BOSCH GTS15-10 Jobsite Table Saw with Gravity Rise Wheeled Stand Instructions

BOSCH GTS15-10 Jobsite Table Saw with Gravity Rise Wheeled Stand

Safety Symbols

Safety Instructions

WARNING: Read all instructions. Failure to follow all instructions listed below may result in serious personal injury. Fully assemble and tighten all the fasteners required for this stand. Periodically check that all fasteners are attached and adjusted according to the assembly instructions included in this manual. A loose stand is unstable and may shift in use and cause serious injury. Turn tool switch off and disconnect power before mounting to the stand. Unintended startup during assembly can cause injury. Before operating make sure the entire unit is placed on a solid, flat, level surface. Serious injury could occur if tool is unstable and tips. Never stand on tool or its stand or use as ladder or scaffolding. Serious injury could occur if the tool is tipped or the cutting tool is accidentally contacted. Do not store materials on or near the tool such that it is necessary to stand on the tool or its stand to reach them. Use only Bosch replacement parts. Any others may create a hazard.

Pre-Assembly

You have purchased a Bosch Table Saw Stand GTA50W, designed for job site use. This unit sets up and folds quickly, and is easily loaded or unloaded by one person into a truck.

Before You Assemble This Table Saw Stand

(Fig. 1, Fig. 2)
Sort out and account for all parts to make sure that you have all the necessary materials to assemble your stand. Do not discard packing material until all parts are accounted for.

Table Saw Stand Parts

Item| Qty.| Part Description
A| 1| Handle Bar
B| 2| Wheel
C| 1| Saw Mounting Bar
D| 1| Mid Pivot Bar
E| 1| Wheel Bar
F| 1| Left Linkage Bar
G| 1| Right Linkage Bar
H| 1| Support Bar Right
I| 1| Support Bar Left
J| 1| Lower Cross Bar

Tools Required

• 13 mm and 17 mm openings on blade wrench (included on table saw)
• 5 mm hex wrench (included on table saw)

Stand Assembly Hardware (packaged in six bags connected together)

Part Description| Specs.| Qty.
Bag A
Flat Washer| ⌀30 x ⌀13 x 3 mm| 4
Lock Nut| M12| 2
Bag B
Hex Head Bolt| M10 x 15 mm| 2
Bag C
Hex Head Bolt| M8 x 45 mm| 6
Lock Nut| M8| 6
Rubber Thread Cap| n/a| 2
Bag D
Foot Pad| n/a| 2
Hex Head Bolt| M8 x 60 mm| 2
Flat Washer| ⌀16 x ⌀18.2 x 1.5 mm| 2
Lock Nut| M8| 2
Bag E
Hex Head Bolt| M8 x 80 mm| 8
Flat Washer| ⌀16 x ⌀18.2 x 2.5 mm| 16
Lock Nut| M8| 8
Rubber Thread Cap| n/a| 2
Bag F
Hex Head Bolt| M8 x 110 mm| 2
Flat Washer| ⌀16 x ⌀18.2 x 2.5 mm| 4
Lock Nut| M8| 2

Assembly

Step 1. Attach Wheels

(Fig. 3) All the hardware needed for this procedure is in Bag A.

1. Mount one (1) Flat Washer and the Wheel B on the axle of the Wheel Bar E.
2. Place one (1) Flat Washer on the threaded end of the wheel axle. Thread the Lock Nut on the threaded end of the wheel axle by hand.
3. Using the 17 mm opening on the blade wrench provided with the table saw, tighten the Lock Nut until the Washer does not move freely. Spin the Wheel B to check tightness. If the Wheel B doesn’t turn freely, loosen the Nut by 1/8 to 1/4 of a turn.
4. Repeat the same steps with the other Wheel B.

Step 2. Attach Linkage Bars to Wheel Bar
(Fig. 4) All the hardware needed for this procedure is in Bag B.

1. Mount the Left Linkage Bar F on the welded bushing of the Wheel Bar E.
2. Using the 5 mm hex wrench included on the table saw, securely tighten the Hex Head Bolt into the welded bushing.
3. Repeat the steps above for the Right Linkage Bar G assembly.
   • Note: The Right Linkage Bar G features a welded pin while the Left Linkage Bar F does not.

Step 3. Attach Linkage Bars to Support Bars

(Fig. 5) All the hardware needed for this procedure is in Bag C.

1. Insert the end of the Left Linkage Bar F into the Left Support Bar H and align the holes of both bars.
2. Insert two (2) Hex Head Bolts through the holes of the Left Linkage Bar F and Left Support Bar H. Install two (2) M8 Lock Nuts, and use the 5 mm hex wrench and the 13 mm wrench opening on the blade wrench (included on table saw) to securely tighten the hardware.
3. Repeat the steps above for the Right Linkage Bar G and the Right Support Bar I.

Step 4. Attach Lower Cross Bar to Support Bars
(Fig. 6) All the hardware needed for this procedure is in Bag D.

1. Insert the ends of the Support Bars H and I into the Lower Cross Bar J, and align the holes of both bars.
2. Place one (1) Flat Washer and one (1) Foot Pad on one (1) Hex Head Bolt. Insert the Bolt through the holes in the Left Support Bar H and the Lower Cross Bar J. Install one (1) M8 Lock Nut, and use the 5 mm hex key and a 13 mm wrench to securely tighten the hardware.
3. Repeat the step above for the Right Support Bar I and the Lower Cross Bar J.

Step 5. Attach Handle Bar to Lower Cross Bar Assembly

(Fig. 7) All the hardware needed for this procedure is in Bag C.

1. Insert the ends of Handle Bar A into the Linkage Bars F and G and align the holes of both bars.
2. Insert two (2) Hex Head Bolts through the holes of the Handle Bar A and Linkage Bars F and G. Install one (1) Lock Nut, and use the 5 mm hex wrench and a 13 mm wrench to securely tighten the hardware until the parts cannot move freely.
3. To cover the Bolt threads in the Handle area, place the Rubber Thread Caps on the ends of the Hex Head Bolts.

Step 6. Attach Mid Pivot Bar to Wheel Bar Assembly
(Fig. 8) All the hardware needed for this procedure is in Bag E.

1. Insert a Hex Head Bolt through the hole on the left side of the Wheel Bar E, then through one (1) flat washer, and then through the Mid Pivot Bar D.
2. Place one (1) Flat Washer on the Hex Head Bolt. Install one (1) Lock Nut, and use the 5 mm hex key and a 13 mm wrench to securely tighten the hardware until the parts cannot move freely. Then loosen the Nut by 1/8 to 1/4 turn.
   • Note: To ensure that the joint is not overtightened, ensure that the middle Flat Washer is able to spin freely.
3. Repeat the steps above for the right side of the assembly.

Step 7. Attach Saw Mounting Bar to Mid Pivot Bar Assembly
(Fig. 9) All the hardware needed for this procedure is in Bag F.

1. Insert a Hex Head Bolt through the hole on the left side of the Saw Mounting Bar C, then through one (1) Flat Washer, and then through the Mid Pivot Bar D.
2. Place one (1) Flat Washer on the Hex Head Bolt. Install one (1) Lock Nut, and use the 5 mm hex key and a 13 mm wrench to securely tighten the hardware until the parts cannot move freely. Then loosen the Lock Nut by 1/8 to 1/4 turn.
   • Note: To ensure that the joint is not overtightened, ensure that the middle Flat Washer is able to spin freely.
3. Repeat the steps above for the right side of the assembly.

Step 8. Attach Saw Mounting Bar to Linkage Bar Assembly
(Fig. 10) All the hardware needed for this procedure is in Bag E.

1. Insert a Hex Head Bolt through the Left Linkage Bar F, then through one (1) Flat Washer, and then through the Saw Mounting Bar C.
2. Place one (1) Flat Washer on the Hex Head Bolt. Install one (1) Lock Nut, and use the 5 mm hex key and a 13 mm wrench to securely tighten the hardware until the parts cannot move freely. Then loosen the Lock Nut by 1/8 to 1/4 turn.
   • Note: To ensure that the joint is not overtightened, ensure that the middle washer is able to spin freely.
3. To cover the Bolt threads in the Handle area, place the Rubber Thread Caps on the ends of the Hex Head Bolts.
4. Repeat the steps above for the right side of the assembly.

Mounting Table Saw to Stand

Mounting Bosch GTS15-10 Table Saw to GTA50W Stand
(Fig. 11) All the hardware needed for this procedure is in Bag E.

1. Align the saw as shown in Fig. 11.
2. Insert one (1) Hex Head Bolt through one (1) Flat Washer, the mounting hole in the table saw, and through the Saw Mounting Bar C of the stand.
3. Place one (1) Flat Washer. Install one (1) Lock Nut, and use the 5 mm hex key and a 13 mm wrench to securely tighten the hardware.
4. Repeat the steps above for the three remaining mounting holes.

Operating Instructions

Fold Stand Upright (Fig. 12, Fig. 13)
WARNING: Keep fingers clear of hinge points when folding or unfolding the stand.

1. Press the Foot Pedal 1 to release the Hook 2 from the Locking Pin 3.
2. With both hands on the Handle 4, pull up and push forward on the stand until it locks in the upright position.

Lower Stand (Fig. 12, Fig. 13)

1. Press the Foot Pedal 1, then pull back on the stand slightly to disengage.
2. With both hands on the Handle 4, pull back and lower the stand until it locks in position.

Lowering Stand to its Lowest Position (Fig. 14)

• Begin with the stand in the locked upright position.
• Firmly grip the Handle 4 with both hands and place one foot against the Kick Bar 5. Pull back on the Handle 4 and lower the stand to the ground.

Maintenance

Check Fasteners
Periodically check that all fasteners are attached and adjusted according to the assembly instructions included in this manual.

Tool Lubrication
Your Bosch tool has been properly lubricated and is ready for use.

Service

WARNING: NO USER-SERVICEABLE PARTS. We recommend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station.

LIMITED WARRANTY

For details on the terms of the limited warranty for this product, go to https://rb-pt.io/PowerToolWarranty. or call 1-877-BOSCH99.

CONTACT

• Call Toll-Free for Consumer Information and Service Locations
• 1-877-BOSCH99 (1-877-267-2499) www.boschtools.com.
• 1609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 1
• 4/26/2023 11:32:11 AM
• © Robert Bosch Tool Corporation 1800 W. Central Road Mt. Prospect, IL 60056-2230
• Exportado por: Robert Bosch Tool Corporation Mt. Prospect, IL 60056-2230, E.U.A.
• Importado en México por: Robert Bosch, S.A. de C.V., Calle Robert Bosch No. 405, Zona Industrial, Toluca, Edo. de
• México, C.P. 50070,
• Tel. (722) 2792300
• 1609B08221 04/2023

References

• Bosch Power Tools | Boschtools
• Product Warranty | Boschtools

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>