VISUAL COMFORT CHC 5879 Large Wrapped Lantern Instruction Manual

VISUAL COMFORT CHC 5879 Large Wrapped Lantern

Product Information

• Product Name: Darlana Large Wrapped Lantern
• Item Number: CHC 5879

Product Description: The Darlana Large Wrapped Lantern is a light fixture designed for installation in accordance with applicable local installation codes. It features a durable construction and is suitable for both indoor and outdoor use. Please read and follow the assembly instructions carefully before installation.

ASSEMBLY INSTRUCTIONS

Darlana Large Wrapped Lantern

• Item # CHC 5879

NOTICE

• This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect items and contents carefully. If any damage or defect is found, do not install it.
• Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED)

• Phillips Screwdriver
• Slotted Screwdriver
• Chain Pliers
• Slip Joint Pliers
• Measuring Tape
• Wire Cutters
• Wire Strippers

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Install mounting plate (B) to the junction box and secure it with mounting screws (C).

3. Secure collar loop (D) to mounting plate (B) using pliers to tighten the locknut.

4. Install canopy (E) to collar loop (D) and secure with collar ring (F).

5. Thread rods (M) to the bottom frame (N), then slide tubes (K) over rods (M) and rest on the bottom frame (N).

6. Install the top fixture frame (J) to the top of the rods (M) and secure with screws (Q) and threaded caps (P).

7. Determine the desired overall length, and amount of chain (H) needed. Shorten the chain using chain pliers. (Keep extra chain)

8. Attach chain (H) to collar loop (D) and fixture loop (I) using quick links (G). Secure quick links (G).

9. Hang fixture cluster (O) to hook on the bottom of fixture loop (I), then pass fixture wires through the hole in fixture frame.

10. Thread fixture wire and ground wire through the chain (H).
    NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.

11. Separate two sides of molded wire, and strip insulation on each 5/8″.

12. Loosen collar ring (F) and let canopy (E) slip down chain (H) carefully.

13. Twist all fixture wires together, and slip through center hole of the collar loop (D).
    NOTE: Untwist wires and separate them to prepare for connection.

14. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A).
    NOTE: It is imperative that the fixture is grounded.

15. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).

16. Connect the fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A).
    CAUTION: Do not reverse the hot and neutral connections.

17. Make sure all wire connections are tight, then carefully tuck into the junction box.

18. Install canopy (E) to collar loop (D) and secure with collar ring (F).

19. Install light bulbs into the sockets.

Darlana Large Wrapped Lantern

• Item # CHC 5879

NOTICE

This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect items and contents carefully. If any damage or defect is found, do not install it. Retain all packaging material until installation is complete and approved.

Care Instructions

• Clean only with a soft dry cloth or feather duster. Do
• Do not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>