BASS 5K Taramps Module Amplifier Instruction Manual

BASS 5K Taramps Module Amplifier

Product Information

• Product Name: BASS 5K
• Manufacturer: TARAMPS ELECTRONICS LTDA
• Product Family: Standard for aftermarket electronic equipment in vehicles
• Warranty: This product is covered by a warranty provided by TARAMPS ELECTRONICS LTDA. Please refer to the warranty terms and conditions for more information.

Features

• Input: Hz

• Level: 0 MAX 8

• Subsonic Filter: 30Hz – 60Hz

• LPF Freq.: 35Hz – 250Hz

• Bass Boost: 0dB – +10dB

• Crossover: 1 OHM, 2 OHMS, 4 OHMS

• Coolers: This amplifier has two internal coolers for optimal
  functioning.

• Sensitivity of Input (Level 100%): 220mV >95dB

• Crossover HPF (Subsonic Filter): 8Hz – 250Hz (-3dB)

• LPF (Low Pass Filter): 35Hz – 60Hz

• Bass Boost Frequency: 35Hz – 60Hz

• Bass Boost Boost: 0dB – +10dB

• Consumption at Rest: 1.20A

• Musical Consumption @14.4VDC: 209A (1 Ohm), 418A (2 Ohms)

• Dimensions: 239mm x 73mm x 327mm

• Weight: 5Kg

Product Usage Instructions

1. Coolers: This amplifier has two internal coolers for optimal functioning. Ensure that the coolers are not obstructed and that there is proper airflow around the amplifier.
2. Input: Connect the input source to the amplifier using the recommended input cables.
3. Sensitivity of Input: Adjust the sensitivity of the input level according to your preference. The range is from 0 to 8.
4. Subsonic Filter (Crossover HPF): Set the subsonic filter frequency range between 30Hz and 60Hz to eliminate low-frequency signals that may cause distortion or damage to the speakers.
5. Low Pass Filter (LPF): Set the low pass filter frequency range between 35Hz and 250Hz to control the high-frequency output of the amplifier.
6. Bass Boost: Adjust the bass boost frequency and boost level according to your preference. The frequency range is from 35Hz to 60Hz, and the boost level can be set between 0dB and +10 dB.
7. Crossover: Select the appropriate crossover impedance (1 OHM, 2 OHMS, or 4 OHMS) based on your speaker configuration.
8. Power Supply: Connect the amplifier to a power source within the recommended voltage range (9VDC – 17VDC).
9. Consumption: Take note of the power consumption of the amplifier. The consumption at rest is 1.20A, and the musical consumption at 14.4VDC is 209A (1 Ohm) or 418A (2 Ohm).
10. Dimensions and Weight: The amplifier has dimensions of 239mm x 73mm x 327mm and weighs 5Kg.

Introduction

Read this manual before preparing the product. In case of doubt, contact our technical support: (18) 3266-4050 or www.taramps.com.br.
At the end of its useful life, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling center for proper disposal.

Safety requirements

To ensure proper use, please read through this manual before using the amplifier. It is especially important that you know the WARNINGS and CAUTIONS contained here.

• The installation of this amplifier must be done by a qualified professional.
• Wear safety glasses, insulated gloves, and correct tools for installing this product.
• This amplifier is for use with 12V batteries. Always check the voltage before installing.
• This amplifier must be installed in a firm place with at least 1” space around the heatsink for proper heat spreading.
• Never install the amplifier in places exposed to dust, humidity, and water. Pay attention to installing it far from the fuel tank, fuel lines, heat sources,, and other parts of the vehicle.
• Be sure to install a protection fuse or a circuit breaker near to the battery. Follow the ampere rating as indicated here in this manual. Use of an improper fuse or circuit breaker could result in overheating, smoke, damage to the product, injury, or burns.
• Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through the car’s body.
• Before making any connection to the amplifier, disconnect the battery negative terminal.
• When in use, the external surface of may amplifier becomes hot. Avoid touching the heatsink area and keep children far from the amplifier.
• This amplifier may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.
• Output connections for speakers may have voltage levels when the amplifier is operating. Make sure that the amplifier is turned OFF before proceeding with any connection or disconnection in these terminals.
• If you want to dispose of this amplifier, don’t throw it on domestic waste. It must be collected by a used electronic product disposal service for proper recycling.

Safety As you read this manual, pay attention to the safety symbols.

CAUTION: This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in a risk of injury to the user or product damage.

Functions, inputs & outputs

1. INPUT (R and L): Inputs of signals to be amplified. Connect these signals to the RCA outputs of the Head Unit, using good quality shielded cables to avoid noise influence.
2. LEVEL: It sets the amplifier input sensitivity, which allows an optimal adjustment to the output signal levels of nearly all models of the Head Unit found in the market.
3. CROSSOVER
4. FILTRO SUBSONIC (HPF): Variable adjustment from 8Hz to 30Hz, which determines the beginning of the amplifier operating frequency.
5. LOW PASS: Variable adjustment from 60Hz to 250Hz, which determines the end of the amplifier operating frequency.
6. BASS BOOST
7. FREQ.: Set the Bass Boost center frequency, from 35Hz up to 60Hz.
8. BOOST: Boost for bass levels in 50Hz, with variable gain up 0 to +10dB.
9. MONITOR: Connection to an accessory, whose function is to monitor the amplifier and it is where all information from the indicator LEDs, such as distortion (CLIP) and protection actuation (PROT), will be displayed simultaneously.
10. SPEAKER: Output (positive and negative) to transducer connection (speakers). Follow the polarity described and the minimum impedance recommended.
    To combine speakers, the resulting impedance must be taken into consideration.
    See the examples below:

CAUTION: Due to the presence of voltage at the output terminals when the product is turned on, avoid contact with them. Risk of electric shock.
REMOTE TERMINAL: The remote Head Unit output must be connected by a 0,75mm² (18 AWG) cable.

Power supply connector

1. FANS: This amplifier has two internal ventilation fans. For perfect functioning, the amplifier must be installed in a cool and aired place with at least 1” (25mm) space around the heatsink for proper heat spreading. The usually working temperature of amplifier is 65°C.
   CAUTION:  The fan and ventilation openings are responsible for cooling the amplifier when it is in use, so it cannot be obstructed.

2. POSITIVE POWER SUPPLY TERMINAL: Use a 2/0 AWG (70mm²) cable directly from the positive battery terminal with fuse (210A), as close as possible from the battery.

3. REMOTE TERMINAL: The remote Head Unit output must be connected by a 0,75mm² (18 AWG) cable.

4. NEGATIVE POWER SUPPLY TERMINAL: A 2/0 AWG (70mm²) cable as short as possible must be used, connected to the negative battery pole.
   It is recommended that all cables must have tinned ends to improve electrical contact.

CAUTION: Before making any connections to the power terminals, make sure that the negative of the vehicle battery is disconnected.

LEDS indicators & protection system

Blue LED steady on:
Indicates that the amplifier is turned on.

Flashing yellow LED: Excessive temperature (May be caused by obstruction of the internal fans, improper installation or poorly ventilated location).

• When the amplifier reaches the temperature of approximately 80°C (176°F), the thermal protection starts working, the audio is interrupted and the yellow LED will start flashing. The fans will be functioning, in order to cool down the components quickly.
• Only when the amplifier reaches a safe temperature level, the audio is released and the amplifier gets back to its normal functioning.
• We recommend don’t turn off the amplifier, so that the cooling time will be shorter, through the ventilation of fans.
• Blinking yellow LED according to music: Indicates that the amplifier is operating at the threshold of distortion. If the red LED also blinks, it indicates excessive distortion.

Red LED steady on:
Short-circuit or impedance lower than that supported at output.

RED LED flashes 2x:
Supply voltage less than 9V.

RED LED flashes 3x:
Power supply voltage greater than 17V.

Installation

CAUTION: All connections to the power supply, input, and output connectors must be carried out only with the amplifier off.

Recommended wire gauge & fuse

• Positive / negative power supply cable _____ 2/0 AWG
• Output cables wire gauge ____ 7 AWG
• Remote cable _____ 18 AWG
• Protection fuse or circuit breaker ____ 210A

Calculated considering a maximum length of 4m. Distance greater than this, you will need to increase the cable gauges.

CAUTION Using wire gauges below the recommendation will result in power loss and  overheating of wiring.
Check polarity and never reverse power supply cables due to the risk of damage to the amplifier. It is compulsory to install a protection fuses or circuit breakers as close as possible from batteries.

Examples of connections in the power supply input.
Note: Required battery bank capacity: At least 210Ah
CAUTION: This equipment is not suitable for use in places where children may be present.

Technical features

Minimum Output Impedance:

• Rated power with 60Hz sinusoidal signal and THD <= 1%, with resistive loads, measured with Audio Precision APx525 audio analyzer or equivalent and the product at lower than 50°C case temperature and 14.4V supply voltage.
• Frequency response measured at 2 times the minimum impedance.
  The values as above are typical and may vary, due to electronic components tolerance or manufacturing process.
  For further informations or questions, visit our website or contact TARAMPS support.

Index

• Term of warranty
  • Technical assistance
• Introduction
  • Safety requirements
  • Safety
• Functions, inputs & outputs 10
  • Power supply connector
• LEDs indicators & protection system
• Installation
  • Recommended wire gauge & fuse
• Technical features

Term of warranty

TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.

This warranty excludes:

• Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
• Tamper or torn warranty seal;
• Cases in which the product is not used in adequate conditions;
• Defects caused by accessories, modifications or features attached to the product;
• The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
• Warranty card is not properly filled or torn;
• Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
• Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product

Technical assistance

For international support, check on our website: www.taramps.com.br/en/rede- de-assistencias-tecnicas or contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br

Declaration of Conformity

TARAMPS ELECTRONICS LTDA Alfredo Marcondes – SP Brazil Hereby, Taramps Electronics Ltda declares that the product BASS 5K complies with the Directive 2014/30/EU, according with the following harmonized standard:
EN 50498:2010 Electromagnetic compatibility (EMC) –  Product family standard for aftermarket electronic equipment in vehicles
The full text of the EU Declaration of Conformity is available at the following Product Page on Internet.

Fabricado por / Manufactured by: TARAMPS ELECTRONICS LTDA
CNPJ / TAX ID: 11.273.485/0001-03
R. João Silvério, 121 • Res. Manoel Martins Alfredo Marcondes – SP
Indústria Brasileira – Made in Brazil
www.taramps.com.br

References

• Taramps
• Taramps | WARRANTY & REPAIR CENTERS
• Taramps | Rede de Assistências Técnicas

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>