ROLL-N-LOCK M-Series Tonneau Cover Instruction Manual

: June 13, 2024
: ROLL-N-LOCK

Table of Contents

ROLL-N-LOCK M-Series Tonneau Cover
Product Information
Product Usage Instructions
STANDARD AND XT SERIES
TOOLS PROVIDED
PARTS INCLUDED IN YOUR KIT
INSTALLATION INSTRUCTION
LIMITED WARRANTY
COVER CARE AND MAINTENANCE
USE
SAFETY INSTRUCTIONS
TROUBLESHOOTING TIPS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ROLL-N-LOCK M-Series Tonneau Cover

ROLL-N-LOCK-M-Series-Tonneau-Cover-product

Product Information

The product is the M-Series A-Series Standard and XT Series for the 2014-2018 Silverado/Sierra 1500 and the 2015-2019 Silverado/Sierra 2500/3500. It is a bed cover for trucks that provides protection and security for the cargo area.
The installation process is the same for both the standard track and XT Series track, except that the tailgate extrusion is not used with the XT Series.
The product kit includes various parts such as housing, tracks, cargo shield, tailgate extrusion (not used with XT Series), drain tube, housing bracket, CB track bracket, bed clamp, threaded tang, cargo nut, butyl caulk strip, shim, bolts, screws, rubber washers, lid screws (taped to lid), NT striker plate (not used for XT series track install), and hook latch cap (not used for XT series track install).

Product Usage Instructions

If there is no plastic bedliner, proceed with step 1B. Otherwise, remove the bedliner by cutting across the bulkhead (cab) from the passenger to the driver’s side and cutting out both driver and passenger side pieces using the measurements provided. Use a jig saw to cut out the liner parts and discard them. Then drill five 1/2-inch holes where indicated and reinstall the bedliner.
If there is a tie-down in the first hole near the cab on both the driver and passenger side, remove them and move them to the second hole location toward the tailgate.
Assemble the housing bracket (F) to the threaded tang (I) using a 1/4-20 x 1 bolt (M) and flat washer (N). Level and tighten the bracket on the passenger side using a 7/16 wrench. Stick the butyl caulk strip (K) over the top end of the housing bracket. Repeat on the driver’s side.
Centre the housing (A) between the bed rails and against the bulkhead on both the driver and passenger side.
Remove the lid from the housing by pushing it toward the cab and up on both the driver and passenger side.
Assemble the CB track bracket (G) to the threaded tang (I) using a 1/4-20 x 1 bolt (M) and flat washer (N). Remove the hole plug from the stake hole pocket and insert the CB track bracket in the hole. Loosely attach it on both the driver and passenger side.
Turn the lock to 10 o’clock without removing the plastic wing nut. Align the tracks (B) onto the housing stem and make sure the edge of the tracks butt up against the housing on both driver and passenger side.
Secure the tracks to the housing stem on both driver and passenger side using the cargo nut (J) and #10-24 screw (S) with a Phillips screwdriver.

STANDARD AND XT SERIES

NOTE: Installation is the same for both the standard track and the XT Series track.
NOTE: Tailgate extrusion is NOT used with XT Series.

NOTE: It is important that all areas where the bed cover mounts are clean and free of debris prior to installation.

TOOLS PROVIDED

1/4” Allen wrench
3/16” Allen wrench
303® Vinyl protector

TOOLS REQUIRED

Jig saw
1/2” drill bit
Drill with Phillips’s head
Phillips screwdriver
7/16” Wrench
Tape measure

PARTS INCLUDED IN YOUR KIT

A 1x Housing
B 2x Track
C 1x Cargo shield
D 1x Tailgate extrusion
E 2x Drain tube
F 2x Housing bracket
G 2x CB track bracket
H 4x CM bed clamp (6x 8’2”ft Bed)
I 4x Threaded tang
J 2x Cargo nut
K 2x Butyl caulk strip
L 4x Shim
M 4x 1/4-20 x 1” Bolt
N 4x 1/4” Flat washer
O 4x 5/16” Socket cap screw (6x 8’2”ft Bed)
P 4x 5/16” Lock washer (6x 8’2”ft Bed)
Q 2x 1/4” Socket cap screw
R 2x 1/4” Lock washer
S 2x #10-24 Screw
T 7x #8 x 3/4” Self tapping screw
U 4x 1/4-20 x 3/8” Screw
V 4x Black rubber washer
W 2x 1/4” Lid screw (Taped to lid)
X 2x NT striker plate
Y 2x Hook latch cap
Not used for XT series track install

INSTALLATION INSTRUCTION

If there is No plastic bedliner proceed with step 1B.
Remove the bedliner. 1. Using a tape measure with the measurements given, cut across the bulkhead (cab) from the passenger to the driver’s side. 2. Use the measurements on the tailgate end to cut out both driver and passenger side pieces. 3.
Then use a jig saw to cut the liner parts out. Discard cut parts. 4.
Drill (5) 1/2” holes where indicated.
Reinstall the bedliner
If there is a tie-down (1) in the first hole near the cab on the driver and passenger side, remove both and move them to the second hole location toward the tailgate.
Assemble the housing bracket (F) to the threaded tang (I) using a 1/4-20 x1” bolt (M), and flat washer (N). Then level and tighten on the passenger side with a 7/16” wrench (1). Stick the butyl caulk strip (K) over the top end of the housing bracket as shown. Repeat on the driver’s side.
Centre the housing (A) between the bed rails, and up against the bulkhead on the driver and passenger sides.
Remove lid from housing (A) by pushing toward cab (1) and up (2) on the driver and passenger sides.
Assemble the CB track bracket (G) to the threaded tang (I) using a 1/4-20 x1” bolt (M), and 1/4” flat washer (N). Remove hole plug (1) from stake hole pocket to install CB Track bracket (G). Insert CB track bracket (G) in a hole and loosely attach it on the driver and passenger side.
IF NOT INSTALLING THE XT SERIES TRACK PROCEED TO STEP 10B.
USE THIS STEP ONLY IF YOU DO NOT INSTALL TAILGATE EXTRUSION (D) – (1) Remove the existing standard striker plate from the tailgate end of track (B) on driver and passenger side by removing the 2 screws with a Phillips head screwdriver and set them aside. (Do not discard). (2) Then install the new NT striker plate (X) using the 2 screws you saved. Then repeat on the passenger side track (B). (3) Remove the hook latch from housing (A) on the driver and passenger side. (4&5) Install hook latch caps (Y) in place of hook latches.
(1) Turn lock to 10 o’clock. (Do not remove plastic wing nuts). (2) Align tracks (B) onto the housing stem. (3) Make sure the edge of the tracks butt up against the housing on the driver and passenger side.
Secure tracks (B) to housing stem (1) on the driver and passenger side using cargo nut (J) and #10-24 screw (S) using a Phillips screwdriver (2).
Loosely attach the CB track bracket (G) to the pre-installed 9B track clamps with 1/4” lock washer (R) and 1/4” socket cap screw (Q).
Loosely attach CM bed clamps (H) to the pre-installed track clamps using a 5/16” socket cap screw (O) and 5/16” lock washer (P) on the driver and passenger side.
IF NOT INSTALLING THE XT SERIES TRACK PROCEED TO STEP 10B. USE TO INSTALL OPTIONAL TAILGATE EXTRUSION – Then mark on the tailgate protector (2) where to cut and take it off the tailgate to cut it. Discard cut parts. Replace the tailgate protector.
IF NOT INSTALLING THE SERIES TRACK PROCEED TO STEP 10B. USE TO INSTALL OPTIONAL TAILGATE EXTRUSION – (1) Holding the tailgate extrusion (D) assembly in place carefully. Holding the tailgate assembly square to the tailgate, use five (5) #8 x 3/4” self-tapping screw (T) to secure the centre hole, move to each end, press the assembly to the top of the tailgate making it conform to the contour of the tailgate, and secure it in place.
IF NOT INSTALLING THE XT SERIES TRACK PROCEED TO STEP 10B. USE TO INSTALL OPTIONAL TAILGATE EXTRUSION – Close the tailgate, shift the housing (A) back so the end of the tracks (B) are up against the tailgate on driver and passenger sides.
Close the tailgate, and shift the housing (A) back to the end of the tracks (B) are up against the tailgate on driver and passenger side.
Once tracks (B) are correctly spaced and adjusted to the correct height, tighten backtrack bracket (G) with a fastener (Q) using a 3/16” Allen wrench (1) and fastener (M) using a 7/16” wrench (2) on driver and passenger side. If needed use shims (L) in the back of bracket (G) to bring track (B) to the 90o position.
Tighten CM bed clamps (H) to the pre-installed track clamps using a 1/4” Allen wrench on driver and passenger side.
Note: When tight there may be a gap between the clamps, do not over-tighten.
Turn the lock to 7 o’clock (1), remove the plastic wing nut (2) and using both hands pull the cover back to the tailgate. Screw housing (A) into housing bracket (F) (3) with self-tapping screw (T) on driver and passenger side. (Discard plastic wing nut).
Replace lid on housing (A) by lining up the pin with the slot and pushing down (1) and toward tailgate (2) on the driver and passenger sides. Then install the 1/4” lid screws (W) with a Phillips screwdriver (3) on driver and passenger side.
To open cover pull back on the handle, turn the lock (1 & 2) to 10 o’clock and let the cover retract into the housing (A) while holding onto the pull strap (3).
Note: Remove the protective backing from the cargo shield (C) first. Attach cargo shield (C) with the slots at the bottom of the housing (A) using two black rubber washers (V) and two 1/4-20×3/8” screws (U) on the driver and passenger side.
Drill 1/2” hole (1) through the bulkhead as shown. DO NOT drill through the truck cab. Insert one end of the drain tube (E) through the drilled 1/2” hole feed toward the ground and insert the other end onto the housing fitting.
Make sure the drain tubes (E) are NOT aligned with or through the cab vents (1) on the driver and passenger side.
Note: Rust protection should be used on the holes you drilled.
Attach the pull strap to the truck’s rear driver or passenger side rear tie-down towards the tailgate.

IMPORTANT NOTICE

This bed cover may retract to the full open position very quickly resulting in any objects placed on top of the bed cover to fall off the bed cover or becoming trapped inside of the bed cover carrier. Do not place ANY objects on top of the bed cover when attempting to close.
Failure to follow the instructions may result in damage to your vehicle, belongings or bed cover. To avoid injury keep all body parts clear of the bed cover and carrier when opening.

LIMITED WARRANTY

WARRANTY COVERAGE

This truck bed cover is warrantied against defects in materials or workmanship as follows.
This warranty is void if the product has been damaged in an accident, or due to neglect, unforeseeable use, improper installation, improper servicing, or other cause not arising out of defects in material or workmanship.
The truck bed covers carry a limited warranty for three (3) years from the original date of purchase, subject to the terms below.

WARRANTY IS NOT TRANSFERABLE

The warranty is to the initial consumer purchasing the truck bed cover and it is not transferrable to a subsequent end user. Proof of purchase may be required to enforce these warranty rights.

WARRANTY CONDITIONS

Failure to follow these care and use instructions will void the warranty:
Clean with mild automotive soap and water only. Do not use any strong chemicals or cleaners. Lubrication of the rails with silicone or petroleum-based products will void the warranty.
Cargo must be secured at all points when the vehicle is in motion. Failure to adequately secure the cover or tether strap can result in damage and will void the warranty.
Check all clamps and retention mechanisms for tightness after a week of driving following installation (or re-installation) of the cover and periodically thereafter.
Before opening, the cover must be free of all foreign materials including snow and ice.
Do NOT tow your vehicle from the rear with the cover on your vehicle. If towing from the rear is required, the cover MUST be removed from the vehicle and properly stored.
WARRANTY PERFORMANCE
If all warranty conditions are met, a defective truck bed cover or hardware component will either be repaired or replaced (at our option). We reserve the right, for any warranty, to substitute a newer model or bed cover having a similar form and function, to offer a warranty discount on an entire replacement system, and/or to provide remedies other than those mentioned in this document.

WARRANTY RETURN

A Return Material Authorization number must be obtained from our Customer Service Department prior to returning any product. We may require the original item to be returned postage prepaid for final determination. Shipping charges will apply for any repair or replacement. Other than postage or shipping charges, no charge will be made for repair or replacement under this warranty.
This warranty gives you specific legal rights. As a consumer, you may also have additional rights and remedies under the laws of your state.
Register online at https://rollnlock.com/warranty-registration

REGISTER YOUR WARRANTY ONLINE

COVER CARE AND MAINTENANCE

Vinyl Tops

Clean with mild automotive soap and water only. Do NOT use any strong chemicals or cleaners.
Do NOT use conditioners that contain silicone or petroleum (e.g. Armor All®).
We recommend using 303 Aerospace Protectant® to prolong the life of the vinyl.

Hard Tops

Clean with mild automotive soap and water only. Do NOT use any strong chemicals or cleaners. the use of wax or polish is not recommended.

Maintenance

It is recommended that you periodically check that the cover is securely attached to your truck bed. Inspect the clamps and front mounting bolts to ensure they were properly installed and have not come loose or knocked out of adjustment during operation. Covers that are used with high frequency or that are subject to vibrations and impact from rough roadways can cause the cover to require adjustment.
IMPORTANT: NEVER spray any lubricant into the tracks. THIS WILL VOID YOUR WARRANTY. Lubricants, especially silicone or petroleum-based, will attract dirt and debris which will lead to slow operation and will degrade the gaskets over time. If the tracks feel a little ‘sticky’, you may spray some 303 Aerospace Protectant® inside the track and wipe with a clean rag to remove any dirt or debris that has built up.

Housing Drains

To ensure proper drainage, it is recommended that the canister housing be checked and cleared of any leaves, twigs or other debris that may obstruct the drain tubes.
To remove the lid, first, make sure the Roll-N-Lock cover is fully closed and securely latched at the tailgate. Remove the Phillips head screw on each side of the lid and slide the lid slightly forward toward the cab to disengage the set pins. Once free, the lid can be lifted and removed from the canister. DO NOT ALLOW THE COVER TO RETRACT WITH THE LID REMOVED. This could allow the cover to retract too far into the canister causing damage to the cover.

USE

Opening and Using the Cover

Grasp the handle with one hand and pull it towards the tailgate to relieve pressure on the latches. At the same time, turn the tear-drop lock from the 7 o’clock latched position to the 10 o’clock unlatched position. Release the handle and the cover should begin to retract. The cover may require a slight push to get it started retracting. The tether strap can be used to control the speed of the cover as it retracts. Allow the cover to retract fully into the lid and this will reset the tear-drop lock to the 7 o’clock position.
Closing and Locking the Cover
Using the tether strap, gently pull the cover toward the tailgate. Once the cover handle is within reach, grasp with both hands, and pull the cover closed until it latches into place making sure that the tear-drop lock is pointed at the 7 o’clock position. Secure the tether strap inside the truck bed when latching. Forcing or slamming the cover back may damage the truck or cover.
Never close the cover with the tear-drop lock pointed at 10 o’clock as the latches will not engage properly. Always close the cover body with the tear-drop lock pointed at 7 o’clock. Failure to close the cover body correctly will result in the unit not latching.

SAFETY INSTRUCTIONS

DO NOT place objects on or against the cover or framework.
DO NOT tie cargo to the truck bed cover framework.
DO NOT operate the vehicle with objects on top of the cover body.
NEVER allow children or pets to occupy the truck bed while the cover is closed.
The cover is not airtight. Special care is required to keep cargo clean and dry.
Bed covers won’t prevent theft of contents inside the truck box.