HINKLEY 46441 Welsh LED 18 inch Black Pendant Ceiling Light Instruction Manual

HINKLEY 46441 Welsh LED 18-inch Black Pendant Ceiling Light

HINKLEY Product Information

HINKLEY is a lighting fixture that provides indoor and outdoor illumination. It consists of a lamp fixture with appropriate medium base bulbs, a shade assembly, and a mounting plate for installation. The product is designed to be installed in various settings, including residential and commercial spaces. It is important to follow the provided instructions for proper installation and usage.

Product Usage Instructions

1. For Indoor Fixtures:
   • Connect the positive supply wire (typically black or the smooth, unmarked side of the two-conductor cord) to the positive fixture lead with an appropriately sized twist-on connector – refer to Drawings 1 or 2.
   • Connect the negative supply wire (typically white or the ribbed, marked side of the two-conductor cord) to the negative fixture lead.
   • Refer to the grounding instructions below to complete all electrical connections.
2. For Outdoor Fixtures:
   • Connect the positive supply wire (typically black or the smooth, unmarked side of the two-conductor cord) to the positive fixture lead with an appropriately sized twist-on connector – refer to Drawings 2 or 3.

**Grounding Instructions

**

It is important to properly ground the HINKLEY lighting fixture for safety purposes. Follow the instructions below:

1. Turn off the power supply during installation.
2. If new wiring is required, consult a qualified electrician or local authorities for code requirements.
3. Follow the wiring and grounding instructions provided in IS 18 (included in the product package).

Mounting Instructions

1. To begin installation it will first be necessary to mount the main body to the junction box. This is accomplished by first preparing the mounting strap (A) for installation – see Drawing 1.

2. Take the mounting strap (A) and locate the two threaded holes (T) in the plate that are the same distance apart as the two holes (E) in the canopy (D) – see Drawing 2.

3. Now take one of the long mounting screws (B), provided, and thread it into hole (T) from the back of the mounting strap.

   • NOTE : The front of the mounting strap has the head of the ground screw showing. Thread the screws down until the head of the screw is approximately 1/8” above the mounting strap. After both screws are in place check to see if the screws will pass through holes in the canopy (E)

4. Mounting strap (A) can now be attached to junction box (J). Use two 8-32 screws (C), 1” long, (NOT PROVIDED), or use the screws from the previous installation – see DRAWING 2

5. The body of the fixture can now be mounted to the junction box. This is accomplished by first making all wiring connections following (instruction sheet IS-18) provided.
   Assistance may be required during this operation.

6. After the iring is complete tuck wires into the junction box and lift the fixture to the filing and align holes (E) in the canopy with screws (B) in the mounting plate. Slip screws through holes and slip canopy up against the ceiling and hold in position

7. Now take barrel knobs (F) and thread them onto the end of screws (B) and tighten until the canopy is tight against the ceiling

Shade assembly (See drawing 3)

1. Lamp fixture with appropriate medium base bulbs (3)
2. Lift shade towards (4) canopy (1)
3. Place the flat washer (6) and plastic washer (7) onto the center pipe (5).
4. Lift shade towards (4) canopy (1)
5. Use finial (9) to secure the diffuser (8) and shade (4) on the center pipe (5).
6. The fixture can now be powered on

Wiring grounding instructions

SAFETY WARNING : READ WIRING AND GROUNDING INSTRUCTIONS (18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

Wiring instructions

Indoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on the connector – see Drawings 1 or 2.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on connector — see Drawings 2 or 3.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Cover the open end of connectors with silicone sealant to form a watertight seal.
   • If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform especially.
4. Please refer to the grounding instructions below to complete all electrical connections.

Grounding instructions

• Flush Mount Fixtures
  For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) – see Drawing 1.

  • Note : On straps for screw supported fixtures, first install the two mounting screws in the strap. Any remaining tapped hole may be used for the ground screw.

• Chain Hung Fixtures
  Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.

• Post-Mount Fixtures
  Connect fixture ground wire (E) (typically copper or green plastic coated) to the power supply ground with an appropriately sized twist-on connector inside the post. Cover the open end of the connector with silicone sealant to form a watertight seal – see Drawing 3.

H I N K L E Y 33000 Pin Oak Parkway, Avon Lake, OH 44012 8 00.446.5539 / 440.653.5500 hinkley.com

References

• HINKLEY - Lighting and Ceiling Fans

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>