H1 ACE R350 Ace E-Scooter Owner’s Manual

ACE R350
Owner’s Manual
Assembly & Maintenance

H-1 PRO SERIES

Thank you for choosing the Hover-1 Ace. It is our pleasure to guide you through setting up your Ace and hitting the road!
Please read through this Owner’s Manual to get familiar with the proper operation of your Ace E-Scooter’s controls, features, capabilities, and limitations.
This manual will be your guide for general maintenance, safety precautions, assembly, and servicing of the unit.
Before riding your Ace E-Scooter, be sure all the parts are properly torqued, tightened, and connected (Particularly the parts that had to be manually installed). Remember to always use your best judgment and obey all traffic laws.
Additional instructions and media will be available to assist you with repairs or maintenance of your Hover-1 Pro Series E-Scooter. Join our H-1 Community of riders wherever you are!

| ridehover1
---|---
| hover1rideables
| hover-1
| @ridehover1
| hover1rideables
| @ridehover1

support@hover-1.com
866.831.1520
www.hover-1.com
DGL Group
2045 Lincoln Highway
Edison, NJ 08817, United States

BASICS

DIAGRAM OF THE ACE GENERAL SYMBOLS
DANGER
Possible dangers to your life and health if respective calls to action are ignored.
WARNING
Warns about a situation that can cause death, serious physical injury and/or heavy material damage if safety instructions are ignored.
NOTICE
Recommendations and meaningful additional information.
SAFETY ADVICE
Please adhere to the following safety instructions while operating your Ace:

• Always wear a properly fitted helmet and protective gear while riding.
• See and be seen. Wear reflective clothing while riding at night.
• Learn the rules of the road before riding. Obey all traffic laws.
• Make sure handlebar grips are not damaged and are properly installed.
• Always check brakes before riding.
• Check for traffic. Always be aware of the traffic around you.
• Watch for and avoid road hazards.
• Reduce speed when riding on wet terrain.
• To prevent skidding or potential injuries, do not accelerate or brake suddenly while making turns.
• To avoid water damage, do not leave your E-Scooter in inclement weather.
• When activating pedal assist, increase speed slowly to avoid injury.
• Do not use and/or leave the charger outdoors in hot or wet weather conditions.
• Do not ride up or down extremely steep inclines.
• Do not touch the body of the motor immediately after riding, as the surface may be hot.
• Do not make any aftermarket modifications to your Ace that are not expressly approved by Hover-1 Pro Series.
• Do not ride the E-Scooter if you exceed the maximum weight limit of 264 lbs.

WARNING
INSTRUCTIONS PERTAINING TO RISK OF FIRE OR ELECTRIC SHOCK – IMPORTANT SAFETY INSTRUCTIONS
WARNING – When using this product, basic precautions should always be followed, including the following:
Read all the instructions before using the product.
To reduce the risk of injury, close supervision is necessary when the product is used near children.
Do not put fingers or hands into the product.
Do not use this product if the flexible power cord or output cable is frayed, has broken insulation, or any other signs of damage.
This equipment is not intended to be used at ambient temperatures less than 0°C (32°F) or above ambient temperatures of 40°C (104°F).
The battery is intended to be charged when the ambient temperature is between 0°C (32°F) and 40°C (104°F). Never charge the battery when ambient temperatures are outside this range.
Modifying or attempting to repair the E-Scooter system except as indicated in the instructions for use and care is prohibited.
Charging of the E-Scooter shall only be performed with the manufacturer’s recommended charger.
SAVE THESE INSTRUCTIONS

SAFETY PRECAUTIONS

PLEASE READ THE OPERATION MANUAL THOROUGHLY.
Failure to follow the basic instructions and safety precautions listed in the operation manual can lead to damage to your Ace, property damage, serious bodily injury, and even death.
Thank you for purchasing the Hover-1 Ace. Please read all instructions carefully before using it and retain this manual for future reference.

• To avoid collisions, falls, and loss of control, please learn how to ride the Ace safely.
• You can learn how to ride the Ace by reading the operation manual and watching videos.
• All users are responsible for any consequences caused by violating warning contents or proper operations. Hover-1 can not be held liable.

ATTENTION

1. Use only the supplied charger from Hover-1 with this E-Scooter.
2. The operating temperature range of the charger is 32°F – 104°F (0°C – 40°C).
3. The operating temperature range of the Ace is 32°F – 104°F (0°C – 40°C).
4. Do not ride on icy or slippery surfaces.
5. Read the operation manual and warning labels before riding.
6. Store the Ace in a dry, ventilated environment.
7. When transporting the Ace, avoid violent crashes or impact.

LOW TEMPERATURE WARNING
Low temperatures will affect the lubrication of moving parts inside the Ace, increasing internal resistance. Additonally, the discharge capacity and capacity of the battery will be significantly decreased.
Use caution when riding the Ace in cold temperatures (Below 40°F/4°C). Doing so may increase the risk of mechanical failures of the E-Scooter, which may lead to damage to your device, property damage, serious bodily injury, and even death.
SAFETY INSTRUCTIONS

• Keep the E-Scooter away from heat sources, direct sunlight, humidity, water, and any other liquids.
• Do not operate the E-Scooter if it has been exposed to water, moisture, or any other liquids to prevent electric shock, explosion, and/or injury to yourself and damage to the E-Scooter.
• Do not use the E-Scooter if it has been dropped or damaged in any way.
• Repairs to electrical equipment should only be performed by the manufacturer.
• Improper repairs void the warranty and may place the user at serious risk.
• Do not puncture or harm the exterior surface of the E-Scooter in any way.
• Keep the device free from dust, lint, etc.
• Do not use this E-Scooter for anything other than its intended use or purpose.
• Doing so may damage the E-Scooter or lead to property damage, injury, or death.
• This product is not a toy. Keep out of reach of children.
• Do not expose the batteries to excessive heat such as direct sunlight or an open flame.
• Do not allow hands, feet, hair, body parts, clothing, or similar articles to come in contact with moving parts, wheels, or the drivetrain while the Ace is running.
• Do not operate or allow others to operate the Ace until the user understands all instructions, warnings, and safety features described in this manual.
• Check with your doctor if you have a medical condition that could affect your ability to use the Ace.
• Persons with head, back, neck ailments, or prior surgeries to those areas of the body are not recommended to use the Ace.
• Do not operate if you are pregnant or have a heart condition.
• Persons with any mental or physical conditions that may make them susceptible to injury or impair their physical or mental capabilities to recognize, understand, and perform all of the safety instructions and assume the hazards inherent in operation should not use the Ace.

WARNING

• When you ride in low-visibility conditions such as fog, dusk, or night, you might be difficult to see, which could lead to a collision. To increase your level of safety, be sure wear bright, reflective clothing when riding in poor lighting conditions.
• As with all mechanical components, the Hover-1 Ace is subjected to wear and high stresses. Different materials and components may react to wear or fatigue in different ways. If the design life of a component has been exceeded, it may suddenly fail, possibly causing injuries to the rider. Any form of crack, scratch, or change of coloring in highly stressed areas indicate that the life of the component has been reached and it should be replaced. Do not ride in an abusive manner.
• Great care should be taken with the Hover-1 Ace when folding or unfolding it. Moving and folding parts can cut skin or pinch if mishandled.

DO NOT RIDE YOUR HOVER-1 Ace WITHOUT ALL RELEASES SECURELY LOCKED.

ASSEMBLY & PARTS

Visually examine your shipping box and E-Scooter to ensure that everything arrived without shipping issues. Take pictures if you suspect rough handling and contact: support@hover-1.com
If you require additional assistance, please reach out to support@hover-1.com for more information. We often update user guides based on the feedback we receive from our customers.
DANGER
Before performing any work on your Ace, be sure the power is OFF.
NOTICE
Be sure the package is upright when opening. Open from the top.
WARNING

• All riders of the E-Scooter should follow these safety instructions.
• Please read all assembly instructions in full before beginning to assemble your new E-Scooter.

Parts List
A. Ace E-Scooter
B. Handlebar Assembly
C. Charger + Charging Cable
D. Hex Keys (2) & M5 Screws (6) SETTING UP YOUR E-SCOOTER
Attaching the Handlebar Assembly
Attach the handlebar assembly by placing it into the steering column. Align the front and back screw holes, and tighten the 6 screws into place using the hex keys provided.
Pinch Points
Some parts of your Hover-1 Ace can injure you if mishandled.
Moving and folding parts can cut skin. Clamps and pivoting parts such as brake levers can pinch. When folding and unfolding your Hover-1 Ace, Please watch for pinch points where injury may be sustained. Do not leave your hand in these areas while folding or unfolding.
Folding & Unfolding Your E-Scooter
To fold your Ace, pull the folding hinge release button up and push the folding hinge down. Push the steering column down to the rear fender.
Align the folding hook with the slot in the rear fender and push the folding hook into it to lock the Ace in a folded position.
To unfold your Ace, push down on the rear fender slot to unlock the folding hook. Raise the steering column up until it is pointing straight up and clicks into place. Pull the folding hinge up and press it against the steering column to ensure it is securely locked.

SAFETY CHECKLIST

WARNING
Please be sure all the items you installed are properly torqued, tightened, and connected! If you have any questions, please contact us: support@hover-1.com 
To be sure your E-Scooter is safe on the road, please use the following checklist before your first ride:

1. Handlebars
   Check that the handlebars are tight by applying the front brake and pushing the handlebars forward and back.

2. Tires
   Check the condition of the tires. Check the tire treads for cracks, punctures, and deformations.
   NOTICE
   Tire wear and tear depends on several factors, such as the weight of the rider and type of terrain.

3. Battery
   Check that the battery is inserted securely.
   Check that the battery is fully charged.
   NOTICE
   Follow battery charging and maintenance instructions.

4. Brakes system
   Pull both brake levers. You should feel an obvious pressure and the levers should not be able to touch the handlebar.

5. Lighting
   Check if the headlight and taillight are working properly.
   NOTICE
   Do not cover any lighting fiixtures or refilectors.

6. Display
   Check if your display turns on and functions properly.

7. Kickstand
   Check if the kickstand is tightly secure, not rubbing against the ground or tires.
   NOTICE
   Do not sit on the E-Scooter if the kickstand is engaged.

SAFETY PRECAUTIONS

• The first rule of safe riding is to use common sense.
• Different localities and countries have different laws about riding electric transportation devices on public roads. You should check with local officials to ensure you are complying with local traffic law requirements.
• Hover-1 is not liable for tickets or violations given to riders who do not follow local laws and regulations.
• For your safety, always wear a helmet that meets CPSC or CE safety standards. In the event of an accident, a helmet can protect you from serious injury and in some cases, even death.
• Obey all local traffic laws. Obey red and green lights, one-way streets, stop signs, pedestrian crosswalks, etc.
• Ride with traffic, not against it.
• Ride defensively; expect the unexpected.
• Give pedestrians the right-of-way.
• Do not ride too close to pedestrian. Alert them if you intend to pass them from behind.
• Slow down at all street intersections and look to the left and right before crossing.
• Your Ace electric folding scooter is not equipped with reflectors. It is not recommended that you ride in conditions of low visibility.
• If you are riding your E-Scooter in low-visibility conditions, ensure your headlight is turned on, and that you are wearing bright, reflective clothing.
• When you ride in low-visibility conditions such as fog, dusk, or night, you might be difficult to see, which could lead to a collision. To increase your level of safety, be sure to wear bright, reflective clothing when riding in low-visibility conditions.
• Do not ride above your skill level. Ensure you have had enough practice with all functions and features of your Ace.
• Do not ride too fast – with increased speed comes increased risk. If you are moving at a higher speed, small bumps can create strong impacts, leading to a higher risk of injury.
• Do not ride with pets.
• Before stepping on your Ace, make sure it is placed flat on level ground.
• Do not try to open or modify your Ace E-Scooter. Doing so voids the manufacturer warranty and may cause your Ace to fail, resulting in injury or death.
• Do not use the Ace in a manner that would put people or property in danger.
• If you are riding near other riders, be sure to maintain a safe distance between each other to prevent collisions.
• Be sure to keep your feet on the Ace at all times. Moving your feet off the Ace while driving is dangerous and may cause the Ace to stop suddenly or veer sideways.
• Do not operate the Ace while under the influence of drugs or alcohol.
• Do not operate the Ace when you are restless or sleepy.
• Use your best judgment to keep yourself out of dangerous situations with your Ace.
• Do not ride your Ace off of curbs, ramps, or attempt to operate in a skate park, empty pool, or in any way similar to a skateboard. Misuse of your Ace voids the manufacturer warranty and may lead to injury or damage.
• Do not abuse your Ace. Doing so can damage your unit and cause failure to the operating system, which may lead to injury. Physical abuse, including dropping your Ace, voids the manufacturer warranty.
• Do not operate in or near puddles of water, mud, sand, stones, gravel, debris, or near rough and rugged terrain.
• The Ace can be used on paved surfaces that are flat and even. If you encounter uneven pavement, lift your Ace over and past the obstruction.
• Do not ride in inclement weather: snow, rain, hail, sleet, on icy roads, or in extreme heat or cold.
• Bend your knees when riding on bumpy pavement to absorb the shock and vibrations. This will help you keep your balance.
• If you are unsure if you can safely ride on a specific terrain, step off and carry your Ace. Always be on the side of caution.
• Proper use of your brake is vital to ensure safe, efficient stopping. To avoid misuse and potential injury, do not apply sudden or excessive force to your brakes. Apply your brakes gradually and give yourself enough room to come to a complete stop safely.
• Do not attempt to ride over bumps or objects greater than ½ inch, even when prepared and bending your knees.
• Pay attention. Look where you are riding and be conscious of the road conditions, people, property, and objects around you.
• Do not operate the Ace in crowded areas.
• Operate your Ace with extreme caution when indoors, especially around people, property, and narrow spaces.
• Do not operate the Ace while talking, texting, or looking at your phone.
• Do not ride your Ace where it is not permitted.
• Do not ride your Ace near motor vehicles or on public roads.
• Do not travel up or down steep hills.
• The Ace is intended for use by a single individual, DO NOT attempt to operate the
• Ace with two or more people.
• Do not carry anything while riding the Ace.
• Individuals with lack of balance should not attempt to operate the Ace.
• Young children and the elderly should not operate the Ace.
• At higher speeds, always take longer stopping distances into consideration.
• Do not attempt to jump on or off your Ace.
• Do not attempt any stunts or tricks with your Ace.
• Do not ride the Ace in dark or poorly lit areas.
• Do not ride the Ace near or over potholes, cracks, or uneven pavement or surfaces.
• Do not operate your Ace off-road.
• Do not turn sharply, especially at high speeds.
• Do not exceed the maximum weight limit of 264 lbs (120 kg).
• Avoid driving the Ace in unsafe places, including areas with flammable gas, steam, liquid, dust, or fiber that could cause fire and explosion accidents.
• Do not operate near swimming pools or other bodies of water.
• Maintain a safe braking distance during wet conditions.
• There may be additional risk to injury if you use your scooter incorrectly. This includes, but is not limited to:
  • Jumping your E-Scooter
  • Riding over debris or obstacles
  • Performing stunts
  • Riding in off-road terrain
  • Riding fast
  • Racing other riders
  • Riding in an unusual manner
• The aforementioned examples add stress to each part of your E-Scooter and can lead to long term damage of the device. Damage to your E-Scooter can lead to an accident or increase your risk of injury. To decrease your risk of injury, use your E-Scooter correctly.
• To reduce the risk of injury, adult supervision is required. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools, or other bodies of water. Always wear shoes, and never allow more than one rider at a time.
• If a system error occurs or an improper operation is performed while riding your Ace, the device will alert the user in a variety of ways. The following are common occurrences that will produce safety alerts. These notices should not be ignored and appropriate action should be taken to correct any improper operation, failure, or errors:
  • Prohibited riding surfaces (Uneven, too steep, unsafe, etc.)
  • Battery voltage is too low.
  • The E-Scooter is still charging.
  • The E-Scooter is overheating, or the motor temperature is too high.
  • When the battery is about to run out of power, the battery icon will flash.
  • If any or both tires are blocked, the device will stop after 10 seconds.
  • When the battery level has depleted below protection mode, the motor  will power off after 15 seconds.
  • If a high discharge current is produced during use (Such as riding up a  steep slope for a long period of time), the motor will shut off after 15 seconds.

OPERATIONS

BEFORE RIDING

• Before each operation, the operator shall perform the pre-operation checks specified below:
• All guards and pads originally supplied by the manufacturer are in proper place and in serviceable condition.
• The area that the unit is to be operated in is safe and suitable for safe operation.
• The braking system is functioning properly.
• All safety labels are in place and understood by the operator and any passenger.
• Any and all axle guards, chain guards, or other covers or guards supplied by the manufacturer are in place and in serviceable condition.
• The tires are in good condition, inflated properly, and have sufficient tread remaining.

WARNING
Any Ace that does not work properly can cause you to lose control and fall. Do not ride a Ace with a part that is damaged. Replace the damaged part before riding.
It is important that you fully understand all the functions of your Ace E-Scooter. If these fuctions are not used correctly, you will not have full control of your Ace.
Practice using the Ace at slower speeds in a flat, open area before taking it out into public areas.
PRE- RIDE CHECKLIST

• Ensure that your Ace is in proper working order each and every time you ride. If a part of the Ace E-Scooter does not function correctly, please contact our Customer Support Center.
• Ensure the battery is fully charged before riding your E-Scooter.
• If the Ace E-Scooter is not used for an extended period of time, you may need to recharge the battery every 2 months to maintain the battery life.
• Please wear all appropriate safety gear before operating your device.
• Make sure to wear comfortable clothes and flat, closed-toe shoes when operating your device.

SPEED MODES
To activate different speed modes, ensure the Ace is powered on and not in motion. Press the power button once. The speed mode indicator should light up on your display to indicate which speed mode is activated.
S: Sport mode: 0-16 MPH (0-26 KM/H)
D: Drive mode: 0-12 MPH (0-19 KM/H)
E: Eco mode: 0-8 MPH (0-13 KM/H)
P: Walk mode: 0-2 MPH (0-3 KM/H)

CRUISE CONTROL
Cruise control comes preset as active with the Hover-1 Ace. To engage cruise control, you just need to press the throttle down for 6 seconds, and cruise control will automatically activate. You will hear 2 beeps, and the cruise control indicator will flash on the display to indicate that it is activated. Press the throttle down once or squeeze the brake handle to cancel cruise control. You can quickly press the power button 4 times to disable or re- enable the cruise control function.
KICK TO START
For safety reasons, the E-Scooter will not accelerate unless it is already moving at least 1.8 mph (3 km/h). You must first kick off the ground and then press the throttle in order to ride the E-Scooter.
RIDING YOUR Ace E- SCOOTER
FAILURE TO FOLLOW ANY OF THE FOLLOWING SAFETY PRECAUTIONS CAN LEAD TO DAMAGE TO YOUR DEVICE, VOID YOUR MANUFACTURER WARRANTY, LEAD TO PROPERTY DAMAGE, CAUSE SERIOUS BODILY INJURY, AND CAN LEAD TO DEATH.
OPERATING YOUR DEVICE
Make sure the device is fully charged before the first use. Before turning on your Ace E-Scooter, ride it like a normal kick scooter to get comfortable with the device before using it with the motor.
When you are comfortable riding the E-Scooter, power it on. For the motor to activate, you must first start riding the E-Scooter manually and then push the throttle down with your thumb.
To slow down, disengage the throttle and squeeze the brake handle to engage the disk brake. The brake is pressure-sensitive, so a tighter squeeze will provide more stopping power.
Use the handlebars to turn in the desired direction.
The Ace E-Scooter can be operated manually if you do not wish to use the motor.
Quickly press the power button two times to turn the headlight on/off. Quickly press the power button three times to switch units between KM/H and MPH.
Quickly press the power button six times to switch between the odometer and the trip mileage.
At higher speeds, you may need to shift your weight to maintain your balance while making turns.
Prepare to brace yourself if you encounter bumps or uneven surfaces, then dismount and carry your Ace to a safe operating surface.
WARNING
Do not turn sharply or at high speeds. Do not turn or ride quickly along slopes, as it may cause injury. Proper use of your brake is vital to ensure safe, efficient stopping. To avoid misuse and potential injury, do not apply sudden or excessive force to your brake. Apply the brake gradually and give yourself enough room to come to a complete stop safely.
SPEED & WEIGHT LIMITATIONS
Speed and weight limits are set for your own safety. Please do not exceed the limits listed in the “SPECIFICATIONS” section of this manual (Page 37).
WARNING
Riding the Ace while exceeding the weight limit may increase the possibility of injury or product damage.
OPERATING RANGE

• The Ace can travel up to 20 miles on a fully charged battery under ideal riding conditions. The following are some of the major factors that will affect the operating range of your device:
• Terrain: Operating Range is highest when riding on a smooth, flat surface. Riding uphill and/or on rough terrain will reduce operating range significantly.
• Weight: A lighter user will have higher operating range than a heavier user.
• Ambient temperature: Please ride and store the E-Scooter in recommended temperatures. This will increase the operating range, battery life, and overall performance of your device.
• Speed and Riding Style: Maintaining a moderate and consistent speed while riding produces maximum operating range. Traveling at high speeds for extended periods of time, frequent starts and stops, and idiling will decrease operating range.

H-1 PRO SERIES APP
Connect the Device

• Open Apple’s App Store or Google Play Store and search “H-1 Pro Series.”
• Open the app and select “sign up” or “log in”.
• Complete any updates that are prompted.
• Click the button on the top right hand corner (+) to add a device.
• Click “Auto Scan” at the top of the screen and turn on your E-Scooter.
• Select the “Enable Bluetooth”, and then select “Start Scanning”.
• When a connectable device appears, select “Next”.
• Once the connection is established, it will automatically add the device to the home page. The next time you open the app, you can directly select the device.
• Lastly, select “done” to finish connecting your device.

Disconnect the Device

• Select the icon “ ” on the top right corner of the app product screen.
• Select the “Remove Device” button at the bottom.
• Lastly, select “Disconnect and wipe data” to remove the device from the app product panel.

LED DISPLAY ERROR CODES
The electronics system has the ability to self-diagnose and report a limited set of errors. Errors will appear on the screen as error codes.
The chart below explains the meaning of each error code:
ADVANCED MATRIX DISPLAY – ERROR CODE CHART

controller.
E2| Accelerator Error| Accelerator assembly failure, or communication error with the controller.
E3| Communicatio Error| Communication error between the instrument panel and the controller.
Damaged wire or loose connector, or faulty instrument panel or controller.
E6| Over Voltage Protection| Battery voltage is too high.
Battery has a fault.
E7| Hall Error| Loose/disconnected motor connector, damaged motor wire, or faulty motor.
E9| Controller Error| Controller error. Restart the scooter.

MAINTENANCE

• To avoid damage to the Ace’s internal circuitry, do not expose it to liquid, moisture, or humidity.
• Do not use abrasive cleaning solvents to clean the Ace.
• Do not expose the Ace to extremely high or low temperatures, as this will shorten the life of the device, destroy the battery, and/or distort certain plastic parts.
• Do not dispose of the Ace in fire as it may explode or combust.
• Do not let the Ace come into contact with sharp objects, as this will cause scratches and damage.
• Do not let the Ace fall from high places, as doing so may damage the internal circuitry.
• Do not attempt to disassemble the Ace.
• Use only the charger provided by Hover-1.
• Use only the manufacturer’s authorized replacement parts.

WARNING

• Avoid using water or other liquids for cleaning. If water or other liquids enter the Ace, it will cause permanent damage to the internal components.
• Users who disassemble the Ace without permission from Hover-1 will void the warranty.

BATTERY SPECIFICATIONS
Battery Type: Rechargeable lithium-ion battery
Charge Time: Up to 6.5 hours
Battery Voltage: 36V
Battery Capacity: 7.8Ah
Working Temperature: 32°F – 104°F (0°C – 40°C)
Charging Temperature: 32°F – 104°F (0°C – 40°C)
Storage Time: 1 year
Storage Temperature: 32°F – 104°F (0°C – 40°C)
Storage Humidity: 5% – 95%

BATTERY MAINTENANCE

• The lithium-ion battery is built into the Ace. Do not disassemble the Ace to remove the battery or attempt to separate it from the Ace.
• When charging the Ace, only use the enclosed 1-pin charging cable provided by Hover-1. Use of any other charger or cable may lead to damage to the Ace, overheating, and risk of fire. Use of any other charger or cable voids the manufacturer warranty.
• Do not connect or attach the Ace or the battery to a power supply plug or directly to a car’s cigarette lighter.
• Do not place the Ace near a fire or leave it out in direct sunlight. Heating the Ace can break or ignite the battery inside the device.
• Do not continue charging the battery if it does not recharge within the specified charging time. Doing so may cause the battery to become hot, rupture, or ignite.
• To preserve natural resources, please recycle or dispose of batteries properly. This product contains lithium-ion batteries. Local, state, or federal laws may prohibit disposal of lithium-ion batteries in ordinary trash. Consult your local waste authority for information regarding available recycling and/or disposal options.

WARNING

• Failure to follow the safety precautions listed below could lead to serious bodily injury and/or death.
• Do not attempt to modify, change, or replace your battery.
• Do not use your device if the battery begins to emit odor, overheats, or begins to leak.
• Do not touch any leaking materials or breathe fumes emitted.
• Do not allow children or animals to touch the battery.
• The battery contains dangerous substances. Do not open the battery or insert anything into the battery.
• Do not attempt to charge the device if the battery has discharge or emits any substances. In that case, immediately distance yourself from the battery in case of fire or explosion.

WARNING
SEEK IMMEDIATE MEDICAL ASSISTANCE IF YOU ARE EXPOSED TO ANY SUBSTANCE THAT IS EMITTED FROM THE BATTERY.
CHARGING YOUR Ace

• Ensure that the charging port is clean and dry.
• Make sure that there is no dust, debris or dirt inside the port.
• Plug the charger into a grounded wall outlet.
• Connect the cable with the power supply.
• Align and connect the 1-pin charging cable into the charging port of the Ace
• E-Scooter (DO NOT FORCE OR BEND THE CHARGING CABLE AS IT MAY CAUSE THE PRONGS TO BEND OR BREAK).
• The charging indicator light on the charger itself should change to RED, indicating that your device is now being charged.
• When the red indicator light on your charger changes to green, then your device is fully charged.
• After fully charging your Ace, unplug the charger from your device and from the power outlet.

DANGER
Only use the included charging cable and charger to charge your Ace.
Using any unauthorized charger may damage your Ace.
SPECIFICATIONS
Model: H1- ,ACE3
Net Weight: 39.68 lbs (18kg)
Max Supported Weight: 264 lbs (120kg)
Min Supported Weight: 40 lbs (18kg)
Max Speed: Up to 16 mph (25.74 km/h)
Max Range: Up to 20 miles (32.18 km)
Battery Type: Lithium-ion
Rated Power: 350W
Max Power: 450W
Battery Voltage: 36V
Battery Capacity: 7.8Ah
Power Requirement: 100V-240V, 50 Hz/60 Hz
Folded Size: 46.6 in. x 8.2 in. x 20.4 in. (118.4 cm x 21 cm x 52 cm)
Open Size: 46.6 in. x 20 in. x 45.9 in. (118.4 cm x 51 cm x 116.6 cm)
Tire Type: Self-Sealing Tubeless Tires
Tire Size: 10” Front & Rear
Brake Type: Front Drum & E-Brake
FCC ID: 2AANZBSS
BT ID: D061001

FCC STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a  Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARRANTY

This warranty is non-transferable and is limited to the original purchaser only. It is not transferable to any subsequent purchaser. The manufacturer warranty only applies to products purchased through an authorized Hover-1 retailer. Any items purchased from private sellers, online auction sites (Including eBay, liquidators, or items sold “as-is” or “final sale”), or from clearance or going-out-ofbusiness sales are not covered by the warranty. The warranty period begins on the date of receipt. Please retain a copy of yourreceipt as this will be required to prove the date of purchase should a warranty claim be activated.
Warranty in effect

1. Hover-1 reserves the right to exchange the returned product for a replacement product of equal or greater value if it is deemed that the product cannot be repaired within a reasonable time or at a reasonable cost. The warranty will be ful fiilled on a case-by-case basis at Hover-1 Pro Series’s discretion. Products and/or parts that have been replaced or exchanged become the property of Hover-1 Pro Series.
2. Warranties that have been activated do not cause the warranty period to be extended, nor do they trigger a new warranty period. The warranty period for replacement parts installed ends with the warranty period for the entire product.
3. The manufacturer’s responsibility shall be limited to the repair or replacement of the product at its sole discretion.

The warranty excludes

1. Physical abuse, improper installation, modifiication, or repairs done by an unauthorized third party.
2. The manufacturer will not take any responsibility if the unit’s failure has resulted from accidents, abuse, misuse, or unauthorized repair, modifiication, or disassembly.
3. Overcharging or damages due to improperly maintaining the lithium-ion battery installed in the unit.
4. Tires, charge ports, or other parts which are considered consumables such as glass or plastic or defects based on normal wear and tear.
5. Marginal differences compared to the target appearance and workmanship provided, as these have negligible effects on the product’s fiitness for use.
6. Damage to the product caused by chemical or electrochemical effects, water, moisture, debris, or abnormal conditions.
7. Acts of God.

The warranty will be considered void if:

1. You use any charger other than a genuine Hover-1 Pro Series charger or the charger designed for your specifiic model as this could pose a risk of a serious fiire hazard.
2. Repairs or modifiications are performed without the written consent of Hover-1 Pro Series or if a Hover-1 Pro Series product is equipped with additional parts or accessories not approved for the product by Hover-1 Pro Series.
3. The E- Scooter is exposed to water, moisture, mud, dirt, or debris.
4. Units have missing or unreadable serial numbers.

Hover-1 Pro Series is not liable for accidental, indirect, or other consequential damage of any kind, which leads to usage restrictions, data loss, and loss of earnings or interruption to business. If you have purchased an extended warranty, please contact the seller for assistance.
Any further claims are excluded, including those for replacement due to damage caused to the outside of the product, provided there is no obligatory legal liability.
Submitting a warranty claim

1. To take advantage of your warranty services, please submit a ticket to the Hover-1 Pro Series Customer Support by visiting www.hover-1.com

2. Hover-1 Pro Series will attempt to diagnose and resolve your issue.
   Hover-1 Pro Series may require photos and/or videos to properly diagnose the issue and verify warranty eligibility. A copy of your receipt or online order confirmation with the purchase date, seller, and item name visible is required. Hover-1 Pro Series reserves the right to verify purchases with the retailer and/or asset protection databases. Warranty claims will be denied if the receipt is invalid, cannot be verified, or if the item has been returned or exchanged. If it is determined that a valid warranty claim exists. Hover-1 Pro Series may send replacement parts or issue an RMA number (Return Material Authorization) to return the damaged product as Hover-1 deems appropriate.

3. If an RMA is issued, the package must be shipped within 14 days of the RMA issuance. If a package is received outside of this time frame, the package will be refused and returned to the sender.

4. In the event that Hover-1 Pro Series technicians find that the product lacks a manufacturer defect, and the malfunction is due to abuse, water damage, debris, moisture exposure, or improper maintenance, the customer will be charged for return shipping and no repairs will be performed.

Hover-1 Pro Series will only accept parcels that have been assigned an active RMA number.
YOU EXPRESSLY UNDERSTAND AND AGREE THAT, TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HOVER-1 PRO SERIES’ TOTAL LIABILITY IN CONNECTION WITH THE APPLICABLE HOVER-1 PRO SERIES’ PRODUCTS OR THIS WARRANTY POLICY WILL NOT EXCEED THE AMOUNT ORIGINALLY PAID FOR THE PRODUCT. PARTS AVAILABILITY IS NOT GUARANTEED.

AFFIX SERIAL NUMBER LABEL HERE:
REGISTER YOUR ACE
AT HOVER-1.COM
AFFIX SERIAL NUMBER LABEL HERE:
CHARGER TYPE: ES9
DGL Group
2045 Lincoln Highway
Edison, NJ 08817
support@hover-1.com
hover-1.com

References

• Hover-1™ Rideables™ – Hover-1 Rideables

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>