ADLER EUROPE AD 4130 Slow Juicer User Manual
- June 13, 2024
- ADLER EUROPE
Table of Contents
ADLER EUROPE AD 4130 Slow Juicer
Product Information Product Name: Slow Juicer AD 4130 / AD4131
Main Product Unit:
- 1. Power cord with plug
- 2. Engine unit
- 3. Swing Switch
- 4. Locking ring
Extraction Function:
- 5. Juice cup
- 6. Foam filter plate
- 7. Pulp cup
- 8. Extraction pusher
- 9. Juice tray
- 10. Squeezing tube
- 11. Extraction screw
- 12. Filter net
- 13. Extraction cover
Meat Grinder Function (Only in AD4131):
- 14. Pusher for meat grinder
- 15. Food tray
- 16. Feeding tube
- 17. Feeding screw
- 18. Cross knife
- 19. Cutting disc 3mm
- 20. Cutting disc 5mm
- 21. Cutting disc 8mm
- 22. Fixing ring
- 23. Sausage attachment
Salad Maker (Only in AD4131):
- 24. Salad maker pusher
- 25. Salad maker tube
- 26. Salad maker tube cover
- 27. Slicer
- 28. Shredder
- 29. Masher
Technical Data:
- Maximum working duration: 10 minutes
- Rest time: 30 minutes
- Power: 150 W
- Voltage: 220-240V ~ 50Hz
Product Usage Instructions
Before first use:
- Remove all packaging material.
- Clean the device and all attachments with warm water mixed with dishwashing soap.
- Dry with a dry and soft towel or paper towel.
Button Description:
The device has 1 rocking switch to operate. The 3 functions of the switch are as follows:
- I: This turns on the device. After pressing it will continue working until turned off.
- O: Off position. The device will be turned off when the switch is in this position.
- R: Reverse. When pressed, the engine will turn into reverse. The Auger/slicer will turn in the opposite direction compared to normal operation. When released, the device will switch to the Off position.
Juice Extractor Models AD4130 and AD4131:
Turn the locking ring counterclockwise, and then remove the salad maker tube from the machine.
To protect your environment:
- Please separate carton boxes and plastic bags and dispose of them in corresponding waste bins.
- Used appliances should be delivered to dedicated collecting points due to hazardous components, which may affect the environment.
- Electrical appliances must be returned to reduce their reuse and utilization.
- If the device contains batteries, they should be delivered to dedicated points separately.
GENERAL SAFETY TERMS IMPORTANT SAFETY INSTRUCTIONS READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
-
Before using the device, read the user manual and follow the instructions contained therein. The manufacturer is not liable for damage caused by using the device contrary to its intended use or improper operation.
-
The device is for home use only. Do not use it for other purposes that are inconsistent with its intended use.
-
The device should only be connected to a 220-240V, ~50/60Hz socket. In order to increase the safety of use, many electrical devices should not be connected to one power circuit at the same time.
-
Be especially careful when using the device when children are around. Do not allow children to play with the device and do not allow children or people unfamiliar with the device to use it
-
WARNING: This equipment can be used by children over 8 years of age and persons with reduced physical, sensory or mental abilities, or persons without experience or knowledge of the equipment, if it is carried out under the supervision of a person responsible for their safety or they have been given instructions on the safe use of the device and are aware of the dangers associated with its use. Children should not play with the equipment. Cleaning and user maintenance should not be performed by children, unless they are over 8 years of age and are supervised.
-
Always remove the plug from the socket after use by holding the socket with your hand.
DO NOT pull on the net cord. -
Do not immerse the cord, plug or the entire appliance in water or any other liquid. Do not expose the device to weather conditions (rain, sun, etc.) or use it in high humidity conditions (bathrooms, damp mobile homes).
-
Periodically check the condition of the power cord. If the power cord is damaged, it should be replaced by a specialist repair facility in order to avoid a hazard.
-
Do not use the appliance with a damaged power cord or if it has been dropped or damaged in any other way or is not working properly. Do not repair the device yourself, as it may cause electric shock. Return the damaged device to the appropriate service center for inspection or repair. Any repairs may only be made by authorized service points.
Improperly performed repair may result in serious danger to the user. -
Place the device on a cool, stable, level surface, away from hot kitchen appliances such as: electric cooker, gas burner, etc…
-
Do not use the device near flammable materials.
-
The power cord must not hang over the edge of the table or touch hot surfaces.
-
Before cleaning or after use, remove the plug from the mains socket by holding the socket with your hand. DO NOT pull on the net cord.
-
Do not use the device near water, e.g. in the shower, bathtub or over a wash basin with water.
-
Never wash the appliance under running water or in such a way that water drips into it
-
Do not allow the device to get wet. If the device falls into water, pull the plug out of the socket immediately. Do not put your hands into the water when the device is connected to the mains. It must be checked by a qualified electrician before being used again.
-
Do not handle or use the device with wet hands.
-
The device should be turned off each time after finishing work.
-
Do not leave the device connected to the socket unattended.
-
For additional protection, it is advisable to install a residual current device (RCD) in the electrical circuit with a rated residual current not exceeding 30 mA. Please consult an electrician for this.
-
Before you turn on the device, make sure that all parts are installed correctly.
-
WARNING: Be careful when handling the blades cutting blades, when emptying and cleaning the machine.
-
WARNING: Always unplug the appliance when left unattended and before assembling or disassembling or cleaning.
-
WARNING: Do not use the equipment if the rotating blades are damaged.
-
WARNING: Before replacing equipment or approaching parts that move during use, switch off and disconnect equipment.
-
Only use accessories provided by the manufacturer.
-
When the device is operating, do not put your hand or any objects into the feeder opening. Only use the pusher for this purpose.
-
Meat should be inserted into the feeder opening while the device is operating, it is not allowed to fill the feeder opening with fruit or vegetables when the device is stopped.
-
Be careful not to overload the machine, do not use too much force to push the products through the feeder.
-
Always disconnect the device from the mains when it is not in use or you want to clean it.
-
Do not disassemble the clipper while it is plugged into a power outlet.
-
Do not use harsh scourers or abrasive cleaners for cleaning.
-
Do not immerse the motor unit in water or any other liquid.
Slow Juicer AD 4130 / AD4131
Main Product Unit
-
Power cord with plug
-
Engine unit
-
Swing Switch
-
Locking ring
Extraction function -
Juice cup
-
Foam filter plate
-
Pulp cup
-
Extraction pusher
-
Juice tray
-
Squeezing tube
-
Extraction screw
-
Filter net
-
Extraction cover
Meat grinder Function (Only in AD4131) -
Pusher for meat grinder
-
Food tray
-
Feeding tube
-
Feeding screw
-
Cross knife
-
Cutting disc 3mm
-
Cutting disc 5mm
-
Cutting disc 8mm
-
Fixing ring
-
Sausage attachment
Salad maker (Only in AD4131) -
Salad maker pusher
-
Salad maker tube
-
Salad maker tube cover
-
Slicer
-
Shredder
-
Masher
Before first use
- Before first use remove all packaging material.
- Clean the device and all attachments with warm water mixed with dish washing soap.
- Dry with a dry and soft towel or paper towel.
Button Description:
The device has 1 rocking switch to operate.
The 3 functions ot the switch are as follows;
- 1: This turns on the device. After pressing it Will continue working until turned off.
- O: Off position. The device will be turned off when the switch is in this position.
- R: Reverse. When pressed the engine will turn into reverse. The Auger/slicer will turn in the opposite direction compared to normal operation. When released the device will switch to Off position.
Juice Extractor Models AD4130 and AD4131
Couple Extractor to Frame. (Picture E. Page 3)
Embed the extractor into the frame by aligning the center on the inlet with
the triangle mark (to point at the three fasteners on the extractor). (Picture
E. Page 3)
Then rotate the extractor counterclockwise till it clicks. (Picture E. Page 3)
Align the hexagonal shaft of spiral propeller with the hole in the frame and push it in to the end. (slightly rotate the spiral propeller to make good alignment) (Picture F,G. Page 4)
Insert the coarse-hole end of juice filter into tail of spiral propeller and lock the three fasteners into the three slots in the extractor Mis-align the three fasteners on extractor cover with the three ones on extractor and horizontally push them in, and then attach the cover to the extractor by rotating it counterclockwise. (Picture H. Page 4)
Place juice container beside machine frame with its opening right below the
frame outlet. (Container baffle should be mounted in the container in advance
to block foam in the juice) (Picture H1. Page 5)
Place residue container below the frame residue outlet, near the juice
container. (Picture H2. Page 5)
- Mount tray onto the upper end of inlet cylinder.
- The tray facilities loading of food material, such grape or strawberry.
- Connect to power supply and get ready for startup. Before connecting the device into mains power, make sure the switch is in Off position.)
- Clean the material and cut it into pieces small enough to pass through the inlet, and place them onto the tray.
WARNING:
- Any hard core, seed, skin or shell should be removed in advance. As it might get stuck in the device or block the juice extraction holes.
- Press down the ON button to start then press R button to reverse. Then Press the On button again to start and keep the machine operating for less than 10 minutes.
- Do not to touch the power switch with wet hand to avoid electric shock. leakage or fire.
- Load the food material in through the inlet and push them in with the attached food pusher. DO NOT USE ANY METAL UTENSILS OR OTHER OBJECTS INSTEAD OF THE ATTACHED PUSHER.
- Proper amount of force shall be used to push the food material in, not excessive but sufficient to have it cut off exactly.
- (Do not put your finger or any other object into the inlet! If the residue/juice container is full, disconnect the power supply and empty and then clean before restart.)
- Upon completion, shut down the device by pressing the ON/OFF switch and when no juice flows out of the outlet, disconnect the power supply.
- The extracted juice should be drunk as soon as possible. The longer the juice is exposed to air and sun the less nutritious it will be.
- The remaining pulp should be disposed as fast as possible. Either by throwing it away or it can be dried and used as an fiber supplement. For example apple pulp can be used in baking or making pastries as it has the intense flavor of apples and will not release water and juices into the dough.
- Do not to touch the power switch with wet hands to avoid electric shock, leakage or fire.
MEAT GRINDER (Only AD4131)
Assemble the feeding tube
- Embed the feeding tube into the frame by aligning the center on the inlet with the triangle mark (to point at the three fasteners on the extractor).
- Then rotate the feeding tube counterclockwise till it clicks. (Picture I. Page 6)
- Align the hexagonal shaft of feeding screw with the hole in the frame and push it in to the end. (slightly rotate the spiral propeller to make good alignment) (Picture J. Page 6)
- Put the cross knife onto the feeding screw(there is a 4 angles shape on the front point of feeding screw to place the cross knife. (Picture K. Page 6)
- Put the cutting disc on the feeding screw after placing the cross knife. (Picture L. Page 6)
- Screw the fixing ring on the feeding tube to fix the parts of feeding tube accessory.
- Put the food tray onto the top of feeding tube
- Put the pusher onto food tray, finish the meat grinder function preparation.
Plugged in, prepare for working. Make sure product is on switch-off mode.
Press down ON button to to work.press R button to reverse. start and keep the
machine operating for less than 10 minutes.
Do not to touch the power switch with wet hand to avoid electric shock,
leakage or fire.
Making sausage (Use minced meat to make sausage)
(Please use picture M. Page 6 as an example of correct assembly order):
- Prepare the minced meat
- Remove the fixing ring and put the kebbe attachment & sausage tube, then screw the fixing ring to fix the parts again.
- Connect the sausage wrapper on the sausage tube. Put the minced meat onto feeding tube, then the minced meat will be filled into sausage wrapper. Sausage ready.
Vegetable Slicer (Only model 4131)
- Put the salad maker into the machine, and rotate the locking ring clockwise to lock the salad maker device onto the machine. (Picture N. Page 7)
- Lift up the cover of the salad maker, then select the drum that needs to be used and place it inside the salad maker. (Sometimes it will be advised to move the drum left and right to make the hexagonal screw to fall into proper position before moving to the next step) (Picture O. Page 7)
- Press the lid downwards and apply slight force to ensure that the lid of the salad maker drum is tightly fastened.
- Make sure the On / Off switch is in Off position.
- Plug the device into mains power.
- Press down ON button to turn on the device then press press R button to reverse to make sure the parts are correctly assembled.
- Start and keep the machine operating for less than 10 minutes.
- Do not to touch the power switch with wet hand to avoid electric shock, leakage or fire.
- Place the food into the salad maker tube, and use the pusher to push the food into the salad maker tube.
- Pull out the power plug and put the machine in a power off state.
- Lift up the cover of the salad maker tube.
- Take out the drum. (Picture P. Page 7)
Turn the locking ring counterclockwise, and then remove the salad maker tube from the machine.
Technical data
Maximum working duration: 10 minutes
- Rest time: 30 minutes
- Power: 150 W
- Voltage: 220-240V ~ 50Hz
To protect your environment: please separate carton boxes and plastic bags and
dispose them in corresponding waste bins.
Used appliance should be delivered to the dedicated collecting points due to
hazarsous components, which may effect the environment. Electrical appliance
must be returned in order to reduce its reuse and utilization. If the device
contains batteries they should be delivered to dedicated points separatelly.
AFTER SALE SERVICE NOTICE
If you want to buy spare parts or make any complaints, please contact the seller who issued the receipt directly.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>