HINKLEY 59024-LL Brick Mounting Concrete Mounting Lamp Instruction Manual
- June 13, 2024
- HINKLEY
Table of Contents
HINKLEY 59024-LL Brick Mounting Concrete Mounting Lamp
Product Information
- Item: 59024-LL
- Spanish Article: 59024-LL
- Designed to be operated with 120 Volt AC power supply
- Mounting options: Brick Mounting, Concrete Mounting
Product Usage Instructions
Luminaire Mounting
- To prevent electrical shock, disconnect transformer from electrical supply before installation or service.
- Run wire to Luminaire with the use of conduit before installation. The Fixture is provided with four 3/4 NPT conduit openings and one 1 NPT conduit opening. Ensure that all non-used open holes are closed or covered before beginning installation.
- Strip the two wire leads from the Luminaire and connect to the main supply wire using the provided wirenuts.
For Masonry Installation:
- Locate the desired position of the fixture and set it in place with mortar. The fixture should take the place of a standard masonry brick.
- Use zinc-coated steel fasteners to secure the housing. If stainless steel screws are used, apply an anti-corrosion gel to prevent any corrosion to the housing. Warranty may be reduced if this precaution is not taken.
For Poured Concrete Installation:
- Level the supplied template on a wood support frame and drill four 3/16 diameter clearance holes.
- Attach the fixture to the wood support using four No8-32 screws and washers (not supplied) as shown in the illustration.
- Pour concrete.
- Once the concrete has set, remove the wood support frame, wire accordingly, and then attach the fixture faceplate with the four black screws provided with the fixture.
Lamp Replacement
- Remove the four black oxide screws from the faceplate using a Philips head screwdriver.
- Set the faceplate aside for reuse in assembly.
- Remove the burned-out light bulb and replace it with a new one.
- Reattach the faceplate and energize the fixture.
Installation Instructions
SAFETY WARNING: TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITY FOR CODE REQUIREMENTS.
IMPORTANT OPERATION NOTE: THIS LIMINAIRE IS DESIGNED TO BE OPERATED WITH 120 VOLT AC POWER SUPPLY. SAVE THESE INSTRUCTIONS
Luminaire Mounting:
-
To prevent electrical shock, disconnect transformer from electrical supply before installation or service.
-
Run wire to Luminaire with use of conduit before installation. The Fixture is provided with four 3/4” NPT conduit openings and one 1” NPT conduit opening. Ensure that all non-used open holes are closed or covered before beginning installation.
-
Strip the two wire leads from the Luminaire and connect to main supply wire using the provided wirenuts
Common For Masonry Installation: -
Locate desired position of fixture and set in place with mortar. Fixture should take the place of a standard masonry brick. WARNING: It is advised that you use zinc coated steel fasteners to secure housing. If stainless steel screws are used, apply an
anti-corrosion gel to the screws to prevent any corrosion to housing. Warranty may be reduced if this precaution is not taken. For Poured Concrete Installation: -
Level the supplied template on wood support frame and drill four 3/16” diameter clearance holes. Attach fixture to wood support using four No8-32 screws and washers (not supplied) as shown in illustration.
-
Pour Concrete
-
Once concrete has set, remove the wood support frame and wire accordingly and then attach the fixture faceplate with the four Black screws provided with fixture.
Lamp Replacement:
- Remove the four Black oxide screws from the faceplate using a Philips head screwdriver.
- Set faceplate aside for reuse in assembly.
- Remove burned out light bulb and replace with new one
- Reattached faceplate and energize fixture.
Brick Mounting
Concrete Mounting
Lamp replacement
DIMENSION
12600 Berea Road Cleveland, OH 44111 800.446.5539 / 216.671.3300 www.hinkley.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>