HINKLEY 28830 Outdoor Wall Light Instruction Manual
- June 13, 2024
- HINKLEY
Table of Contents
HINKLEY 28830 Outdoor Wall Light
Product Information
The product is a fixture from HINKLEY, model number 28830. It is designed for indoor or outdoor use and comes with mounting instructions. The fixture has a mounting strap (A), universal strap (B), junction box (J), backplate (E), ball knobs (F), front fixture panel (G), and a glass panel (2). The fixture requires a candle base bulb(s) (3) for operation.
Product Usage Instructions
Before starting the installation process, find a clear area to work and unpack the fixture and glass from the carton. Carefully review all instructions prior to assembly.
Mounting Instructions:
- Prepare the mounting strap (A) by threading the two long mounting screws (B) into the back of the universal strap. Refer to Drawing 1 for visual guidance.
- Attach the mounting strap (A) to the junction box (J) using two screws (C) (not provided). Refer to Drawing 1 for visual guidance.
- To mount the fixture, slip the two mounting screws (B) through the two mounting holes (D) in the backplate (E). Refer to Drawing 1 for visual guidance.
- While holding the fixture in place, thread the two ball knobs (F) onto the end of the mounting screws (B) and tighten.
- Open up the front fixture panel (G).
- Place the glass panel (2) into the cage and fold down tabs (1) to lock it into place.
- Install the appropriate candle base bulb(s) (3) into the lamp fixture.
- Close the front fixture panel.
- The fixture can now be powered on.
Note: Ensure to read the wiring and grounding instructions (I.S. 18) and any additional directions provided. Turn off the power supply during installation. If new wiring is required, it is recommended to consult a qualified electrician or local authorities for code requirements.
Wiring Instructions:
Indoor Fixtures:
- Connect the positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to the positive fixture lead (B) using an appropriately sized twist-on connector. Refer to Drawings 1 or 2 for visual guidance.
- Connect the negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to the negative fixture lead (D).
- Refer to the grounding instructions below to complete all electrical connections.
Outdoor Fixtures:
- Connect the positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to the positive fixture lead (B) using an appropriately sized twist-on connector. Refer to Drawings 2 or 3 for visual guidance.
Note: For safety reasons and compliance with code requirements, it is important to read and follow all wiring and grounding instructions provided in the manual.
Mounting Instructions
Item No : 28830
- Find a clear area in which you can work.
- Unpack fixture and glass from carton.
- Carefully review instructions prior to assembly.
- Prepare mounting strap (A) by threading the two long mounting screws (B) into the back of the universal strap – see Drawing 1.
- Be sure the holes into which the screws are threaded match the spacing of holes (D) in the back plate (E).
- Attach mounting strap (A) to junction box (J) using two screws (C). (not provided)
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY
ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW
WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR
CODE REQUIREMENTS
Make electrical connections from supply wire to fixture lead wires. Refer to
instruction sheet (I.S. 18) and follow all instructions to make all necessary
wiring connections. Then refer back to this sheet to complete installation of
this fixture
- To mount fixture, slip the two mounting screws (B) through the two mounting holes (D) in the backplate (E) – see Drawing 1.
- While holding fixture in place, thread the two ball knobs (F) on to the end of the mounting screws (B), and tighten.
- Open up front fixture panel (G)
- Place glass panel (2) into cage and and fold down tabs (1) to lock into place
- Lamp fixture with appropriate candle base bulb(s) (3)
- Close front fixture panel
- Fixture can now be powered on
Wiring grounding instructions
SAFETY WARNING : READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS
Indoor Fixtures
- Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector – see Drawings 1 or 2.
- Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
- Please refer to the grounding instructions below to complete all electrical connections
Outdoor Fixtures
- Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector — see Drawings 2 or 3.
- Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
- Cover open end of connectors with silicone sealant to form a watertight seal.
- If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.
- Please refer to the grounding instructions below to complete all electrical connections.
Grounding instructions
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture
ground wire (E) (typically copper or green plastic coated) to the fixture
mounting strap (M) with the ground screw (S) – see Drawing 1.
Note : On straps for screw supported fixtures, first install the two
mounting screws in strap. Any remaining tapped hole may be used for the ground
screw.
Chain Hung Fixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under
the head of the ground screw (S) on fixture mounting strap (M) and connect to
the loose end of the fixture ground wire directly to the ground wire of the
building system with appropriately sized twist-on connectors – see Drawing
2.
Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to
power supply ground with an appropriately sized twist-on connector inside
post. Cover the open end of the connector with silicone sealant to form a
watertight seal – see Drawing 3.
IS200 Caulking Instructions
- After securing fixture to the wall it is recommended that the gap between the wall and the fixture backplate be sealed on the top and both sides, with a good quality waterproof caulk or silicone sealant (NOT INCLUDED) – see Drawing 1.
- After securing fixture in place it is recommended that the gap between the mounting top and fixture base be sealed with any good quality waterproof caulk or silicone sealant (not included). It is also recommended that a small bead of caulk or sealant be put under the ball knobs used to mount fixture – see Drawing 2.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>