HINKLEY 990054Fxx Facet Flush Smart Ceiling Fan with Light Installation Guide
- June 13, 2024
- HINKLEY
Table of Contents
HINKLEY 990054Fxx Facet Flush Smart Ceiling Fan with Light
PARTS
- A) Mounting coupler assembly
- B) Hanger bracket
- C) Canopy
- D) Trim ring
- E) Downrod Asm
INSTALLING THE HANGER BRACKET
REMEMBER -Turn off the power!
Attach hanging bracket to outlet box using screws provided with the outlet box. (Fig.1)
HANGING THE FAN
Step 1. Remove hanger ball from downrod by loosening set screw in the side of the hanger ball. Slide hanger ball down and remove cross pin; remove hanger ball. (Fig. 2)
Step 2. Carefully support the fan motor assembly in it’s styrofoam packing so the top of the motor facing upward.
Step 3. Slip the wires from the fan motor through the mounting coupler assembly, and than tighten mounting coupler assembly to the fan body with four mounting screws. (Fig. 3)
Step 4. Remove the downrod pin from the coupler assembly by removing the cotter pin from the downrod pin. Loosen the two security screws. Carefully feed the electrical lead wires and safety cable from the fan through the downrod. Thread downrod into coupler until holes align. Insert downrod pin through holes in mounting coupler and downrod; clip cotter pin through small hole in end of downrod pin to hold downrod in place. (Fig. 4)
Step 5. Tighten security set screws against downrod using a large flat blade screwdriver to ensure a tight fit against downrod.
Step 6. Slip the wires from the fan motor through the yoke cover, trim ring and canopy. Slide the hanger ball onto the downrod, insert the cross pin through the downrod. Pull the hanger ball up so the cross pin seats in the channel in the hanger ball. Tighten the set screw. (Fig. 5)
SAFETY CABLE INSTALLATION
Step 1. Attach the wood screw and the flat washer to the ceiling joist as shown (do not fully tighten). Slide the cable clamp onto the safety cable from the fan. Loop the safety cable around the wood screw that was just attached to ceiling joist. Feed the end of the cable into the clamp and pull as much cable through as possible. Firmly tighten screw in the clamp. Cut off excess cable and tighten the wood screw to ceiling joist. (Fig.6)
ELECTRICAL CONNECTIONS
WARNINGS: Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire nuts, except for the ground wire.
Connect the supply wires from the ceiling to the receiver unit. (Use the 2 wire bundle on the receiver) Secure with supplied wire nuts.
- Connect the BLACK building supply wire to the BLACK receiver wire.
- Connect the WHITE receiver neutral wire to the WHITE building neutral wire.
- Connect the COPPER building ground wire to the 3 YELLOW/ GREEN ground wires from the fan and receiver.
Turn the wire nut connections upward, spreading them apart so the green (ground) and white wires will be on one side of the outlet box and the black wire will be on the other side. Carefully tuck wires into the outlet box space or evenly around the sides of the hanger bracket.
CEILING CANOPY INSTALLATION
Step 1. Tuck connections neatly into ceiling outlet box. (Fig. 8)
Step 2. Remove one canopy screw on the bracket and slide the canopy up to mounting bracket and place the key hole on screw on the mounting bracket aligning the key slot in the canopy with the canopy screw in the hanger bracket, turn canopy until it locks in place at the narrow section of the key holes.
Step 3. Align the circular hole on canopy with the remaining hole on the mounting bracket, secure by tightening the two set screws.
Step 4. Assemble the trim ring by aligning the two key slots on the top side of the trim ring with the two canopy screws. Twist to lock into place.
Referring to Facet fan installation instruction for other ceiling fan instilling procedure.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>