VISUAL COMFORT CHC 5877 Medium Wrapped Lantern Instruction Manual

VISUAL COMFORT CHC 5877 Medium Wrapped Lantern

Product Information:

• Product Name: Darlana Medium Wrapped Lantern
• Item Number: CHC 5877
• Bulbs: Not included
• Product Description: The Darlana Medium Wrapped Lantern is a light fixture that requires assembly and installation. It should be installed in accordance with all applicable local installation codes and by a person familiar with its construction and operation, as well as the hazards involved. The product comes with a mounting plate, collar loop, canopy, rods, tubes, top fixture frame, chain, quick links, and fixture wires.

Product Usage Instructions

1. Carefully remove all parts from the box and place them on a clean, soft surface.

2. Install the mounting plate (B) to the junction box using the provided mounting screws (C).

3. Secure the collar loop (D) to the mounting plate (B) using pliers to tighten the locknut.

4. Attach the canopy (E) to the collar loop (D) and secure it with the collar ring (F).

5. Thread the rods (M) to the bottom frame (N) and slide the tubes
   (K) over the rods (M) to rest on the bottom frame (N). Install the top fixture frame (J) to the top of the rods (M) and secure it with screws (Q) and threaded caps (P).

6. Determine the desired overall length and amount of chain (H) needed. Shorten the chain using chain pliers, while keeping extra chain for future use.

7. Attach the chain (H) to the collar loop (D) and fixture loop (I) using the quick links (G). Secure the quick links (G).

8. Hang the fixture cluster (J) to the hook on the bottom of the fixture loop (I), and then pass the fixture wires through the hole in the fixture frame.

9. Thread the fixture wire and ground wire through the chain (H).

10. When reaching the collar loop (D), ensure there is no tension on the wires. Cut any excess wires, making sure to leave enough length to reach the junction box.

11. Separate the two sides of the molded wire and strip insulation on each 5/8 inch.

12. Loosen the collar ring (F) and carefully let the canopy (E) slip down the chain (H).

13. Twist all fixture wires together and slip them through the center hole of the collar.

Care Instructions: Clean the product only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Darlana Medium Wrapped Lantern
Item # CHC 5877

NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED)

• Phillips Screwdriver
• Slip Joint Pliers
• Wire Strippers
• Slotted Screwdriver
• Measuring Tape
• Chain Pliers
• Wire Cutters

ASSEMBLY INSTRUCTIONS

1.  Carefully remove all parts from the box. Place on a clean, soft surface.

2.  Install mounting plate (B) to the junction box and secure with mounting screws (C).

3. Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut.

4. Install canopy (E) to collar loop (D) and secure with collar ring (F).

5. Thread rods (M) to the bottom frame (N), then slide tubes (K) over rods (M) and rest on bottom frame (N).

6. Install top fixture frame (J) to the top of the rods (M) and secure with screws (Q) and threaded caps (P).

7. Determine desired overall length, and amount of chain (H) needed. Shorten chain using chain pliers. (Keep extra chain)

8. Attach chain (H) to collar loop (D) and fixture loop (I) using quick links (G). Secure quick links (G).

9. Hang fixture cluster (J) to hook on bottom of fixture loop (I), then pass fixture wires through the hole in fixture frame.

10. Thread fixture wire and ground wire through chain (H).
    NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.

11. Separate two sides of molded wire, and strip insulation on each 5/8″.

12. Loosen collar ring (F) and let canopy (E) slip down chain (H) carefully.

13. Twist all fixture wires together, and slip through center hole of collar loop (D).
    NOTE: Untwist wires and separate to prepare for connection.

14. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A).
    NOTE: It is imperative that the fixture is grounded.

15. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).

16. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A).
    CAUTION: Do not reverse the hot and neutral connections.

17. Make sure all wire connections are tight, then carefully tuck into the junction box.

18. Install canopy (E) to collar loop (D) and secure with collar ring (F).

19. Install light bulbs into the sockets.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>