TARAMPS SMART8 8000 Car Audio Amplifier Instruction Manual

: June 13, 2024
: TARAMPS

Table of Contents

TARAMPS SMART8 8000 Car Audio Amplifier
Product Information
Product Specifications
Product Usage Instruction
Introduction
Safety requirements
Functions
Power supply connector
LEDS indicators
Installation
Technical features
Term of warranty
Technical assistance
Smart Line Presentation
Declaration of Conformity
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TARAMPS SMART8 8000 Car Audio Amplifier

Product Information

Product Name: TARAMPS ELECTRONICS LTDA
Product Model: Unknown
Product Family: Standard for aftermarket electronic equipment in vehicles
Manufacturer: TARAMPS ELECTRONICS LTDA
Location: Alfredo Marcondes, SP, Brasil

Product Specifications

Number of Channels: 4
Impedance: 4 OHMS (x4), 1 OHM, 3 OHMS (x4), 4 OHMS (x6), 1.33 OHMS, 1.5 OHMS, 2 OHMS (x2)
Power Output: 8000W RMS
Power Input: 12V DC
Sensitivity: 0.22V ~ 4V
Frequency Response: 10Hz ~ 5KHz (-3dB)
Bass Boost Frequency: 35Hz ~ 55Hz
Bass Boost Level: 0 ~ +10dB

Physical Dimensions and Weight

Dimensions: 228mm x 70mm x 513mm
Weight: 6.60kg

Product Usage Instruction

Before using the product, make sure to read and understand the entire user manual.
Ensure that the negative (-) terminal of the power input is properly connected to the vehicle’s ground (GND).
Connect the RCA cables from the Taramps amplifier to your CD/DVD player or other audio source.
Use the gain control to adjust the amplifier’s input sensitivity according to your audio source.
Set the high pass and low pass frequency using the crossover controls to limit the frequency range of the output signal.
Use the bass boost control to increase or decrease the bass level of the output signal.
Connect the speakers to the amplifier’s speaker outputs.
If using multiple amplifiers, follow the manufacturer’s instructions for proper wiring and configuration.
Ensure that the power supply meets the required specifications (12V DC).
Monitor the amplifier’s power consumption to prevent the excessive drain on the vehicle’s battery.

Introduction

Read this manual before preparing the product. In case of doubt, contact our technical support: (18) 3266-4050 or www.taramps.com.br. At the end of its useful life, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling center for proper disposal.

Safety requirements

To ensure proper use, please read through this manual before using the amplifier. It is especially important that you know the CAUTIONS contained here.

The installation of this amplifier must be done by a qualified professional.
Wear safety glasses, insulated gloves, and correct tools for installing this product.
This amplifier is for use with 12V batteries. Always check the voltage before installing.
This amplifier must be installed in a firm place with at least 1” space around the heatsink for proper heat spreading.
Never install the amplifier in places exposed to dust, humidity, and water. Pay attention to installing it far from the fuel tank, fuel lines, heat sources, and other parts of the vehicle.
Be sure to install a protection fuse or a circuit breaker near the battery. Follow the ampere rating as indicated here in this manual. Use of an improper fuse or circuit breaker could result in overheating, smoke, damage to the product, injury, or burns.
Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through the car’s body.
Before making any connection to the amplifier, disconnect the battery negative terminal.
When in use, the external surface of may amplifier becomes hot. Avoid touching the heatsink area and keep children far from the amplifier.
This amplifier may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.
Output connections for speakers may have voltage levels when the amplifier is operating.
Make sure that the amplifier is turned OFF before proceeding with any connection or disconnection in these terminals.
If you want to dispose of this amplifier, don’t throw it on domestic waste. It must be collected by a used electronic product disposal service for proper recycling.

Safety
As you read this manual, pay attention to the safety symbols.

CAUTION
This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage. Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.

Functions

Functions, inputs & outputs

IN: Input of signal to be amplified. Connect the to the RCA output of the Head Unit using well shielded cable to avoid noise interference.
OUT: Audio signal output. Sends the same input (IN) signal to another amplifier, allowing cascading.
GAIN: Adjusts the input sensitivity of the amplifier, allowing a perfect adjustment to the output signal levels of various head unit models on the market. It is possible to adjust from 4V (minimum sensitivity) to 0.2V (maximum sensitivity).
CROSSOVER
- HIGH PASS FILTER (HPF): Variable setting from 10Hz to 90Hz, which determines the start of the amplifier’s operating frequency.
- LOW PASS FILTER (LPF): Variable setting from 90Hz to 5KHz, which determines the end of the amplifier’s operating frequency.
BASS BOOST
- FREQ: Set the frequency of bass boost from 35Hz to 55Hz.
- BOOST: Set the boost level from 0 to + 10dB at the frequency set in FREQ.
MONITOR LEVEL REMOTE: Connection to an accessory, whose function is to control the gain and monitor the amplifier where all information from the indicator LEDs, such as distortion (CLIP/TEMP) and protection actuation (PROT), will be displayed simultaneously. (Accessory not included).
TERMINAL REMOTE: It must be connected to the remote output of the head unit using an 18 AWG cable.
SPEAKER:
- SPEAKER: Output (positive and negative) for connecting transducers (speakers). Follow the indicated polarity. For speaker associations, the impedance to consider is the resulting impedance:

CAUTION: Due to the presence of voltage at the output terminals when the product is turned on, avoid contact with them. Risk of electric shock.

Power supply connector

SMART COOLER: This amplifier has four internal ventilation fans. For perfect functioning, the amplifier must be installed in a cool and aired place with at least 1” (25mm) space around the heatsink for proper heat spreading. The usual working temperature of the amplifier is 70°C (158°F).
- CAUTION: The fan and ventilation openings are responsible for cooling the amplifier when it is in use, so it cannot be obstructed.
POSITIVE POWER SUPPLY: Use 2/0 AWG cables directly from the positive battery terminal, with a fuse or circuit breaker (230A), as close to it as possible.
NEGATIVE POWER SUPPLY: Use 2/0 AWG cables as short as possible, connected to the negative battery pole. In order for your amplifier to have the best performance, it is necessary to use all the power inputs. See the example on the next page. We recommend that all cables have tinned ends for better electrical contact. In case of power bus bar use, avoid tightening with extenders on the Allen wrench, as excessive torque may break the terminal.
- CAUTION: Before making any connections to the power terminals, make sure that the negative (-) of the vehicle battery is disconnected.

LEDS indicators

LEDS indicators & protection systems

Blue LED steady on: Indicates that the amplifier is turned on.
Flashing yellow LED: Excessive temperature (May be caused by obstruction of the internal fans, improper installation, or poorly ventilated location). When the amplifier reaches the temperature of approximately 90°C (194°F), the thermal protection starts working, the audio is interrupted and the yellow LED will start flashing. The fans will be functioning, in order to cool down the components quickly. Only when the amplifier reaches a safe temperature level, the audio is released and the amplifier gets back to its normal functioning. We recommend don’t turn off the amplifier, so that the cooling time will be shorter, through the ventilation of fans.
Blinking yellow LED according to music: Indicates that the amplifier is operating at the threshold of distortion. If the red LED also blinks, it indicates excessive distortion.
Red LED steady on Short-circuit or impedance lower than that supported at the output.
RED LED flashes 2x: Supply voltage less than 9.5V.
RED LED flashes 3x: Power supply voltage greater than 17V.

Installation

CAUTION: All connections to power supply, input and output connectors must be carried out only with amplifier off.

Recommended wire gauge & fuse

Positive / negative power supply cable _____2 x 2/0 AWG
Output cables wire gauge____7 AWG
Remote cable ____ 18 AWG
Protection fuse or circuit breaker____400A

Calculated considering a maximum length of 4m. Distance greater than this, you will need to increase the cable gauges.

CAUTION: Using wire gauges below the recommendation will result in power loss and overheating of wiring. Check polarity and never reverse power supply cables due to the risk of damage to the amplifier. It is compulsory to install a protection fuses or circuit breakers as close as possible from batteries.

Examples of connections in the power supply input.
Note: Required battery bank capacity: At least 400Ah

Technical features

*Rated power with 60Hz sinusoidal signal, THD <= 1%, with resistive loads, measured with SMD/AD-1 audio power analyzer and Audio Precision APX525 and the product at lower than 50°C (122ºF) case temperature and 12.6V supply voltage. The values as above are typical and may vary, due to electronic components tolerance or manufacturing process. For further information or questions, visit our website or contact TARAMPS ELECTRONICS support.

Term of warranty

TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of a defect during the warranty period, TARAMPS’ responsibility is limited to the repairing or substitution of the device of its own making.

This warranty excludes:

Damaged products by improper installation, water infiltration, and violation by unauthorized individuals;
Tamper or torn warranty seal;
Cases in which the product is not used in adequate conditions;
Defects caused by accessories, modifications, or features attached to the product;
The product with damage from falling, bumps, or nature-related problems (flooding, lightning, etc.);
Warranty card is not properly filled or torn;
Costs involving uninstallation, reinstallation of equipment as well and shipment to the factory;
Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical assistance

For international support, check on our website:
www.taramps.com.br/en/rede-de-assistencias-tecnicas.
or contact the factory support directly:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: angelo.assistencia@taramps.com.br.

Smart Line Presentation

Multi-impedance: Featuring new control technology and new functions, the SMART 8 brings 8000W
RMS rated power in the range of 1 to 2 Ohms: (1 – 1.33 – 1.5 – 1.67 and 2 Ohms with same power);
LEDS: LEDs output signal level indicator on top of product;
RCA input for up to 4V RMS: Input gain adjustment that allows head units up to 4V RMS output level;
Dual RCA IN / OUT Input: RCA connector with input and output function, eliminates the need of “Y” cables to send the same input signal to another amplifier;
Power connector for cables up to 2/0 AWG: Allows the use of power cables with larger gauge (up to 70mm²) for higher performance;
AUTO-Restart Protections: The amplifier automatically restarts after a protection event;
RAMP audio initialization: After turning on the amplifier, audio is released gradually (ramp).

Declaration of Conformity

TARAMPS ELECTRONICS LTDA Alfredo Marcondes – SP Brazil
Hereby, Taramps Electronics Ltda declares that the product SMART 8 complies with Directive 2014/30/EU, according to the following harmonized standard: EN 50498:2010 Electromagnetic compatibility (EMC) – Product family standard for aftermarket electronic equipment in vehicles The full text of the EU Declaration of Conformity is available at the following Product Page on the Internet.