Connect IT CI-24 Universal Wall Mount For Projector Instruction Manual

Cl-24
INSTALLATION INSTRUCTIONS

UNIVERSAL WALL MOUNT FOR PROJECTOR

CI-24 Universal Wall Mount For Projector

NOTE: Read entire instruction sheet before you start installation and assembly.

WARNING

• Do not begin the installation of the product before you have read and understood the instructions and warnings contained in this installation sheet. If you have any question regarding any of the instruction or warning, Please contact your local distributor.
• Please refer to the installation guide recommendation for required distance from wall to avoid risk of property damage.
• This product should only be installed by someone of good mechanical aptitude, with experience and basic building, and fully understands.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the maximum load capacity.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the items, greatly reducing their holding power.
• This product intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

Component Checklist

IMPORTANT: Ensure you have received all parts against the component checklist prior to installing. If any parts are missing or faulty, telephone the special franchiser for a replacement.

Package M

Package W

Tools required

• Phillips Head Screw driver(200mm length exclude the handle)
• Socket and Wrench
• Electric drill and 10mm masonry bit for concrete wall installation
• Marking Pen
• Hammer

The Cable Management

• Disassemble the adjustable rod for easy cable management.
• Loosen the clamp plate screw with a 5mm Allen key (M-K) .Then pull out the inner rod from the adjustable rod as shown in fig.1.1.
• Loosen three screws with a proper screwdriver and remove the bottom plate from the inner rod.
• Run the cable through the channel as shown in fig. 1.2.
• Insert the bottom plate into the inner rod and tighten three screws as shown in fig.1.3.
• Install the inner rod into the outer rod as shown in fig.1.3.

Installing Projector Ceiling Mount Assembly

Attach the adjustable rod to the ceiling plate with four screws (M-B) and four washers (M-l) as shown in fig.2.1.

Insert the pivot bracket into the end of inner rod and secure with four screws (M-A) and four washers (M-H) as shown in fig.2.2.

WOOD STUD WALL MOUNTING:

WARNING

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Tighten wood screws firmly, but do not over tighten. Over tightening can damage the screws, greatly reducing their holding power.
• Make sure that mounting screws are anchored into the center of the studs. Use of an “edge to edge’ stud finder is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into studs. Installers are responsible to provide hardware for other types of mounting situations.
• Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down the stud’s center.
• Place the ceiling plate on the ceiling as a template. And mark the center of the two mounting holes. Make sure that the mounting holes are on the stud centerline.
• Drill two 1/8” (3mm) dia. Holes 1.2” (30mm) deep. Make sure that the ceiling plate is level, secure it using two lag bolts (W-A) as shown in fig. 3.1.

SOLID BRICK AND CONCRETE BLOCK MOUNTING:

• When installing projector ceiling mounts on cinder block, verify that you have a minimum of 1-3/8” of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1” minimum from the side of the block. It is suggested electric drill on slow setting is used to drill the hole instead of ahammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Use the ceiling plate as a template to mark four holes locations on the ceiling as shown in fig.3.2.
• Pre-drill these holes with a 10mm masonry bit to at least 60mm in depth. Insert a concrete anchor (W-B) into each of these holes. Attach the ceiling plate to the ceiling using four lag bolts (W-A) and four washers (W-C) as shown in fig.3.2.

Installing the Adapter Bracket

• Place the projector upside down, place adapter bracket on the back of projector, as close as possible to projector center of gravity, using one arm for each mounting hole, position the holes of arms over mounting holes, You can replace the channel foot according to mounting holes position as shown in fig.4.1.

Note: If there are only three mounting holes using three arms of adapter bracket.
Important: If the projector does not have at least three mounting holes, do not use this adapter bracket.

• Attach the adapter bracket to the back of the projector using the appropriate combination of screws, washers, as shown in fig.4.1.
• Begin with the proper screw, hand thread through adapter bracket into the mounting holes of projector..
• Repeat for remaining mounting holes, tighten screws .Do not over tighten.

Hang the bracket mounted projector onto the Assembled Pivot Bracket

You can loosen clamp plate screw with a 5mm Allen key (M-K) to adjust the inner rod to the desired extended position and then tighten clamp plate screw as shown in fig.5.1 .

• Guide hook slots of adapter bracket onto bars in pivot bracket and secure with two screws (M-A) and two washers (M-H) as shown in fig.5.2.
• Cut cable cover to the length of outer rod opening. Snap cable cover into opening as shown in fig.5.2.

Important: Make sure the projector is correctly hooked and the screws are locked safely before loosening the projector.

Pitching angle adjustment

you can adjust your projector to the desired angle, the pitching angle can be adjusted between -15°~+15°, pivot: -10°~+10° as shown in fig.6.1 and fig.6.2.

Maintenance

Once you have mounted the bracket and the projector, check that they are sufficiently secure and safe to use.
You should check whether screws are fixed well each two months. If you have any doubts regarding the installation, please consult our retailer or service department for detail.

MANUFACTURER HERSTELLER PRODUCENT
IT TRADE, a.s.
Brtnická 1486/2 101 00 Praha 10 – Michel
Czech Republic
tel.: +420 734 777 444
service@connectit-europe.com
www.connectit-europe.com

Documents / Resources

| Connect IT CI-24 Universal Wall Mount For Projector [pdf] Instruction Manual
CI-24 Universal Wall Mount For Projector, CI-24, Universal Wall Mount For Projector, Wall Mount For Projector, Mount For Projector, Projector
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>