TARAMPS 400 Amplayer Instruction Manual

TARAMPS 400 Amplayer Instruction Manual

The installation of this product must be made by a qualified professional.

Term of warranty

ARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.

This warranty excludes:

• Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
• Tamper or torn warranty seal;
• Cases in which the product is not used in adequate conditions;
• Defects caused by accessories, modifications or features attached to the product;
• The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
• Warranty card is not properly filled or torn;
• Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
• Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical assistance

For international support, check on our website:
www.taramps.com.br/en/rede-de-assistencias- tecnicasor contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br

Introduction

Read this manual before preparing the product. In case of doubt, contact our technical support: (18) 3266-4050 or www.taramps.com.br.

At the end of its useful life, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling center for proper disposal.

Declaration of Conformity

TARAMPS ELECTRONICS LTDA Alfredo Marcondes – SP Brazil

Hereby, Taramps Electronics Ltda declares that the product AMPLAYER 400 complies with the Directive 2014/30/EU, according with the following harmonized standard:

-EN 50498:2010 Electromagnetic compatibility (EMC) – Product family standard for aftermarket electronic equipment in vehicles

The full text of the EU Declaration of Conformity is available at the following Product Page on Internet.

Safety requirements

To ensure proper use, please read through this manual before using the amplifier. It is specially important that you know the CAUTIONS contained here.

• The installation of this amplifier must be done by a qualified professional.
• Wear safety glasses, insulated gloves and correct tools for installing this product
• Wear safety glasses, insulated gloves and correct tools for installing this product.
• This product is for use with 12V batteries. Always check the voltage before installing.
• Never install the Amplayer in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.
• Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating as indicated here in this manual. Use of improper fuse or circuit breaker could result in overheat, smoke, damage to product, injury or burns.
• Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through car’s body.
• Before making any connection to Am player, disconnect the battery negative terminal.
• When in use, the external surface of the Am player becomes hot. Avoid touching the heat sink area and keep children far from the amplifier.
• This product may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.
• If you want to dispose this product, don’t throw it on domestic waste. It must be collected by an used electronic product disposal service for proper recycling.

Safety

As you read this manual, pay attention to the safety symbols.

CAUTION

This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage.

Package content

• 01 Amplayer
  

• 01 Control long range

• 01 plastic part
  

• 02 removal keys

• 01 Taramps cord
  

Functions

1. Source: ON/OFF/ Volume:
   With the Player turned   off: Short press, turns on the device
   With the player turned on
   Long press: turns off the device
   Short touch: select functions: USB / BLUETOOTH/ FM
   Volume: Increases or decreases the audio volume when turning

2. Track / Tune:
   FM Radio
   Short Touch: Decreases the FM tuning frequency by 0.1MHz
   Long   press: Automatically search for the previous FM station bluetooth
   Short Tap: Rewinds music tracks
   USB
   Short Tap: Go to the beginning of the current song Double click: Rewind music tracks

3. Track / Tune:
   FM radio
   Short Touch: Increases the FM tuning frequency by 0.1MHz
   Long press: Auto search next FM station
   Bluetooth / USB
   Short Tap: Next track

4. Advance folder / 1 :
   FM Radio
   Short Touch: Selects radio from memory position 1
   Long press: Saves the station in position 1
   USB
   Short Touch: Advance folder.

5. Rewind folder / 2:
   FM Radio
   Short Touch: Selects radio from memory position 2
   Long press: Saves the station in position 2
   USB
   Short Touch: Rewind folder
   Memorizing FM stations: To memorize FM stations, just choose the desired station and hold down the key from 1 to 6 of your choice.
   

6. Play / Pause / 3 / Sync:
   FM Radio
   Short   Touch: Selects radio from memory location 3
   Long press: Saves the station in position 3
   Bluetooth / USB
   Short Touch: Play/Pause
   Sync: With the player turned off, if pressed for 10s, it allows registering the long-distance control.

7. Repetition / 4:
   FM Radio 
   Short Touch: Selects radio from memory location 4
   Long press: Saves the station in position 4
   USB
   Short Touch: Repeat track/folder, Random function

8. Mute / 5:
   FM Radio
   Short Touch: Selects radio from memory location 5
   Long press: Saves the station in position 5
   Bluetooth / USB
   Short   Tap: Mute

9. Equalizer / 6:
   FM Radio
   Short Touch: Selects radio from memory location 6
   Long press: Saves the station in position 6
   Bluetooth / USB
   Short Touch: Toggles between set EQs (Pop / Rock / Jazz / Country / Normal)

10. USB:
    Input for Pen Drive and/or USBport to charge electronic devices (eg cell phone).

11. LED Display:
    Shows FM radio frequency, track/folder number, signal source, etc…

Output and power connector

1. FM Antenna: Input to connect the FM antenna.

2. Connector   for speakers: To connect the speakers.
   See connection diagram on page 08.
   For connections in STEREO mode, the minimum impedance is 2 ohms in each channel; in BRIDGE mode, it is 4 ohms.
   For loudspeaker associations, the impedance to be considered is the resultant impedance.

3. Power Connector: The (+) wires of the connector must be connected to the positive pole of the battery through a cable with a minimum gauge of 4mm². The wires (-) of the connector must be properly connected to the negative pole of the battery using a cable with the same gauge as the positive cable. See connection diagram on page 07.
   CAUTION
   Before making any connections to the power terminals, make sure that the (-) negative of the vehicle’s battery is disconnected.
   *It is necessary to join the 2 yellow wires (Batt+) and join the 2 black wires (GND)
   Do not use the vehicle’s original wiring. Make a new installation directly from the battery.
   It is recommended to use a 30A fuse or circuit breaker near the battery

4. Low-power mode protection fuse: It has 2 protection fuses, the external 15A (low-power mode) and the internal 30A (high-power mode).

5 e 6- Crossover Front and Rear

SELECTOR IN POSITION – FULL
Amplifies the entire audio range, responding from 10Hz to 20KHz. We normally use this function when we have an external crossover in the system.

SELECTOR IN POSITION – HPF – (HIGH PASS)
It amplifies signals from 90Hz, this type of function is used for reproduction in medium bass and medium speakers, a great example are the two-way kits and 6×9 speakers.

SELECTOR IN POSITION – LPF – (LOW PASS)
It amplifies only the sub bass and bass, as the response is limited to 90Hz (-12dB/8th), ideal cutoff for subwoofers.

LINE OUT: The LINE OUT output allows you to send the audio signal (not amplified) to other equipment, such as an amplifier or active subwoofer.

Panel installation

Position the removal keys as shown in the image below to remove the plastic strap from the product.
ATTENTION: The front of the Amplayer is not removable.

Install the plastic strap in the space intended for installing the radio on the vehicle’s dashboard.
Amplayer may not be compatible with other plastic or metal straps. Use the strap provided for correct locking on the panel.

Having completed the steps above, it is now time to install Amplayer on your vehicle.
See on the next page, the correct way for installation.

Amplayer cleaning

Cleaning the AMPLAYER panel can be done with a soft cloth, to avoid scratches, stains or damage to it.
NEVER use chemical, abrasive or cleaning products.

Installation

CAUTION

CAUTION: All connections to power supply, input and output connectors must be carried out only with amplifier off.

Recommended wire gauge & fuse

Positive / negative power supply cable ____ 4mm²
ACCcable____0.75mm²
Cable P. Antenna / Remote____0.75mm²
Fuse or circuit breaker protection____20A

Calculated considering a maximum length of 4m. Distance greater than this, you will need to increase the cable gauges.

CAUTION

Before making any connections to the power terminals, make sure that the (-) negative of the vehicle’s battery is disconnected.
*It is necessary to join the 2 yellow wires (Batt+) and join the 2 black wires (GND).
Do not use the vehicle’s original wiring. Make a new installation directly from the battery.
It is essential to use a 20A fuse or circuit breaker near the battery.
The use of wiring with a smaller gauge than recommended causes loss of power and overheating of the wiring.
Observe the polarity, never reverse the power cables, under risk of damage to the Player.

**** The installation of this product must be carried out by a qualified professional.

Example of stereo connection 2 Ohms per channel

Bridge connection example 4 Ohms per channel

IMPORTANT: Unused wires must be insulated.

Bluetooth

When selecting the Bluetooth function (identied with “bt”on the display), the Player waits for a Bluetooth connection. Search through your cell phone and make the pairing.
– To connect to a new device, disconnect the current one and re-pair Bluetooth.
Bluetooth specication: class II with an average range of up to 10m.

For other devices, the connection system is similar (see manufacturer’s manual).

Registering another rang distance control

It is possible to use up to 3 controllers simultaneously.
To sync a new remote, follow the instructions:

1. Make sure the AMPLAYER is turned off, however the ACC must be energized.
2. Press and hold the 3/SYNC key for 10 seconds.
3. The panel LEDs will start flashing.
4. On the long-distance control, press the and synchronization keys simultaneously until the LEDs turn off (check if the long-distance control is compatible*).

• The AMPLAYER only works with TARAMPS long-distance control operating at a frequency of 433.5MHz, FSK modulation with its own encryption.

Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.

+55 18 3266-4050

Fabricado por / Manufactured b y: TARAMPS ELECTRONICS LTD A CNPJ / TAX ID: 11.273.485/0001-03 R. João Silvério, 121 • Res. Manoel Martins Alfredo Marcondes – SP Indústria Brasileira – Made in Brazil.
www.taramps.com.br

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>