perle IRG5410 Router User Guide

: June 13, 2024
: perle

Table of Contents

perle IRG5410 Router
What’s in the box?

perle IRG5410 Router

Product Information

The IRG5410 Series Router is a versatile networking device designed for installation and configuration in various settings. This quick start guide provides basic instructions for first-time setup or product evaluation. The models covered by this guide are the IRG5410 and IRG5410+.

For complete details and additional guides, please visit the
Perle website.

What’s in the box?

IRG5410 Series Router Quick Start Guide 5500448-10 (Rev C)
1 x Router

Note: The components included with your product may vary depending on the model. For updates, please refer to the Perle website.

Product Usage Instructions

Inserting the SIM cards

Use only mini-SIM (2FF) cards.
Ensure the power is disconnected before you insert the SIM card/s.
Unscrew the screws and gently pry the SIM cover loose from the opening.
Align the SIM card so that it slides into the top slot (slot#1), with the SIM card connectors facing the router’s printed circuit board. Always populate slot#1 first.
Align the SIM cover plate and secure it with the screws.

Connecting the Antennas

Connect your cellular antenna to the “Main” connector.
Connect the diversity antenna to the “Diversity” connector.
Connect your GPS antenna to the “GNSS” connector.

Connecting the Power

Refer to Figure 2 in the user manual for wiring requirements.
The colors indicated are for the Perle-supplied DC cable.

Connecting to the Cellular Network
When the router is powered on, it will begin the activation process and attempt to connect to the cellular network. This process usually takes a few minutes. A solid green Internet LED indicates a successful connection. If not, refer to the IRG5410
Series Routers Hardware Installation Guide for further details.

Fast Setup Mode

Fast Setup Mode provides a simple method for doing an initial setup from a PC. The router is shipped in factory default mode.

Ensure your PC is set to obtain an IP address automatically using DHCP.
Plug the PC into your router’s Ethernet interface.
When the Power LED is flashing green, open a web browser and enter http://192.168.0.1 to access your router.
On the setup screen, select “Get Started”.
If you select “Get Started”, fill in the required fields, apply the changes, then save and exit. The configuration changes will be immediately applied to the router. You can now access your router’s complete configuration using your supplied credentials from the WebManager.
If you select “See Options”, an alternative screen will appear.
Enabling router configuration via DHCP/BOOTP (ZTP) and rebooting will cause the router to reboot, attempting to download either a new version of firmware and/or a new configuration from a DHCP/BOOTP server.

For alternative initial setup methods, please consult the IRG5410 Router Hardware Installation Guide.

This guide covers basic installation and configuration and is intended for first-time setup or product evaluation. The models covered by this guide are the IRG5410 and IRG5410+.

Complete details can be found in the following guides at www.perle.com/downloads.

IRG5410 Series Router Hardware Installation Guide
IRG5000 Series Router User’s Guide
IRG5000 Series Routers Command Line Reference Guide

What’s in the box?

IRG5410/5410+ Router
IRG5410 Series Routers Quick Start Guide (this guide)
GPIO Cable with 4-pin plug (#2500468)
GPIO Cable with 8-pin plug (#2500476)
12VDC/2A power supply 4 pin (NA #08000150),EU#08000160, UK #08000170)
2 LTE antennas (#08000120)
Optional – GNSS PASV RP-Antenna SMA/CA(#08000130) passive or active antenna
Optional – DIN Rail mounting kit (orderable from Perle)

Note: these components may be included with your product. Components may vary depending on each model. See the Perle website for updates.

Getting Started

The steps for a typical installation are:

Inserting the SIM card/s.
Connecting the antenna/s.
Connecting the Power.
Connecting to the Cellular Network.
Fast Setup Mode.

Inserting the SIM cards

Use only mini-SIM (2FF) cards.
Ensure the power is disconnected before you insert the SIM card/s.

Unscrew the screws and gently pry the SIM cover loose from the opening (see below).
Align the SIM card so that the SIM card will slide into the top slot (slot#1), ensuring that the SIM card connectors will be facing the router’s printed circuit board. Always populate slot#1 first.
Align the SIM cover plate and secure the plate with the screws.

Connecting the Antennas

Connect your cellular antenna to the connector Main.
Connect the diversity antenna to the connector Diversity.
Connect your GPS antenna to the GNSS connector.
See Figure 2
Connecting the Power
See Figure 2 for wiring requirements. The colours indicated are for the Perle- supplied DC cable.

Connecting to the Cellular Network

When the router is powered on, it begins the activation process and attempts to connect to the cellular network. This process typically takes a few minutes. A successful connection is indicated by a solid green Internet LED; if not, see the IRG5410 Series Routers Hardware Installation Guide for details.

perle-IRG5410-Router-2

Fast Setup Mode

Fast Setup provides a simple method for doing an initial setup from a PC. Your router is shipped in factory default mode.

Your PC must be set to obtain an IP address automatically using DHCP.
Plug the PC into your router’s Ethernet interface.
When the Power LED is flashing green, use a web browser, enter http://192.168.0.1 to access your router.
On the setup screen, select, Get Started.
If you select Get Started, fill in the required fields, apply the changes, then save and exit. The configuration changes will be immediately applied to the router. You can now access your router’s complete configuration using your supplied credentials from the WebManager.
If you select See Options, the following screen appears.
Enabling router configuration via DHCP/BOOTP (ZTP) and reboot will cause the router to reboot, and it will attempt to download either a new version of firmware and/or a new configuration from a DHCP/BOOTP server.
For alternative initial setup methods, see the IRG5410 Router
Hardware Installation Guide.