manhattan 180924 EU 10-Port AC Charging Cabinet Instructions
- June 13, 2024
- Manhattan
Table of Contents
180924 EU 10-Port AC Charging Cabinet
For additional benefits
Scan to register your product warranty or visit: register.manhattanproduct.com/r/180924
For specifications, please visit manhattanproducts.com. Register your product
at register.
manhattanproducts.com/r/180924 or scan the QR code on the cover.
Using the Lock
The Default Combination and Turning the Wheels
The default combination is 0-0-0-0; see below. The wheels are only able to be
turned to the left.
To Unlock
• Combination Method: Turn the wheels to the correct code.
• Key Method: Turn the key in the lock as shown.
Instructions
To Set a New Combination
Remember to record and safely store the new combination after you set it. This
is a
mechanical lock, which cannot be reset directly if the code is forgotten.
-
Make sure the Combination button on the back of the handle is in the Normal position.
-
Push the Combination button to the Set position.
-
Turn the combination wheels to your desired code. NOTE: make sure
to record and securely store the new combination. -
Once the new code is set, push the Combination button back to the Normal position.
NOTE: Make sure you record and securely store the new combination.
To Find the Forgotten Combination
1 Remove the combination wheel box from the handle by unfastening the screws that secure it in place.
2 Turn the combination wheels to the left to find the cutouts on the adjacent
smaller wheels. The number next to the
cutout is the correct number in the combination.
3 Once the correct combination is noted and stored securely, re-fasten the
combination wheel box to the handle using the screws.
Setup
1 Unlock unit door and open it.
2 Fitting a larger device — To remove an appropriate slot divider, push it to the back of the cabinet and lift it out. To replace a divider, position its tab(s) into the appropriate slot(s) and pull it toward you.
3 Connect devices to power outlets with appropriate cables. Secure cables with wire clips on dividers.
- Remove screws that hold the power box in place; slide the power box out.
- Connect power cables to power outlets, feeding cables through holes on power panel.
- Push the power box back in and replace the screws that hold it in place.
- Load devices in bays.
- Connect cables to devices.
Charging
4 Connect unit power cable to power outlet. Unit automatically begins to charge devices.
Instructions
Installation Options
The following sections offer optional steps to complete installation.
Mounting to the Wall
1 At desired location on wall, use the spacing shown in
the graphic below to mark four level drill positions
for the cabinet holes.
Concrete wall: use a 15/64” (6 mm) bit to drill holes
2.4 in. (60 mm) deep at marks.
Wood-stud walls: use a 15/64” (6 mm) bit to make
pilot holes 2.4 in. (60 mm) deep at marks.
2 Install included screws into holes so they protrude
0.4 in. (10 mm) from the wall.
3 Position cabinet holes over wall screws and hang
cabinet on them. Installation is complete.
Stacking the Units — NOTE: Make sure all power is cut off from unit!
Stacking material not included; refer to website.
1 Unscrew the screws on the power box.
2 Slide the power box out.
3 Align the stacking holes on the top and bottom of the cabinets.
4 Tighten screws (not included) into both cabinets
from the ceiling of the bottom cabinet.
5 Reinstall the power box with its screws
WASTE ELECTRICAL & ELECTRONIC EQUIPMENT
Disposal of Electric Equipment (applicable in the E.U. and other countries with separate collection systems)
This symbol on the product or its packaging means that this product must not be treated as unsorted household waste. In accordance with EU Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), this electrical product must be disposed of in accordance with the user’s local regulations for electrical or electronic waste. Please dispose of this product by returning it to your local point of sale or recycling pickup point in your municipality.
WARRANTY
REGULATORY STATEMENTS
This device complies with the requirements of CE 2014/30/EU (UKCA
Electromagnetic
Compatibility Regulations 2016) and / or 2014/35/EU (UKCA Electrical Equipment
[Safety] Regulations 2016). The Declaration of Conformity for is available at:
support.manhattanproducts.com/barcode/180924
North & South America
IC Intracom Americas
550 Commerce Blvd.
Oldsmar, FL 34677, USA
All trademarks and trade names are the property of their respective owners.
© IC Intracom. All rights reserved. Manhattan is a trademark
of IC Intracom, registered in the U.S. and other countries.
References
- Manhattan Products: HDMI Adapters, Cables, TV Mounts, Barcode Scanners
- Manhattan Products: HDMI Adapters, Cables, TV Mounts, Barcode Scanners
- Manhattan Products Account and Product Registration
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>