COUNTRYLINE CL-30P-DDF Tractor Supply Co. County Line Floor Fan Instruction Manual

COUNTRYLINE CL-30P-DDF Tractor Supply Co. County Line Floor Fan Instruction Manual

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT: Read and understand all of the directions in this manual before assembling, starting, or servicing the fan. Improper use of this fan can cause serious injury. Keep this manual for future reference.

WARNING For ventilating use only. Do not use to exhaust hazardous chemicals or use near any flammable liquids or gases as sparks from motor may ignite fumes. Never use the fan in spaces which contain products such as gasoline, solvents, paint thinners, dust particles, volatile or airborne combustibles, or any unknown chemicals.

This product meets and exceeds the requirements of OSHA 1910.212(a)(5), the standard which regulates electric fan blade safety, and is certified under UL# E234000, established and made effective April 10, 2003, and updated March 23, 2005, by Underwriters Laboratories, Inc.

Please note the serial number of your fan, and write it on the back of this User’s Manual for future reference.

Distributed by: TRACTOR SUPPLY COMPANY 200 POWELL PLACE BRENTWOOD, TN 37027

For customer support, call: 1-866-641-4540

IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY, SERVICE OR USE OF THIS FAN. FAILURE TO COMPLY WITH THESE INSTRUCTIONS COULD RESULT INSERIOUS PERSONAL INJURY AND / OR PROPERTY DAMAGE

If safety guards have been removed to service or maintain this fan, reinstall or remount the safety guards as previously installed.

WARNING
This unit is designed for indoor use only. Do not expose to elements or allow to become wet.

WARNING
To guard against electric shock while operating, do not allow fan to come in contact with other grounded objects such as pipes, radiators, etc.

WARNING
Risk of fire, electric shock, or personal injury when performing service or maintenance. Unplug or disconnect the fan from the power supply before servicing.

WARNING
To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any Solid- State Speed Control Device.

WARNING
To Reduce The Risk Of Electric Shock And Injury To Persons, Do Not Use In a Window.

WARNING
For General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors

WARNING
DO NOT MOVE FAN WHILE OPERATING! MOVING FAN DURING OPERATING CAN CAUSE BLADE DAMAGE

• Turn off, unplug unit, and wait for fan to stop before moving, storing, and / or changing operating locations.
• Operate only on 115 volt 60 Hz (cycle) current with a minimum of a 15 amp circuit.
• Before operating always check fan for loose or damaged parts. Inspect power cord for any damage. Never use fan if any parts are damaged or missing. Never use fan without safety guards attached.
• When used with an extension cord, use only cord of proper size (Amp rating), UL listed, and with receptacle to accept three prong grounded plug furnished on the fan’s power cord. Always keep power cord and extension cords away from heat, oil, and sharp edges. Inspect cords periodically and replace if damaged.
• Disconnect fan from power source when not in use, before servicing and when cleaning or repairing.
• Repair of this appliance should be done by a qualified electrician.
• In case of power failure, turn fan off at knob or power chain to prevent unexpected restarting and component damage.
• Keep children away from fan at all times.

20” FLOOR FAN

Installation and Assembly (requires Phillips head screwdriver)

WARNING
If the Wall Mount Kit is applied, the installer MUST be certain that the support bracket is mounted to a minimum of a 2×4” stud, and that it is able to support 50 pounds continuously.

1. Remove 1 screw from each Frame Support L and R (Items 7 and 19).
2. Slide Frame Support L and Frame Support R into Support Frame (Item 21) and line up holes for screw.
3. Re-attach screw to Frame Support L and Frame Support R.

Exploded View

Replacement Parts

Installation and Assembly – Floor

Locate fan in safe, desired position on level ground, and connect to approved power source.

Exploded View

Replacement Parts

24” BARREL FAN

Installation and Assembly – Wall Mount (requires flat head screwdriver)

WARNING If the Wall Mount Kit is applied, the installer MUST be certain that the Wall Mount is mounted to a minimum of a 2×4” stud, and that it is able to support 50 pounds continuously

1. Attach Wall Mount (item 17 on page 4) to wood stud as shown below.
2. Slide Wall Bracket L and Wall Bracket R on Large Base (item 23) onto Wall Mount.

Figure 3: Wall Mount installation

30” PEDESTAL FAN

Installation and Assembly

REQUIRED TOOLS:

• Pliers
• Knife
• Phillips head screwdriver
• Flat head screwdriver
• 10mm / adjustable wrench
• 6mm hex wrench (included)

PARTS INCLUDED IN BOX:

• Rubber Base Ring
• Base
• Front Grille
• Rear Grille
• Motor Assembly
• Fan Blade Assembly
• Spring
• Support Pole Assembly

1. Attach Rubber Base Ring (item 16 on page 7) to outer edge of Base (item 15). Be sure ribbed side of Base Ring is facing down.

2. Remove 5 screws from Flange on bottom of Lower Support Pole (item 16).

3. Completely extend Upper Support Pole (item 21) from Lower Support Pole and insert Spring into bottom of Lower Support Pole.

4. Attach Support Pole Assembly to Base. Tighten hardware using star parttern to insure a tight, uniform fit.

5. Stand assembly on Base, and press down Upper Support Pole and then tighten Height Adjustment Knob (item 3).

6. Attach Motor Support Assembly to Motor Assembly (see figure 5).

7.  Place Motor Support into Upper Support Pole.|
   – Insert Pivot Bolt and tighten.
   
   

8. Remove 4 screws on motor, and attach the Rear Grille. Tighten screws only after all 4 screws are reattached to the motor.

9. Remove the screws on the Motor and attach the Rear Grille onto groove in motor shaft, and replace screws (See figure 4).

10. Loosen the set screw on the back of the Fan Blade Assembly and slide onto the motor shaft.
    CAUTION Do NOT slide fan blade screw beyond the groove on the shaft!
    This will cause the fan blade to not spin properly and can cause damage to your fan! Be sure that fan shaft is flush with front of fan blade assembly

11. Position set screw over flat groove on motor shaft and tighten set screw using 6mm hex wrench (included). Be sure set screw is on the groove, and the front of Fan Blade Assembly is flush with front of shaft before tightening.

12. Attach Front Grille by first aligning the top hooks of the Front Grille onto the top of the Rear Grille edge. Work your way around the grille, placing the Front Grille hooks over the Rear Grille edge. If necessary, use a flat head screwdriver to help pry the Front Grille hooks over the Rear Grille edge. Continue until all hooks are completely attached to the Rear Grille edge.
    Figure 5: Attaching Motor to Motor Support Assembly
    

30” PEDESTAL FAN

Exploded View

Replacement Parts

FLOOR FAN -OPTIONAL CEILING MOUNT

Exploded View

Replacement Parts

Floor Installation

Simply locate fan in safe, desired position on level ground, and connect to approved power source.

Ceiling Mount Installation

WARNING The installer MUST be certain that the ceiling that the mounting bracket is mounted to is able to support 100 pounds continuously.

MOUNTING BRACKET INSTALLATION:

1. Remove Wheel Frame (item 15 on page 8).
2. Attach Cart Frame to Ceiling beam using U-bolts (item 5 on page 10).
3. Assemble and attach Ceiling Mount Assembly as shown in figure 10 on page 10.

NOTE: This fan uses a folding wheel design. For quick assembly, simply swing the wheels out and snap to lock in place.

SAFETY CABLE INSTALLATION:

1. After the fan is securely mounted, feed the safety cable between one of the swivel brackets as shown in figure 8.
2. Pull safety cable through and secure cable with safety cable U-bolt as shown in figure 9.
3. Take other end of cable and wrap around beam
4. Secure cable loop as shown in step 2. Be sure there is approximately 2 inches of slack in the safety cable once both ends are secured.
5. Repeat on other side of fan so there are two safety cables.

Ceiling Kit Exploded View

Ceiling Kit Replacement Parts

Troubleshooting Guide

unit isplugged in and turned on.
2. Bad motor| Replace motor
Reduced Air Flow| 1. Obstruction| Turn off and unplug fan. Remove guard and make surenothing is obstructing the fan blades.
2. Bad switch or capacitor| Replace switch or capacitor (Note: To prolong life offan, operate fan first in 1(LOW) for 5-10 seconds before switching to higher speed.
Humming sound but nooperation| 1. Bad capacitor| Replace capacitor
Excess Noise (vibration,squealing)| 1. Fan is not on level ground| Turn off fan, and move unit to smooth level surface.
2. Guard is not secure| Check guard screws to be sure all are tight.

1 YEAR LIMITED WARRANTY

The manufacturer warrants this product to the original retail purchaser only, to be free from defects in material and workmanship for a period of one (1) year from the date of initial purchase. This product must be properly installed, maintained and operated in accordance with the instructions provided.

The manufacturer requires reasonable proof of your date of purchase from an authorized retailer or distributor. Therefore, you should keep your sales slip, invoice, or cancelled check from the original purchase. This Limited Warranty shall be limited to the repair or replacement of parts, which prove defective under normal use and service within the warranty period, and which the manufacturer shall determine at its reasonable discretion.

This warranty does not apply to products purchased for rental use.

This Limited Warranty does not cover any failures or operating difficulties due to normal wear and tear, accident, abuse, misuse, alteration, misapplication, improper installation or improper maintenance and service by you or any third party. Failure to perform normal and routine maintenance on the fan, shipping damage, damage related to insects, birds, or animals of any kind, and damage due to weather conditions are also not covered. In addition, the Limited Warranty does not cover damage to the finish, such as scratches, dents, discoloration, rust or other weather damage, after purchase.

All transportation costs for the return of the damaged product or parts will be the responsibility of the purchaser. Upon receipt of damaged item, the manufacturer will examine the item and determine if defective. the manufacturer will repair or replace and return the item, freight pre-paid.

If the manufacturer finds the item to be in normal operating condition, or not defective, the item will be returned freight collect.
This Limited Warranty is in lieu of all other express warranties. The manufacturer disclaims all warranties for products that are purchased from sellers other than authorized retailers or distributors.
AFTER THE PERIOD OF THE ONE (1) YEAR LIMITED WARRANTY EXPIRES, THE MANUFACTURER DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR APPLICATION. FURTHER, THE MANUFACTURER SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. The manufacturer assumes no responsibility for any defects caused by third parties. This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other rights depending upon where he or she lives. Some states do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above exclusion and limitations may not apply to you.

The manufacturer does not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return, or replacement of its equipment, and no such representations are binding on The manufacturer.
Always be sure to specify model number and serial number when making any claim with the manufacturer.

ALWAYS BE SURE TO SPECIFY MODEL NUMBER AND SERIAL NUMBER WHEN MAKING ANY CLAIM WITH THE MANUFACTURER. FOR YOUR CONVENIENCE USE THE SPACE PROVIDED BELOW TO LIST THIS INFORMATION:

Model #: ____ Serial #: __
Date of Purchase: _____

HVF Air Circulator User’s Manual
For customer support, call 1-866-641-4540
www.TractorSupply.com

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>