig.1)

**

HANGING THE FAN

Step 1. Remove hanger ball from downrod byloosening set screw in the side of the hanger ball. Slide hanger ball down and remove cross pin; remove hanger ball. (Fig. 2)

Step 2. Carefully support the fan motor assembly in it’s styrofoam packing so the top of the motor facing upward

Step 3. Slip the wires from the fan motor through the mounting coupler assembly, and than tighten mounting coupler assembly to the fan body with four mounting screws. (Fig. 3)

Step 4. Carefully feed the electrical lead wires and safety cable from the fan through the dowered. Thread dowered into coupler until holes align. Insert downrod pin through holes in mounting coupler and dowered; clip cotter pin through small hole in end of dowered pin to hold downrod in place. **(Fig. 4)

**

Step 5. Tighten security set screws against downrod using a large flat blade screwdriver to ensure a tight fit against downrod.

Step 6. Slip the wires from the fan motor through the yoke cover and canopy cover and canopy onto the downrod. Slide the hanger ball onto the downrod, insert the cross pin through the downrod. Pull thehanger ball up so the cross pin seats in the channel in the hanger ball. Tighten the set screw. **(Fig. 5)

**

Step 1. Attach the wood screw and the flat washer to the ceiling joist as shown (do not fully tighten). Slide the  cable clamp onto the safety cable from the fan. Loop the safety cable around the wood screw that was just attached to ceiling joist. Feed the end of the cable into the clamp and pull as much cable through as possible. Firmly tighten screw in the clamp. Cut off excess cable and tighten the wood screw to ceiling joist. (Fig.6)

ELECTRICAL CONNECTIONS

WARNINGS: Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire nuts, except for the ground wire.

Step 1. Insert the receiver into the mounting bracket.

Step 2. Make wire connections from the fan to the receiver unit. For this step use the bundle of 5 wires on the receiver. **(Fig.7)

**

• Connect the YELLOW fan wire to the YELLOW receiver wire.
• Connect the GRAY fan wire to the GRAY receiver wire.
• Connect the RED fan neutral wire to the RED receiver neutral wire.
• Connect the WHITE neutral light kit lead from the fan to WHITE receiver lead marked “ For Light”.
• Connect the BLUE light kit lead from the fan to BLUE receiver lead marked “For Light”

Wire colors out of the fan are blue/white for the light kit. Light kit leads from the controller/receiver are blue/white.

Step 3. Connect the supply wires from the ceiling to the receiver unit. (Use the 2 wire bundle on the receiver) Secure with supplied wire nuts.

• Connect the BLACK building supply wire to the BLACK receiver wire.
• Connect the WHITE receiver neutral wire to the WHITE building neutral wire.
• Connect the COPPER building ground wire to the 4 YELLOW/ GREEN ground wires from the fan and receiver

FINISHING THE INSTALLATION

Step 1. Tuck connections neatly into ceiling outlet box. (Fig. 8)

Step 2. Remove one canopy screw on the bracket and slide the canopy up to mounting bracket and place the key hole on screw on the mounting bracket aligning the key slot in the canopy with the canopy screw in the hanger bracket, turn canopy until it locks in place at the narrow section of the key holes.

Step 3. Align the remaining circular slot in the canopy with the threaded hole in the hanger bracket. Install canopy screw loosely. Rotate the canopy in the slots to align the points of the canopy with points of the fan housing. Securely tighten both canopy screws.

Step 4. Assemble the canopy cover by aligning the two key slots on the top side of the canopy cover with the two canopy screws. Twist to lock into place.

Referring to Facet fan installation instruction for other ceiling fan installing procedure.

Documents / Resources

| HINKLEY 99058FMW Matte White Facet Downrod Mount Kit [pdf] Instruction Manual
99058FMW Matte White Facet Downrod Mount Kit, 99058FMW, Matte White Facet Downrod Mount Kit, Facet Downrod Mount Kit, Downrod Mount Kit, Mount Kit
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>