TARAMPS AMPLAYER 400W Media Player Amplifier Instruction Manual
- June 13, 2024
- TARAMPS
Table of Contents
TARAMPS AMPLAYER 400W Media Player Amplifier
Product Information
The Taramps AMPLAYER 400 is an aftermarket electronic amplifier designed for use in vehicles. It complies with the Directive 2014/30/EU and meets the safety requirements. The product is manufactured by Taramps Electronics Ltda, located in Alfredo Marcondes, SP, Brazil. The amplifier features FM radio, Bluetooth connectivity, and a crossover for adjusting audio frequencies. It has multiple inputs and outputs for connecting speakers, subwoofers, and other audio devices.
Product Usage Instructions
- Before using the amplifier, read the entire user manual to familiarize yourself with its features and functions.
- Ensure that the amplifier is properly installed in your vehicle according to the provided wiring diagram.
- Connect the FM antenna to the designated input on the amplifier for FM radio reception.
- To play music from your device via Bluetooth, pair your device with the amplifier by following the instructions in your device’s Bluetooth settings.
- Use the “Track/Tune” buttons to navigate through FM radio stations and music tracks. Short touch moves to the next track/station, while long touch rewinds within the current track/station.
- For adjusting audio frequencies, use the “Crossover” controls. The crossover frequency range is from 10Hz to 90Hz for front and rear channels.
- Clean the amplifier using a soft cloth. Avoid using solvents or abrasive materials that may damage the surface.
- Refer to the technical support contact information provided in the manual if you have any questions or need assistance with the product.
Please note that proper use of the amplifier is essential for optimal performance and safety. Always follow the instructions provided in the user manual and adhere to the safety cautions mentioned.
Term of warranty
- TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.
This warranty excludes
- Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
- Tamper or torn warranty seal;
- Cases in which the product is not used in adequate conditions;
- Defects caused by accessories, modifications or features attached to the product;
- The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
- Warranty card is not properly filled or torn;
- Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
- Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.
Technical assistance
For international support, check on our website
www.taramps.com.br/en/rede-de-assistencias-
tecnicas or
contact direct the factory support
- Phones: +55 18 3266-4050 / +55 18 99749-3391
- E-mail: service@taramps.com.br
Introduction
Read this manual before preparing the product. In case of doubt, contact our technical
- support: (18) 3266-4050 or www.taramps.com.br.
At the end of its useful life, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling center for proper disposal.
Declaration of Conformity
TARAMPS ELECTRONICS LTDA Alfredo Marcondes – SP Brazil Hereby, Taramps
Electronics Ltda declares that the product AMPLAYER 400 complies with the
Directive 2014/30/EU, according with the following harmonized standard
- EN 50498:2 010 Electromagnetic compatibility (EMC)
- Product family standard for aftermarket electronic equipment in vehicles
The full text of the EU Declaration of Conformity is available at the following Product Page on Internet.
Safety requirements
To ensure proper use, please read through this manual before using the
amplifier. It is specially important that you know the CAUTIONS contained
here.
- The installation of this amplifier must be done by a qualified professional.
- Wear safety glasses, insulated gloves and correct tools for installing this product.
- This product is for use with 12V batteries. Always check the voltage before installing.
- Never install the Amplayer in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.
- Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating as indicated here in this manual. Use of improper fuse or circuit breaker could result in overheat, smoke, damage to product, injury or burns.
- Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through car’s body.
- Before making any connection to Amplayer, disconnect the battery negative terminal.
- When in use, the external surface of the Amplayer becomes hot. Avoid touching the heatsink area and keep childrens far from the amplifier.
- This product may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.
- If you want to dispose this product, don’t throw it on domestic waste. It must be collected by an used electronic product disposal service for proper recycling.
Safety
As you read this manual, pay attention to the safety symbols.
CAUTION
This symbol with “CAUTION” is intended to alert the user to the presence of
important instructions. Failure to heed the instructions will result in risk
of injury to user or product damage.
Package content
Panel / Control Functions Source: ON/OFF / Volume / Mode
- With the Player turned off : Short press, turns on the device With the player turned on
- Short press : select functions: USB / BLUETOOTH / FM
- Long press : turns off the device
- Volume : Increases or decreases the audio volume when turning
Track / Tune
FM Radio
- Short press : Decreases the FM tuning frequency by 0.1MHz
- Long press: Automatically search for the previous FM station bluetooth
- Short press : Rewinds music tracks
USB
- Short press : Go to the beginning of the current song
- Long press : Rewind within the track (Fast Rewind)
- Double click: Rewind music tracks
Track / Tune
- FM radio
Short Touch : Increases the FM tuning frequency by 0.1MHz
- Long press: Auto search next FM station
Bluetooth / USB
- Short press : Next track
- Long press: Forwards within the track (Fast Forward)
Advance folder / 1 : FM Radio
- Short press : Selects radio from memory position 1
- Long press : Saves the station in position 1
USB
- Short press: Advance folder.
Rewind folder
FM Radio
- Short press : Selects radio from memory position 2
- Long press : Saves the station in position 2
USB
- Short press : Rewind folder
-
Short press with the device turned on: Selects the function
- Long press : Turn on and off
- Volume +: Increases the volume
- Volume -: Decreases the volume
-
Track / Tune
-
Track / Tune
-
Avança pasta
- Short press: Advance folder
- Long press: Advances tracks within the folder
-
Retrocede past a : Short press: Rewind folder
- Long press: Rewinds tracks within the folder
- Memorizing FM stations: To memorize FM stations, just choose the desired station and hold down the key from 1 to 6 of your choice. Err: It means there is no station saved in this memory.
Panel / Control Functions
-
Play / Pause / 3 / Sync
FM Radio- Short press : Selects radio from memory location 3
- Long press : Saves the station in position 3
- Bluetooth / USB
- Short press : Play/Pause
- Sync : With the player turned off, if pressed for 10s, it allows registering the long-distance control .
-
Repetition
FM Radio- Short press : Selects radio from memory location 4
- Long press : Saves the station in position 4
USB
Short press: One / random / folder / all
-
Mute
FM Radio- Short press : Selects radio from memory location 5
- Long press : Saves the station in position 5
- Bluetooth / USB
- Short press : Mute
-
Equalizer
FM Radio-
Short press: Selects radio from memory location 6
-
Long press : Saves the station in position 6
Bluetooth / USB -
Short press : Toggles between set EQs (Pop / Rock / Jazz / Country / Normal)
-
-
USB
- Input for Pen Drive and/or USB port to charge electronic devices (eg cell phone).
- The charging type is Stardand mode (max. 1A) and need more time to complete a full charging compared to fast charging modes. If appears the message “PC” into AMPLAYER’s display, just turn left the volume knob.
-
LED Display
Shows FM radio frequency, track/folder number, signal source, etc…
Output and power connector
-
FM Antenna : Input to connect the FM antenna.
-
Connector for speakers: To connect the speakers.
For connections in STEREO mode, the minimum impedance is 2 ohms in each channel; in BRIDGE mode, it is 4 ohms.
For loudspeaker associations, the impedance to be considered is the resultant impedance. -
Power Connector: The (+) wires of the connector must be connected to the positive pole of the battery through a cable with a minimum gauge of 4mm². The wires (-) of the connector must be properly connected to the negative pole of the battery using a cable with the same gauge as the positive cable. See connection diagram on page 17.
CAUTION
Before making any connections to the power terminals, make sure that the (-) negative of the vehicle’s battery is disconnected.
*It is necessary to join the 2 yellow wires (Batt+) and join the 2 black wires (GND).
Do not use the vehicle’s original wiring. Make a new installation directly from the battery. It is recommended to use a 20A fuse or circuit breaker near the battery. -
Low-power mode protection fuse: It has 2 protection fuses, the external 15A (low-power mode) and the internal 20A (high-power mode).
-
Crossover Front and Rear
Audio track SELECTOR IN POSITION – FULL
Amplifies the entire audio range, responding from 10Hz to 20KHz. We normally
use this function when we have an external crossover in the 10Hz 20KHz system.
SELECTOR IN POSITION – HPF – (HIGH PASS)
It amplifies signals from 90Hz, this type of function is used for reproduction
in medium bass and medium speakers, a great example are the two-way kits and
6×9 speakers.
SELECTOR IN POSITION – LPF – (LOW PASS)
It amplifies only the sub bass and bass, as the response is limited to 90Hz
(-12dB/8th), ideal cutoff for subwoofers.
LINE OUT: The LINE OUT output allows you to send the audio signal (not amplified) to other equipment, such as an amplifier or active subwoofer.
If you use this output to send signal to external amplifiers, an adjustment (decrease) of amplifier’s input gain is recommended.
Panel installation
Position the removal keys as shown in the image below to remove the plastic
strap from the product.
ATTENTION: The front of the Amplayer is not removable.
- Install the plastic strap in the space intended for installing the radio on the vehicle’s dashboard.
- Amplayer may not be compatible with other plastic or metal straps. Use the strap provided for correct locking on the panel.
- Having completed the steps above, it is now time to install Amplayer on your vehicle.
- See on the next page, the correct way for installation.
Amplayer cleaning
- Cleaning the AMPLAYER panel can be done with a soft cloth, to avoid scratches, stains or damage to it.
- NEVER use chemical, abrasive or cleaning products.
Installation
CAUTION
CAUTION: All connections to power supply, input and output connectors
must be carried out only with amplifier off.
- Recommended wire gauge & fuse
- Positive / negative power supply cable ___ 4mm² ACC
- cable___0.75mm² Cable P. Antenna /
- Remote__0.75mm² Fuse or circuit breaker protection_____20A
- Calculated considering a maximum length of 4m. Distance greater than this, you will need to increase the cable gauges.
CAUTION
Before making any connections to the power terminals, make sure that the (-)
negative of the vehicle’s battery is disconnected.
- It is necessary to join the 2 yellow wires (Batt+) and join the 2 black wires (GND).
- Do not use the vehicle’s original wiring. Make a new installation directly from the battery.
- It is essential to use a 20A fuse or circuit breaker near the battery.
- The use of wiring with a smaller gauge than recommended causes loss of power and overheating of the wiring.
- Observe the polarity, never reverse the power cables, under risk of damage to the Player.
The installation of this product must be carried out by a qualified professional.
Example of stereo connection 2 Ohms per channel
Bridge connection example 4 Ohms per channel
IMPORTANT: Unused wires must be insulated.
Bluetooth
When selecting the Bluetooth function (identi ed with “bt” on the display),
the Player waits for a Bluetooth connection. Search through your cell phone
and make the pairing.
- To connect to a new device, disconnect the current one and re-pair Bluetooth.
- Bluetooth speci cation: class II with an average range of up to 10m.
Registering another rang distance control
It is possible to use up to 3 controllers simultaneously. To sync a new
remote, follow the instructions
- Make sure the AMPLAYER is turned off, however the ACC must be energized.
- Press and hold the 3/SYNC key for 10 seconds.
- The panel LEDs will start flashing.
- On the long-distance control, press the synchronization keys simultaneously until the LEDs turn off (check if the long-distance control is compatible*).
-
- The AMPLAYER only works with TARAMPS long-distance control operating at a frequency of 433.5MHz, FSK modulation with its own encryption.
Technical features
Number of Channels
HIGH POWER MODE
- Output Power @ 14.4VDC – 2 OHMS: 400W RMS (4 x 100W RMS)
- Output Power @ 14.4VDC – 4 OHMS: * 272W RMS (4 x 68W RMS)
- 2 Bridged Channels @ 14.4VDC – 4 OHMS: 400W RMS (2 x 200W RMS)
LOW POWER MODE
- Output Power @ 14.4VDC – 2 OHMS : 160W RMS (4 x 40W RMS)
- Output Power @ 14.4VDC – 4 OHMS : 100W RMS (4 x 25W RMS)
- 2 Bridged Channels @ 14.4VDC – 4 OHMS : * 160W RMS (2 × 80W RMS)
*Rated power at 14.4VDC, 1KHz sinusoidal signal and THD < 10%. **Frequency response measured at 2 times the minimum impedance, in 4 channel mode. The values as above are typical and may vary, due to electronic components tolerance or manufacturing process.
Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.
Fabricado por / Manufactured by
TARAMPS ELECTRONICS LTDA
- CNPJ / TAX ID : 11.273.485/0001-03
- R. João Silvério, 121
- Res. Manoel Martins Alfredo Marcondes – SP
- Indústria Brasileira – Made in Brazil
- www.taramps.com.br
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>