ToolShed TSDH1 Diesel Heater User Manual

ToolShed TSDH1 Diesel Heater

Product Information

• The Toolshed Diesel Heater is a commercial and light industrial space heating appliance.
• It is a portable stand-alone heater designed for use in large, well-ventilated spaces.
• The heater should not be connected to any flue or duct that may restrict airflow.
• Product Model Numbers: TSDH1 (20kW), TSDH3 (30kW), TSDH5 (50kW)
• For more information about warranty coverage, please refer to the Terms & Conditions on our website.

Specifications

Model| Heat Input (kW)| Air Flow Rating (m3/h)| Fuel Type| Fuel Consumption (LPH)| Voltage (V/Hz)| Air Pressure Setting| Current Rating (A)| Electrical Power (W)| Fuse Rating| Net Weight (kg)| Length (mm)| Width (mm)| Height (mm)| Tank Capacity (L)| Operating Range (h)| Fuel Gauge| Handle| Ambient Thermostat| Malfunction Detection Light
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
TSDH1| 20| 550| Diesel| 1.94| AC220-240V/50| 0.32 bar| 1.1| 230| T3.15A| 14| 750| 315| 415| 19| ~10| YES| 1| Built-In| Built-In
TSDH3| 30| 720| Diesel| 2.82| AC220-240V/50| 0.31 bar| 1.1| 230| T3.15A| 21| 880| 456| 590| 38| ~13| YES| 1| Built-In| Built-In
TSDH5| 50| 1100| Diesel| 4.71| AC220-240V/50| 0.45 bar| 1.5| 340| T3.15A| 27| 1090| 490| 585| 56| ~12| YES| 1| Built-In| Built-In

Product Usage Instructions

• This diesel heater is intended for commercial and light industrial space heating.
• Ensure the heater is used only in a large, well-ventilated space.
• Do not connect the heater to any flue or duct that may restrict airflow.
• Adequate air circulation is important to prevent carbon monoxide (CO) poisoning. Do not use the heater indoors without proper ventilation.
• Avoid storing or using gasoline or other flammable vapors and liquids near the heater.
• Keep solid combustibles such as building materials, paper, or cardboard at a safe distance from the heater.
• Do not use the heater in spaces that may contain volatile or airborne combustibles, gasoline, solvents, paint thinner, dust particles, or unknown chemicals.
• This heater is not intended for home or recreational vehicle use.
• The electrical system to which the appliance is connected must comply with current legislation and require an RCD (Residual Current Device) for installation.
• Before performing any maintenance operations, unplug the appliance and allow it to cool down.
• Always check the power cable for any damage before using the appliance.

NOTE:
This manual is only for your reference. Due to the continuous improvement of the ToolShed products, changes may be made at any time without obligation or notice.

WARRANTY
This product may be covered under the ToolShed warranty. For more information see our Terms & Conditions at www.thetoolshed.co.nz
This heater is intended to be used for commercial and light industrial space heating. It is a portable stand-alone appliance to be used inside a large well-ventilated space.
It is important that it is not connected to any flue or duct that might restrict the airflow within the heater.

SPECIFICATIONS

Fuel Consumption

(LPH)

| 1.94| 2.82| 4.71
Voltage (V/Hz)| AC220-240V/50| AC220-240V/50| AC220-240V/50
Air Pressure Setting| 0.32 bar| 0.31 bar| 0.45 bar
Current Rating (A)| 1.1| 1.1| 1.5
Electrical Power (W)| 230| 230| 340
Fuse Rating| T3.15A| T3.15A| T3.15A
Net Weight (kg)| 14| 21| 27
Length (mm)| 750| 880| 1090
Width (mm)| 315| 456| 490
Height (mm)| 415| 590| 585
Tank Capacity (L)| 19| 38| 56
Operating Range (h)| ~10| ~13| ~12
Fuel Gauge| YES| YES| YES
Handle| 1| 1| 1
Ambient Thermostat| Built-In| Built-In| Built-In
Malfunction Detection

Light

| Built-In| Built-In| Built-In

SERVICE

• Have your tools and machinery serviced at The ToolShed with ToolShed replacement parts. This will ensure that the safety of the power tool or machine is maintained.

IMPORTANT INFORMATION

GENERAL SAFETY GUIDELINES

• WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure to follow instructions and warnings could lead to serious injury, electric shock, or fire. Save ALL warnings and instructions for future reference.

WORK AREA SAFETY

• Ensure that your work area is kept well-lit and clean. Lack of visibility and clutter greatly increase the risk of accidents.
• Keep bystanders and children clear when operating a power tool or machine. They can cause distraction or risk injury themselves.
• Ensure you are not operating the power tool or machinery in the presence of flammable gases, dust, liquids, or anything that creates an explosive atmosphere. Power tools and machinery can create sparks which can lead to ignition in these environments.

PERSONAL SAFETY

• Always wear personal protective equipment. Eye protection, ear protection, dust masks, and other protective equipment will help to reduce the risk of personal injury.
• Dress appropriately. Do NOT wear jewellery or lose clothing that can get caught in moving parts. Keep hair, loose clothing, jewelry, and anything else that could be of risk away from moving parts or they could be caught.
• Always remain alert and do NOT operate the power tool or machinery under the influence of any substances (drugs, medication, alcohol). Losing focus could lead to injury while operating power tools and machinery.
• Always keep proper footing and balance. Overreaching can lead to slipping and falling which can result in injury.
• Ensure the power switch is in the off position before connecting any battery or power source to the power tool or machinery. This can lead to accidents as tools and machinery can fire suddenly when it is not expected and lead to accidents.
• Ensure loose parts such as a wrench or adjusting key are removed before starting the power tool or machinery. Failure to remove these can result in serious injury.

ELECTRICAL SAFETY

• Do NOT use the power tool or machinery in rainy conditions or wet areas where the power tool or machinery could get wet. Water in the power tool or machinery can lead to electric shock.
• Only use the power tool or machinery when the plug correctly matches the power outlet. Modifying plugs greatly increases the risk of electric shock.
• Keep the power cord away from anything that could damage it such as sharp edges, moving parts or heat. A damaged power cord increases the risk of electric shock.
• Only operate outdoors with the use of an outdoor extension lead. Not all extension leads are suited to outdoor use and using one which is not can greatly increase the risk of electric shock.

ADDITIONAL SAFETY FOR DIESEL HEATER.

• WARNING: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
• WARNING: Risk of fire, burn, inhalation, and explosion hazard. Keep solid combustibles such as building materials, paper, or cardboard a safe distance away from the heater.
• Never use the heater in spaces that do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint thinner, dust particles, or unknown chemicals.
• WARNING: Direct-fired heaters may cause carbon monoxide (CO) poisoning when incorrectly used,e. g indoors without adequate air circulation, or if not properly working. CO poisoning may lead to death.
• Not for home or recreational vehicle use.
• The electrical system to which the appliance is connected must comply with current legislation. Installation requires an RCD (Residual Current Device).
• Unplug the appliance and allow it to cool down before performing any maintenance operations.
• Always check the power cable before using the appliance. It must not be bent, taut, stretched, crushed, or in any way damaged.
• The power cable must be replaced by qualified personnel only. Use an original power cable with a 3-pin approved plug only.
• The front outlet is very hot during operation. DO NOT TOUCH.

ASSEMBLY

• Remove the heater from its carton. If it is damaged in any way, do not use it and contact your dealer.
• TSDH1 – This heater only requires attaching the plastic handle, no other assembly is required.
• TSDH3/TSDH5 – The following accessories are supplied in the shipping carton:

To assemble the heater, proceed as follows (see Fig. 1):

1. Insert the wheel shaft J to the corresponding hole of feet pipe E. Insert the cotter K to the corresponding holes; out plain washers I to the two sides of the shaft. Slide the wheel H over the wheel shaft J. Screw the nut G to fix the wheel on to the shaft.
2. Put the heater body on the feet pipe assembly. Make sure the 4 holes of handle A point towards the corresponding 4 holes on the feet pipe.
3. Using the screw B, spring washer C, plain washer D, and nut F – fix the feet pipe assembly and handle to the tank.

INSTALLATION INSTRUCTIONS

• WARNING: Position the heater on a flat, level, non-flammable, solid surface.
• WARNING: Direct-fired heaters are intended for use in outdoor open areas or in indoor well-ventilated areas. For indoor use, provide permanent ventilation openings of at least 25cm2/kW, equally distributed between floor and ceiling height with a minimum of 250cm2.

• Only install the heater in a normal upright position.
• Do not place the heater near walls, corners, or low ceilings.
• Do not place the heater below a socket outlet.
• Do not place the heater on moving vehicles where it can tip over.
• Keep the heater away from flammable, combustible, explosive, or corrosive materials.
• Keep the heater away from curtains or similar materials that could block the air inlet and outlet.
• Never block or restrict the air inlet and outlet for any reason.
• Keep the power cable away from heat sources, sharp edges, and cutting and moving parts.
• Do not expose directly to the weather or to excessive humidity.
• Do not place the heater in the immediate surroundings of a bath, shower, or swimming pool.
• Follow general and specific fire safety regulations in force in all fields of applications.

In any case, ensure the following minimum safety clearances from materials or objects in the surroundings of the heater:

• Side 2m
• Air Inlet Side 2m
• Top 2m
• Hot Air Outlet Side 3m
• Floor 0m
• Do not connect direct-fired heaters to air ducts.

OPERATION

STARTUP

1. Fill the tank with clean fuel. Only use diesel. The fuel gauge on top of the tank allows you to check the fuel level.
2. Connect the power cord plug to an earthed electrical supply.

MODELS TSDH1 / TSDH3:

1. Once the startup steps are completed the power indicator will light up and the display window will show the ambient temperature value.
2. Push the power switch to the ON position.

If the thermostat control knob setting temperature is higher than the ambient temperature, the electrodes start sparking and after 7 seconds the heater starts.

MODEL TSDH5

1. Once the startup steps are completed, the left display window will show “—“ and the right window will show the ambient temperature value.
2. Push the power switch to the ON position.
3. The default temperature setting is 20° which will be shown on the left display window.
4. If the ambient temperature is lower than the default temperature, turn the thermostat control knob to the desired temperature. The electrodes will start sparking and after 7 seconds the heater will start.

MANUAL RESET / RESTART

• If the heater is in lock-out mode, check and remove the cause of the lock-out before restarting the heater.
• To reset, turn the ON/OFF switch to 0 and then again to I.
• In case of repeated malfunction, call technical service.
• Turning the thermostat control knob will NOT reset the heater.

SHUT DOWN

• Move switch to the OFF (O) position. Unplug the unit.
• NEVER disconnect the heater from the mains to stop it while in operation. Always allow the cooling sequence to be completed (TSDH5), otherwise, the residual heat could damage internal components.
• Do not cover the heater. Do not block the air inlet and outlet.
• The heater outlet is very hot during operation and after use. DO NOT touch. Use personal protection equipment if required.
• Unplug the heater before moving it. Never pull the cable to unplug or move the unit.
• Do not leave the heater unattended when in use.
• Never use the appliance with wet hands or when either the heater or the power cable is wet.
• If the supply cable is damaged, contact your local ToolShed.

CLEANING, MAINTENANCE & STORAGE

• Regularly wipe the enclosure using a soft sponge or cloth. For very dirty parts, use a sponge wetted with lukewarm water and a mild detergent. Then dry using a clean cloth.
• Keep air inlet and fan free from dust and dirt. To clean the inner parts, gently blow compressed air through the air inlet.
• Regularly inspect the power cable: if worn, cracked, or damaged, have it replaced by a service technician.
• Before storing the heater, make sure it is completely cool and dry. Cover the unit with a plastic bag, put it in its packing box, and store it in a dry ventilated place.
• Before starting any maintenance task, shut down, unplug, and let the heater cool down for at least 15 minutes.
• Do not attempt any electrical repair yourself. If the heater needs repair, contact a qualified technician.
• Do not use a faulty unit unless a qualified technician has inspected and repaired it.
• When cleaning, make sure that water does not enter the unit.
• Do not open the enclosure to clean the inner parts. Do not spray water into the heater.
• Never use solvents, gasoline, toluene, and similar aggressive chemicals to clean the heater.
• The following checks by a QUALIFIED TECHNICIAN are recommended before every seasonal use:

Nozzle

• Carefully unscrew the nozzle from the nozzle fitting. Blow compressed air through the nozzle orifice to free it from dirt. Replace the nozzle if necessary.

Air Filters

• Clean air filters. Remove the filter end cover (11), wash the air intake filter (10) using a light detergent, and dry it thoroughly before re-installing. Replace the air delivery filter (9) once a year.

Ignition Electrodes

• Clean, adjust, and if necessary, replace the ignition electrode.

Compressor Pressure Adjustment

• The compressor pressure is factory-set and must be checked and adjusted by qualified technicians only. Tampering with the unit may be dangerous.
• Remove the pressure gauge cap. Connect a pressure gauge on the pressure measuring port on the rear guard. Start the heater and read the air pressure value.
• If necessary, adjust the pressure to the correct value.
• Turn the adjusting screw clockwise to increase pressure and anti-clockwise to decrease it.

TROUBLESHOOTING

ELECTRICAL DIAGRAMS

TSDH1 / TSDH3

TSDH5

www.thetoolshed.co.nz

Documents / Resources

| ToolShed TSDH1 Diesel Heater [pdf] User Manual
TSDH1 Diesel Heater, TSDH1, Diesel Heater, Heater
---|---

References

• The ToolShed - NZ | Power Tools | Hand Tools | Air Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>