manhattan 462495 Aluminum Gas Spring Single Monitor Desk Mount Instruction Manual

manhattan 462495 Aluminum Gas Spring Single Monitor Desk Mount

Specifications

• Model: 462495
• Product Name: Aluminum Gas Spring Single Monitor Desk Mount
• Manufacturer: Manhattan

Product Usage Instructions

1. Adjusting the Angle:
   • Use the Allen key provided to tighten the screws.
   • Alternate between each screw as you tighten them for balanced adjustment.
2. Properly Balancing the Arm with Monitors Mounted:
3. Position and firmly hold the arm horizontally.
4. Adjust the spring tension using the supplied Allen Key.

FAQ (Frequently Asked Questions) Q: How do I adjust the angle of the monitor mount?
A: Use the provided Allen key to tighten the screws, alternating between each screw for balanced adjustment.

Q: How do I balance the arm with monitors mounted?
A: Follow these steps:

1. Position and hold the arm horizontally.
2. Adjust the spring tension using the Allen Key provided.

Q: What should I not do when using the product?
A: Do not overtighten the screws to avoid damage to the product.

Important: Read before use.

Safety Precautions

• Avoid potential injuries or property damage! Manhattan is not responsible for damage or injury caused by incorrect assembly or use.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Be sure that you understand all instructions before you begin assembly. Ensure that you have received all parts according to the component checklist prior to installation.
• Safety gear and proper tools must be used. This product should only be installed by professionals.
• Use the mounting screws provided and DO NOT OVER-TIGHTEN mounting screws.
• This product is intended for indoor use only.
• Maintenance: Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• For specifications, go to manhattanproducts.com. Register your product at register.manhattanproducts.com/r/462495 or scan the QR code below.

For additional benefits:

Scan to register your product warranty

or go to : register.manhattanproducts.com/r/462495

Tool Parts

Assembly Instructions

WARNING: Stored energy hazard!

• Firmly hold the two halves of the spring arm together and have another person cut off the cable tie from around the spring arm.
• Slowly release the pressure on the spring arm and allow it to gradually stretch to its full extension.

To properly balance the arm with monitors mounted, adjust the spring tension using the supplied Allen Key:

1. Position and firmly hold the arm horizontally as shown.
2. Turn the adjustment screw until it stays in horizontal position:
   • if the arm drops, turn Counter-clockwise;
   • if the arm rises, turn Clockwise.

Note: Adjust to the desired angle, then use the Allen key to tighten the screws. Alternate between each screw as you tighten them.

WARRANTY AT:

manhattanproducts.com

support.manhattanproducts.com/barcode/462495

North & South America IC Intracom Americas 550 Commerce Blvd. Oldsmar, FL 34677 USA
Asia & Africa
IC Intracom Asia
4-F, No. 77, Sec. 1, Xintai 5th Rd. Xizhi Dist., New Taipei City 221
Taiwan
Europe
IC Intracom Europe Löhbacher Str. 7
D-58553 Halver Germany

All trademarks and trade names are the property of their respective owners. © IC Intracom. All rights reserved. Manhattan is a trademark of IC Intracom, registered in the U.S. and other countries.
Printed on recycled paper.
MH462495 QIG_1123_REV_5.11

References

• Manhattan Products: HDMI Adapters, Cables, TV Mounts, Barcode Scanners
• Manhattan Products Account and Product Registration
• Manhattan Products Account and Product Registration

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>