alpho DPX Power Source Enclosure System Owner’s Manual
- June 13, 2024
- alpho
Table of Contents
DPX Power Source
Enclosure System
DPX Power Source Enclosure System
- Compact footprint ideal for ground mount installations in Right-of-Way for small cell applications
- Provides power for up to 10 small cell nodes from a single grid tap connection
- Wide AC input voltage range (90 to 305 Vac) for worldwide deployment
- Type 3R rated outdoor cabinet with heat exchanger for improved energy efficiency and reduced maintenance costs
- Optional energy storage enclosure available
The DPX Power Source enclosure system is part of the distributed power
transport product family specifically engineered using the new Alliance for
Telecommunications Industry Solutions (ATIS) fault managed power distribution
technology.
The DPX Power Source enclosure system is housed in a Type 3R rated enclosure
and designed for pole and ground mount installations. The enclosure system can
remotely power up to 10 small cell nodes from a single grid tap connection.
Optional energy storage cabinet is available to support additional backup
time.
Local and remote setup, adjustment and control is a simple single-step process
with the system controller. By utilizing TCP/IP technology, complete
configuration and monitoring of power equipment is possible through a network
web browser or via local isplay.
Distributed power transport architecture enables operators to deploy their
network faster by eliminating the need to have AC utility power at each small
cell location. At a central location, the central power hub converts the
incoming AC power to fault managed power which is transported over a hybrid or
copper only cable to a disconnect box and then to a down converter device
located approximately 6000 ft away. This reduces installation and operating
expenses, and provides flexibility related to site selection for the
installation of the remote communications equipment
DPX Power Source Enclosure System
Consult your Alpha® sales representative for system configurations.
Electrical
Input Voltage| Nominal: 208 to 277 Vac
Operating: 187 to 305 Vac
Extended: 90 to 187 Vac (derated power)
Input Frequency| 45.0 Hz to 66.0 Hz
Power Factor| >95% (10 to 100% load)
THD| <5% (50 to 100% load)
Output Voltage| ±190 Vdc
Output Power| 10 × 2000 W channels
Acoustic| <65 dbA
Features
Protection| •Pad-lockable door handles
•1 x 20kA AC surge suppression
•10 x 20kA DC surge suppression
Energy Storage Support Options| • AlphaCap 665 for short duration backup of
Cordex® CXC HP controller
• PowerSafe® SBS 190F batteries installed inside PSE for backup, up to 5
channel outputs
•Energy storage enclosure for extended backup
Mechanical
Dimensions H × W × D| Overall: 1232 × 1016 × 889 mm (48 × 40 × 35 in.)
Footprint: 1232 × 1016 × 610 mm (48 × 40 × 24 in.)
Weight| 180 kg (397 lb)
Mounting| •Ground
•Pole (no battery application)
Cooling| 130 W/◦C (72 W/◦F) Heat Exchanger
Environmental
Temperature| Operating: –40 to 46°C (–40 to 115°F); plus solar loading
Storage: –40 to 85°C (–40 to 185°F)
Relative Humidity| 5 to 95% non-condensing
Elevation| Up to 3,000 m (9,842 ft)
Cabinet Rating| Type 3R
Agency Compliance
Safety| •CSA-US Field Evaluation
•ATIS (Pending)
•CSA/UL 62368-1 (Pending)
© 2023 EnerSys. All rights reserved. Trademarks and logos are the property of EnerSys and its affiliates unless otherwise noted. Subject to revisions without prior notice. E.&O.E
EnerSys World Headquarters
2366 Bernville Road,
Reading, PA 19605, USA
Tel: +1-610-208-1991
+1-800-538-3627| EnerSys EMEA
EH Europe GmbH,
Baarerstrasse 18,
6300 Zug
Switzerland| EnerSys Asia
152 Beach Road,
Gateway East Building #11-08,
Singapore 189721
Tel: +65 6416 4800
---|---|---
09/2023
#0480092-00 REV A
Documents / Resources
|
alpho DPX Power Source Enclosure
System
[pdf] Owner's Manual
DPX Power Source Enclosure System, DPX, Power Source Enclosure System, Source
Enclosure System, Enclosure System
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>