GOOSKY T8 Lengend S2 Mode 2 Transmitter Instruction Manual

GOOSKY T8 Lengend S2 Mode 2 Transmitter

Thank you for choosing Goosky Technology series products. Before entering the remote control world, you must be told a lot of relevant knowledge and precautions to ensure that you can be more comfortable in the learning process. Before starting the operation, please read this manual carefully. We believe it will be of great help to you. Please keep this manual properly for future reference.

Transmitter description-1

Transmitter description-2

• (Product Model)：T8
• (Diameters)：L153W93H154
• (Radio Frequency)：2.404GHz–2.4475 GHz (Transmit Power)：< 20 dBm
• (Weight)：335g
• (Modulation Mode)：2FSK
• (Spread Spectrum Mode)：s-FHSS
• (Working Voltage)：3.7V
• (Remote Distance)：300m
• (Charge Interface)：TYPE-C
• (Low Voltage Alarm)：3.35V
• (Battery Type)：Lithium Polymer Battery
• (Battery Capacity)2800mAh 3.7V
• (Coach Interface) PPM out pedaling

Transmitter description-3

Push down the battery compartment cover, take out the 18650 lithium battery, and remove the battery protective film;

The protruding end (+) pole and the plane end (-) pole of the battery shall be installed into the battery compartment according to the marked direction in the battery compartment;

Transmitter description-4

Transmitter description-5

Turn on and off the remote control

Turn on and off: press and hold power-1 (A) and power-2 (B) at the same time to turn on the power of the remote control (turn on), or turn off the power of the remote control (turn off);

Introduction to flight control binding

Turn on the GOOSKY T8 transmitter, press the BIND button for 3 times after the helicopter is powered on. The blue light flashes quickly. Keep the transmitter less than one meter away from the flight control. The flight control passes self-detection when the blue light is solid on. Then the binding is done.

Transmitter description-6

Introduction to indicator light

Introduction to indicator light

• battery level 75%-100%
• battery level 75%-100%
• battery level 25%-50%
• battery level 0%-25%

1. When only the red light of the power indicator is always on, it should be charged in time to avoid affecting the use;
2. It is recommended to store 75% of the battery power and replenish the battery power every 3 months to avoid over discharge of lithium battery;

Transmitter description-7

CAUTION

1. Disassemble the left and right assembly seats of the remote control, and unplug the connecting wire plug;
2. The left and right assembly seats are installed interchangeably, and then the assembly seat is assembled on the front shell, and the connecting wire is inserted;
3. Adjust the positions of mode1 and mode2 shift key switches to correspond to the left and right hands of the remote control one by one;
4. After assembly, recalibrate the control stick;

Transmitter description-8

Mode1 and mode2 are interchangeable

CAUTION

1. Disassemble the left and right assembly seats of the remote control, and unplug the connecting wire plug;
2. The left and right assembly seats are installed interchangeably, and then the assembly seat is assembled on the front shell, and the connecting wire is inserted;
3. Adjust the positions of mode1 and mode2 shift key switches to correspond to the left and right hands of the remote control one by one;
4. After assembly, recalibrate the control stick;

Transmitter description-9

Introduction to indicator light

1. The remote control is turned off;
2. Turn the two control sticks to the down splays, as shown in the arrow direction, and turn on the power of the remote control at the same time (turn on);
3. At this time, the remote control makes a (beep) sound and enter into the calibration mode.
4. Turn the left and right control sticks along the red line for two circles at the maximum range, then put the accelerator control stick at the lowest position, and the lifting control stick naturally return to the center.
5. When the remote control makes a (di di) sound, the calibration is successful. Then exit the setting.

References

• Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>