TARAMPS SMART 3 BASS Amplifier Free Shipping Worldwide Instruction Manual

TARAMPS SMART 3 BASS Amplifier Free Shipping Worldwide

Product Information

The product is a TARAMPS ELECTRONICS amplifier designed for electronic equipment in vehicles. It is a standard aftermarket product that is suitable for use with various types of speakers and audio systems. The amplifier has a power output of 3000W RMS and supports an impedance range of 1 Ohm to 2 Ohms. It features a highpass and low pass frequency crossover, bass boost, and a monitor with smart LEDs for visual feedback. The amplifier has multiple input and output connectors, including IN, OUT, and power input terminals. It operates at a voltage range of 9VDC to 16VDC and has a sensitivity of 0.22V to 4V. The amplifier also includes thermal protection, which allows it to automatically restart after cooling down.

Product Usage Instructions

1. Before connecting any cables, ensure that the amplifier is turned off.
2. For power supply, use positive and negative power supply cables with a minimum gauge of 4 AWG and a maximum gauge of 1/0 AWG.
3. Connect the output cables to the appropriate speakers or audio system using a wire gauge of 9 AWG.
4. Use an 18 AWG remote cable to connect the amplifier to a remote control device.
5. Install a protection fuse or circuit breaker with a rating of 150A as close as possible to the batteries.
6. Ensure correct polarity when connecting the power supply cables and never reverse them to avoid damage to the amplifier.
7. If using compression drivers, consult the manufacturer’s manual and install a passive filter on the positive terminal.

Note: The provided wire gauge recommendations are based on a maximum cable length of 4m. If the distance exceeds this, it is necessary to use thicker cables.

Index

• Term of warranty
• Technical assistance
• Smart line presentation

Introduction

• Smart line presentation
• Key recommendations
• Functions, inputs & outputs
• Power supply connector

Installation

• Technical features
• LEDs indicators & protection system
• Recommended wire gauge & fuse

Term of warranty

TARAMPS, located on Abilio Dagupan Street 274, Res. Manoel Martins – Alfredo Macondo’s, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is
limited to the repairing or substitution of the device of its own making

This warranty excludes

• Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
• Tamper or torn warranty seal;
• Cases in which the product is not used in adequate conditions;
• Defects caused by accessories, modifications or features attached to the product;
• The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
• Warranty card is not properly filled or torn;
• Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
• Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical assistance

For international support, check on our website:
www.taramps.com.br/en/rede-de-assistencias- tecnicas
or contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: angelo.assistencia@taramps.com.br

Smart Line Presentation

Multi-impedance: Featuring new control technology and new functions, the SMART 3 brings 3000W RMS rated power in the range of 1 to 2 Ohms: (1 – 1.33 – 1.5 – 1.67 and 2 Ohms with same power);

• SMART LEDS: LEDs output signal level indicator on top of product;
• RCA input for up to 4V RMS: Input gain adjustment that allows head units up to 4V RMS output level;
• Dual RCA IN / OUT Input: RCA connector with input and output function, eliminates the needing of “Y” cables for send the same unput signal to another amplifier;
• Power connector for cables up to 1/0 AWG: Allows the use of power cables with larger gauge (up to 50mm²) for higher performance;
• AUTO-Restart Protections : The amplifier automatically restarts after a protection event;
• RAMP audio initialization : After turning on the amplifier, audio is released gradually (ramp).

Introduction

Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced. As you read this manual, pay attention to the safety symbols.

Safety
This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage.

CAUTION
Read this manual before preparing the product. In case of doubt, contact our technical support: (18) 3266-4050 or www.taramps.com.br.

At the end of its useful life, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling center for proper disposal.

Declaration of Conformity
TARAMPS ELECTRONICS LTDA
Alfredo Macondo’s SPBrazil

Hereby, Taramps Electronics Ltd. declares that the products MART 3 complies with the Directive 2014/30/EU, according with the following harmonized standard:

EN 50498:2010 Electromagnetic compatibility (EMC)  Product family standard for aftermarket electronic equipment in vehicles The full text of the EU Declaration of Conformity is available at the following Product Page on Internet.

Safety requirements

To ensure proper use, please read through this manual before using the amplifier. It is specially important that you know the WARNINGS and CAUTIONS contained here.

• The installation of this amplifier must be done by a qualified professional.
• Wear safety glasses, insulated gloves and correct tools for installing this product.
• Output connections for speakers may have voltage levels when the amplifier is operating.
• Make sure that the amplifier is turned OFF before proceed any connection or disconnection in this terminals.
• When in use, the external surface of may amplifier becomes hot. Avoid touching the heatsink area and keep childrens far from the amplifier.
• This amplifier must be installed in a firm place with at least 1” space around the heatsink for proper heat spreading.
• This amplifier is for use with 12V batteries. Always check the voltage before installing.
• Never install the amplifier in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.
• Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating as indicated here in this manual. Use of improper fuse or circuit breaker could result in overheat, smoke, damage to product, injury or burns.
• Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through car’s body.
• Before make any connection to amplifier, disconnect the battery negative terminal.
• When in use, the external surface of may amplifier becomes hot. Avoid touching the heatsink area and keep children’s far from the amplifier.
• This amplifier may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.
• Output connections for speakers may have voltage levels when the amplifier is operating.
• Make sure that the amplifier is turned OFF before proceed any connection or disconnection in this terminals.
• If you want to dispose this amplifier, don’t throw it on domestic waste. It must be collected by an used electronic product disposal service for proper recycling.

Safety

As you read this manual, pay attention to the safety symbols.

This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage.

Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.

Functions, inputs & outputs

1. IN
   Input of signal to be amplified. Connect the to the RCA output of the Head Unit using good shielded cable to avoid noise interference.

2. OUT
   Audio signal output. Sends the same input (IN) signal to another amplifier, allowing cascading.

3. GAIN
   Adjusts the input sensitivity of the amplifier, allowing a perfect adjustment to the output signal levels of various head units models on the market. It is possible to adjust from 4V (minimum sensitivity) to
   0.2V (maximum sensitivity).

4. CROSSOVER
   HIGH PASS FILTER (HPF): Variable setting from 10Hz to 90Hz, which determines the start of the amplifier’s operating frequency.

5. BASS BOOST
   FREQ.: Set the frequency of bass boost from 35Hz to 55Hz.
   BOOST: Set the boost level from 0 to + 10dB at the frequency set in FREQ.

6. MONITOR
   Accessory connection that has the function of monitoring the amplifier, displaying clipping and protection status. (Included accessory).

7. SPEAKER: SPEAKER
   Output (positive and negative) for connecting transducers (speakers). Follow the indicated polarity.

8. CROSSOVER
   IN: Input of signal to be amplified. Connect the to the RCA output of the Head Unit using good shielded cable to avoid noise interference.
   For speaker associations, the impedance to consider is the resulting impedance

• Loudspeakers
  

• Quantity
  

• Impedance
  

• Resulting
  

• Impedance
  

• Power

| 4 x 4 OHMS| 1 OHM| 3000W RMS
---|---|---|---

| 3 x 4 OHMS| 1.33 OHMS

| 4 x 6 OHMS| 1.5 OHMS

| 2 x 4 OHMS| 2 OHMS

Power supply connector

1. SMART COOLER: This amplifier has two internal ventilation fans. For perfect functioning, the amplifier mustbe installed in a cool and aired place with at least 1” (25mm) space around the heatsink for proper heat spreading.
   The usually working temperature of amplifier is 65°C.
   The fan and ventilation openings are responsible for cooling the amplifier when it is in use, so it cannot be obstructed.

2. POSITIVE POWER SUPPLY: Use a minimum 4 AWG up to maximum of 1/0 AWG cable direct from the positive battery terminal, with fuse or circuit breaker (150A), as close to it as possible.

3. TERMINAL REMOTE: It must be connected to the remote output of the head unit using a 18 AWG cable.

4. NEGATIVE POWER SUPPLY: Use a cable of minimum 4 AWG up to maximum of 1/0 AWG as short as possible, connected to the negative battery pole.

We recommend that all cables have tinned ends for better electrical contact.

In case of power bus bar using, avoid tightening with extenders on the allen wrench, as excessive torque may break the the terminal.

CAUTION Before making any connections to the power terminals, make sure that the negative of the vehicle battery is disconnected.

LEDS indicators & protection system

On – Displays audio level.

|

____   Blue LED on

| Working amplifier
2x LEDs flashing 2x

|

Red LED

____    flashes 2x

| Battery with voltage below 9V
3x LEDs flashing 3x

|

Red LED

____    flashes 3x

| Battery with voltage above 16V
LEDs flashing 6x per second Continuously

| Red LED

____    flashing 6x per

second continuously

| Short circuit on output or between output terminal to GND
LEDs flashing 1 second on 1 second off

| Yellow LED flashing 1 sec. on 1 sec. off

| Temperature above operating limit (> 85 ° C)

The thermal protection waits for cooling before restarting.
If it goes into protection, the amplifier will automatically restart.

Example

Low Battery Protection: Working amplifier Red LED (LED Monitor) or Smart LEDS, flashes 2x Red LED (LED monitor) or Smart LEDS, flashes 2x Amplifier restarts.
Installation

CAUTION
All connections to power supply, input and output connectors must be carried out only with amplifier off.

Positive / negative power supply cable ____Min. 4 AWG / Max.1/0 AWG
Output cables wire gauge____9 AWG
Remote cable ____ 18 AWG
Protection fuse or circuit breaker____150A

Calculated considering a maximum length of 4m. Distance greater than this, you will need to increase the cable gauges.

Using wire gauges below the recommendation will result in power loss and overheating of wiring.

Check polarity and never reverse power supply cables due to the risk of damage to the amplifier.
It is compulsory to install a protection fuses or circuit breakers as close as possible from batteries.

Note : In case of compression driver you must install a passive filter in the positive terminal of the same ones (Consult transducer’s manufacturer manual

Examples of connections in the power supply input.
Note : Required battery bank capacity: At least 150Ah

The entire aluminum surface of the amplifier serves as a heat sink. The usually working temperature is 65°C. So, avoid contact with this surface when the amplifier is in use.

This equipment is not suitable for use in places where children may be present.

Technical features

• Output Impedance Range 1 Ohm ~ 2 Ohms
• Number of Channels  01

• Input Sensitivity 0.22V ~ 4V
• Signal- to-noise Ratio >90dB
• Frequency Response 10Hz ~ 10KHz (-3dB)
• Crossover  HPF (High Pass Filter) 10Hz ~ 90Hz (-12dB/8ª) Variable
• LPF (Low Pass Filter) 90Hz ~ 10KHz (-12dB/8ª) Variable
• Bass Boost Freq 35Hz ~ 55Hz Boost 0 ~ +10dB
• Efficiency 79%
• Input Impedance 10K Ohms
• Protection System Output short-circuit, low/high supply voltage and Thermal protection
• Minimum Supply Voltage 9VDC
• Maximum Supply Voltage 16VDC
• Idle Consumption 2.40A
• Musical Consumption / @12.6VDC 150A
• Rated Power Consumption 300A
• Dimensions (W x H x L) 8.98″ x 2.76″ x 9.37″
• Weigth 5.72lb

*Rated power with 40Hz and 1KHz sinusoidal signal, THD <= 1%, with resistive loads, measured with SMD/AD-1 audio power analyzer or equivalent and the product at lower than 50°C case temperature and 12,6V supply voltage.

The values as above are typical and may vary, due to electronic components tolerance or manufacturing process.
For further information’s or questions, visit our website or contact TARAMPS ELECTRONICS support.

• MN_017624_R01
• Fabricado por / Manufactured by:
• TARAMPS ELECTRONICS LTDA
• CNPJ / TAX ID: 11.273.485/0001-03
• Res. Manoel Martins
• Alfredo Marcondes SP
•  Made in Brazil

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>