TARAMPS BASS 30K 1 Ohm Amplifier Instruction Manual

TARAMPS BASS 30K 1 Ohm Amplifier

Product Information

The product is a Taramps Electronics amplifier, specifically the BASS 30K model. It is designed for aftermarket electronic equipment in vehicles. The amplifier has a maximum power output of 30000W RMS* and 17010W RMS at 1 Ohm. It has various input and output options, including speaker inputs, RCA inputs, and a THRU OUT output. The amplifier also features adjustable settings such as level, subsonic, crossover, and bass boost. Safety requirements and precautions should be followed to ensure proper use of the amplifier.

Product Usage Instructions

1. Before using the amplifier, read the user manual and familiarize yourself with the product.
2. Ensure that the (-) negative input or recommended entry point is properly connected to avoid loss and damage.
3. Use the provided Taramps RCA cable to connect the amplifier to the RCA outputs of your CD/DVD player. This will help minimize noise interference.
4. Adjust the amplifier’s input sensitivity using the LEVEL setting. This will optimize the output signal levels from your CD/DVD player.
5. Set the SUBSONIC frequency using the variable adjustment dial. This will determine the starting frequency of the amplifier’s operation.
6. If desired, use the CROSSOVER and BASS BOOST settings to further adjust the sound output according to your preferences.
7. The THRU OUT output can be used to send the same input signal (INPUT) to another amplifier if needed.
8. Ensure proper safety measures are followed while using the amplifier. Refer to the safety symbols and heed the instructions to avoid any risk of injury or product damage.

Note:
The contents of the user manual are subject to change without prior notice, and Taramps Electronics Ltda reserves the right to modify the document contents at any time.

Term of warranty

TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of a defect during the warranty period, TARAMPS’ responsibility is limited to the repairing or substitution of the device of its own making.

This warranty excludes:

• Damaged products by improper installation, water infiltration, and violation by unauthorized individuals;
• Tamper or torn warranty seal;
• Cases in which the product is not used in adequate conditions;
• Defects caused by accessories, modifications, or features attached to the product;
• The product with damage from falling, bumps or nature-related problems (flooding, lightning, etc.);
• Warranty card is not properly filled or torn;
• Costs involving uninstallation, reinstallation of equipment as well and shipment to the factory;
• Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical assistance

For international support, check on our website:
www.taramps.com.br/en/rede-de-assistencias- tecnicas or contact direct the factory support:

• Phones: +55 18 3266-4050 / +55 18 99749-3391
• E-mail: service@taramps.com.br.

Introduction

• Read this manual before preparing the product. In case of doubt, contact our technical support: (18) 3266-4050 or www.taramps.com.br.
• At the end of its useful life, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling center for proper disposal.

**Declaration of Conformity

**

TARAMPS ELECTRONICS LTDA Alfredo Marcondes – SP Brazil

• Hereby, Taramps Electronics Ltda declares that the product BASS 30K complies with Directive 2014/30/EU, according to the following harmonized standard:
  EN 50498:2010 Electromagnetic compatibility (EMC) – Product family standard for aftermarket electronic equipment in vehicles

The full text of the EU Declaration of Conformity is available at the following Product Page on the Internet.

Safety requirements

To ensure proper use, please read through this manual before using the amplifier. It is especially important that you know the WARNINGS and CAUTIONS contained here.

• The installation of this amplifier must be done by a qualified professional.
• Wear safety glasses, insulated gloves, and correct tools for installing this product.
• This amplifier is for use with 12V batteries. Always check the voltage before installing.
• This amplifier must be installed in a firm place with at least 1” space around the heatsink for proper heat spreading.
• Never install the amplifier in places exposed to dust, humidity, and water. Pay attention to install it far from the fuel tank, fuel lines, heat sources, and other parts of the vehicle.
• Be sure to install a protection fuse or a circuit breaker near the battery. Follow the ampere rating as indicated here in this manual. Use of an improper fuse or circuit breaker could result in overheating, smoke, damage to the product, injury, or burns.
• Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through the car’s body.
• Before making any connection to the amplifier, disconnect the battery negative terminal.
• When in use, the external surface of may amplifier becomes hot. Avoid touching the heatsink area and keep children far from the amplifier.
• This amplifier may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.
• Output connections for speakers may have voltage levels when the amplifier is operating. Make sure that the amplifier is turned OFF before proceeding with any connection or disconnection in these terminals.
• If you want to dispose of this amplifier, don’t throw it on domestic waste. It must be collected by a used electronic product disposal service for proper recycling.

Safety
As you read this manual, pay attention to the safety symbols.

CAUTION
This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in a risk of injury to the user or product damage.

Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.

Functions, inputs & outputs

1. INPUT: Inputs of signals to be amplified. Connect these signals to RCA outputs of CD/DVD Player, using good quality shielded cables to avoid noise interference.

2. THRU-OUT: This output can send the same input signal (INPUT) to another amplifier.

3. LEVEL: It sets the amplifier input sensitivity, which allows an optimal adjustment to the output signal levels of nearly all models of CD/DVD Players found in the market.

4. SUBSONIC: Variable adjustment from 8Hz to 30Hz, which determines the beginning of the amplifier operating frequency.

5. LOW PASS: Variable adjustment from 60Hz to 250Hz, which determines the end of the amplifier operating frequency.

6. FREQ. Set the Bass Boost center frequency, from 35Hz up to 60Hz.

7. BASS BOOST: Boost the bass signals with a variable range of 0 to + 12dB.

8. REMOTE TERMINAL: The remote CD/DVD Player output must be connected by a 0.75 mm² (18 AWG) cable.

9. SPEAKER: Output (positive and negative) to the transducer’s connection (loudspeakers). Follow the polarity described and the minimum impedance recommended.
   To combine loudspeakers, the resulting impedance must be taken into consideration.
   CAUTION
   Due to the presence of voltage at the output terminals when the product is turned on, avoid contact with them. Risk of electric shock.

10. FANS: The BASS 30K, has four internal ventilation fans, and cannot be blocked. For perfect functioning, the amplifier must be installed in a cool and aired place. It is recommended not to embed it, so that the air circulates throughout the inside of the product extension, thereby preventing the thermal protection from acting.

CAUTION
The fan and ventilation openings are responsible for cooling the amplifier when it is in use, so it cannot be obstructed.

Power supply connector

1. NEGATIVE POWER SUPPLY TERMINAL: A 2 x 70mm² (2/0 AWG) cable as short as possible must be used, and connected to the negative battery pole.
2. POSITIVE POWER SUPPLY TERMINAL: Use a 2 x 70mm² (2/0 AWG) cable directly from the positive battery terminal with fuse (1160A), as close as possible to the battery.

It is recommended that all cables must have tinned ends to improve electrical contact and all power inputs must be used.

CAUTION
Before making any connections to the power terminals, make sure that the negative (-) of the vehicle battery is disconnected.

LEDS indicators & protection system

• ON (BLUE LED): Indicates that the amplifier is on.
• CLIP (YELLOW LED): Indicates that the amplifier is operating at the threshold of distortion or excessive temperature. If the red LED also blinks, it indicates excessive distortion.
• PROT (RED LED): It indicates whether there is a short circuit at the output of the amplifier or lower impedance that can be tolerated by the equipment; Check if the supply voltage is below 9V or above 17V.
• SHORT-CIRCUIT PROTECTION: Shut down the amplifier when detecting a short-circuit or impedance lower than the supported at the output.
• THERMAL PROTECTION: When the amplifier reaches a high-temperature condition (internally), the thermal shutdown will trip – The audio output will be disabled and the yellow LED will flash continuously. The internal fan will remain on until the internal temperature is back to normal operating levels, and then the amplifier will resume the audio playing. Don’t turn off the amplifier under these conditions, in order to get a shorter cooling time.
• HIGH/LOW SUPPLY VOLTAGE: If the supply voltage is below 9V LED (PROT) will flash 2x intermittently. Above 17V, the LED (PROT) will flash 3x intermittently, the protection system will be triggered, cutting off the audio signal. The amplifier will only return to Its normal functioning when it is switched off and on again and the supply voltage is between 9V and 17V.

Installation

CAUTION:
All connections to the power supply, input, and output connectors must be carried out only with the amplifier off.

Recommended wire gauge & fuse

• Positive/negative power supply cable _____2 x 2/0 AWG
• Output cables wire gauge____7 AWG
• Remote cable ____ 18 AWG
• Protection fuse or circuit breaker___1160A

Calculated considering a maximum length of 4m. Distance greater than this, you will need to increase the cable gauges.

CAUTION

• Using wire gauges below the recommendation will result in power loss and overheating of wiring.
• Check polarity and never reverse power supply cables due to the risk of damage to the amplifier.
• It is compulsory to install protection fuses or circuit breakers as close as possible to batteries.
• Examples of connections in the power supply input.
• Note: Required battery bank capacity: At least 1160Ah
• CAUTION This equipment is not suitable for use in places where children may be present.

Technical features

• Minimum Output Impedance: 10 hm
• Number of Channels: 01

Output Power @14.4VDC

• 1 OHM: 30000W RMS*
• 2 OHMS: 17010W RMS
• Input Sensitivity (Level 100%): 400mV
• Signal-to-noise Ratio: >90dB
• Frequency Response (Full Range): 8Hz ~ 250Hz (-3dB)

Crossover

• HPF (Subsonic Filter): 8Hz ~ 30Hz (-12dB/8ª) Variable
• LPF (Low Pass Filter): 60Hz ~ 250Hz (-12dB/8ª) Variable
• Bass Boost:
  • Freq.: 35Hz ~ 60Hz
  • Boost: 0 ~12dB
• Efficiency: 90%
• Input Impedance: 22K Ohms
• Protection System:
  • Short-Circuit to Output, Short on output to GND,
  • Low impedance at output, low/high supply voltage, and Thermal protection.
• Minimum Supply Voltage: 9VDC
• Maximum Supply Voltage: 17VDC
• Idle Consumption: 400mA
• Musical Consumption @14.4VDC: 1156A
• Rated Power Consumption: 2312A
• Dimensions (W x H x L): 239 x 73 x 1044mm (9.41″ x 2.87″ x 41.10″)
• Weigth: 19.20Kg (42.24lb)

Output power measured to 60Hz, nominal impedance, THD ≤ 10%, and battery voltage = 14.4VDC.

The values as above are typical and may vary, due to electronic components tolerance or manufacturing process. For further information or questions, visit our website or contact TARAMPS support.

• +55 18 3266-4050
• Fabricado por/Manufactured by:
• TARAMPS ELECTRONICS LTDA CNPJ/TAX ID: 11.273.485/0001-03
• R. João Silvério, 121 • Res. Manoel Martins Alfredo Marcondes – SP Indústria Brasileira – Made in Brazil
• www.taramps.com.br.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>