TARAMPS TLC 3000 Function No Cover Long Range Instruction Manual

: June 13, 2024
: TARAMPS

Table of Contents

Term Of Warranty
Technical Assistance
Introduction
Knowing the Transmitter
Knowing The Receiving Base
Getting The Best Performance Out Of The Product
Installations
Setting – Memory Mode
Setting – Learn Mode
Setting – Synchronizing (Up to 3 Controls)
Replacing the Battery
Canceling The Increase Volume Repeat (+)
Memory Mode Chart
Continuation… Memory mode chart
Technical Features
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TARAMPS TLC 3000 Function No Cover Long Range

TARAMPS TLC 3000 Function No Cover Long Range

Term Of Warranty

TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19.180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.

This warranty excludes:

Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
Tamper or torn warranty seal;
Cases in which the product is not used in adequate conditions;
Defects caused by accessories, modifications or features attached to the product;
The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
Warranty card is not properly filled or torn;
Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical Assistance

For international support, check on our website:

www.taramps.com.br/en/rede-de-assistencias- tecnicas or contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br

Congratulations on your purchase of a Ta ramps product.
It was developed in a modern laboratory and with the latest technology.
This manual covers all features, operations and instructions to solve any doubt that may arise during the installation. Please take some time to read it carefully in order to ensure the proper installation and the use of all benefits that this product can offer.
For questions, please call +55 (18) 3266-4050 or visit www.taramps.com.br

Introduction

The REMOTE CONTROL TLC 3000 can be adapted to most Head Units in the market.
A high-tech product that operates on radio frequency (RF), emulating the basic functions of the original infrared control of your device, at long distance.
It has encrypted codes that prevent copy and retransmission of signals.
This transmission is done in FSK (Frequency Shift Keying), thus reducing to the maximum the external interferences.

Knowing the Transmitter

Transmission indicator LED and battery
Increase volume(+)
Decrease volume(-)
Previous track
Next track
Play/ Pause key
Power key and multi functions
Folder up
Folder down
Strap for Cord

Knowing The Receiving Base

Infrared sensor
SYNC/LEARN configuration key
LED signal reception indicator
Antenna
Power input (+12V and GND)
Infrared transmitter

Getting The Best Performance Out Of The Product

In order to obtain the maximum performance of the product (range, ease of configuration and quality), we recommend to observe the following indications carefully:

When fix the Receiver Base, make sure that the antenna is not curled or pointing to another opposite location from which you will most use the Transmitter Control. Always leave it vertically.
Make sure that the infrared transmitter is pointed directly to the CD/ DVD Player of your vehicle.
It is advisable not to fix the Receiver Base in glasses in which they have films, as it may damage them if you need to remove the product from the place. Try to install on insulated surfaces and away from metal plates or other metal surfaces that can absorb or reflect (fading) the RF signals.
Once the installation is performed, when it is necessary to use the control with the need of wide range, it is important that there is a line (without obstacles) between the two products. Walls, trees and metal structures can also attenuate or cause RF signal failure and consequently reduce the range of the device.
Momentary failures may occur if the battery is low. Check the Control if the LED indicator is indicating “low battery”. In this case the Ieds of the receiving base and control will be on for 3 seconds after pressing any key. It is recommended to replace a new CR2032 battery.

Installations

After fix the Receiver Base to a location of your choice, connect the positive(+ 12V) power cables to the positive terminal of the battery and the negative (GND) to the negative terminal of the battery. It is recommended for safety the use of 1 Amp fuse in the positive cable with a maximum distance of 30cm from the battery.
Position the Infrared so that it is toward the panel of your Head Unit.
Ready!
Now, we need to configure your Control so that the receiver sends the signals correctly to your Player.

Note : This product is already set up for the Pioneer CD Player models.

If your Head Unit is of another brand, use the table to configure the MEMORY MODE, because in this mode there are compatibilities with various models of Head Units on the market. See chart on the page 09.
If your device is not listed in the table, you will need to use LEARN MODE, see this explanation on.

Setting – Memory Mode

Setting - Memory Mode

Caution : Do not approximate the Receiver Base closer than 30cm, as it may not work properly due to the high sensitivity of the product.

Configuration complete. Make sure that the product is properly controlling your head Unit.

Note : It is possible to cancel the configuration at any time by pressing the SYNC/LEARN key twice.

Setting – Learn Mode

Setting - Learn Mode

Learn Mode one function: In this case the key will have only one function copied from the original control.
Forth is use the short press (click).
Learn Mode two functions: In this case the key will have two functions copied from the original control, the first function being recorded for short press and the second function for long press.

Setting – Synchronizing (Up to 3 Controls)

The TLC-3000 is already factory-synchronized. If you need to synchronize more controls by losing the original or to have more controls registered on the receiving base, follow the setup procedures below.
$Setting - Synchronizing $Up to 3 Controls$$
$Setting - Synchronizing $Up to 3 Controls$$

Setup finished. Check that the receiver base LED is blinking by pressing the control keys indicating synchronization is ok.

Note:. You can cancel the configuration at any time by pressing the SYNC/LEARN key 3x.

Replacing the Battery

Your control will advise you when you need to replace the battery.
If the indicator LED stays on for 3 seconds after pressing any key, your battery needs to be replaced with a new one.
To replace the battery simply unlock the case of the control with an appropriate tool. Then replace the low battery with a new one in the same position by observing the correct polarity.
Replacing the Battery

Canceling The Increase Volume Repeat (+)

For protection of the sound system, your control has a cancellation of the VOLUME (+) key repeat. In this case, when you press the button, the sound volume will only increase by one level.
Press the ( ) ( ) keys simultaneously to activate this function. The red LED will be on for 2 seconds and will turn off. To return to the function, repeat the operation.

Memory Mode Chart

| Key combination
---|---
Model| 1 a key| 2 a key
Pioneer CD| +| +
Pioneer DVD|

–

|

–

RESET CODE: Clears memory. It can be used optionally before loading the codes by the LEARN process.

Continuation… Memory mode chart

Continuation... Memory Mode Chart

Functions used to change folder in USB flash drive.

Based on chart, choose the model corresponding to your device and press the key combinations. Follow the step-by-step on.

Technical Features

Power Supply
Receiver Base: 6 ~16VDC
Transmitter (Control): 1.8 ~ 3.6V (Battery CR2032 )

Consumption
Receiver Base: 30mA (max.)
Transmitter (Control): 7mA (Battery CR2032)

Modulation: ASK
Frequency: 433.92 MHz
Maximum Power: +10dBm

Dimensions
Receiver Base (W x H x D): 54 x 17 x 46mm / 2.13″ x 0.67″ x 1.81″
Transmitter – Control (LxWxD): 36.5 x 11.5 x 76.5mm / 1.44″ x 0.45″ x 3.01″

Weight
Base Receiver: 0.1Kg / 0.22lb
Transmitter – Control: 0.1Kg / 0.22lb

Before installing your product, check the content inside the package.
1 – Control (Transmitter)
1 – Receiving Base
1 – 4-way cable already connected
1 – Custom Cord Taramps
1 – Protective case (Only for color series) Refer to the purchased product label.

Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.

Customer Support

+5518 3266-4050
Fabricado por / Manufactured by:
TARAMPS ELECTRONICS LTDA
CNPJ / TAX ID: 11.273.485/0001-03
R. João Silvério, 121 • Res. Manoel Martins
Alfredo Marcondes – SP
Indústria Brasileira – Made in Brazil
www.taramps.com.br

Logo