TARAMPS LED 90 Dual Voltage 1200W Switch-Mode Power Supply Instruction Manual
- June 13, 2024
- TARAMPS
Table of Contents
TARAMPS LED 90 Dual Voltage 1200W Switch-Mode Power Supply
Product Information
The LED 90 Power Supply is a high-quality product developed by Taramps Electronics. It has a power output of 1200 Watts and operates at 12 Volts. The power supply is designed with advanced technology and features a digital electronic circuit that controls and stabilizes its output. It is an automatic bivolt switched power supply, which means it can be used with both 127V and 220V power sources. This power supply is suitable for various applications, including powering LED strips, CCTV security cameras, car audio systems, and radio communicators.
Product Usage Instructions
- Before using the LED 90 Power Supply, carefully read the user manual to familiarize yourself with its features and operation.
- Ensure that the power supply is disconnected from the mains before connecting any cables or equipment.
- To connect the LED 90 Power Supply to your battery or 12Volt equipment, follow these steps:
- Identify the DC OUTPUT +V terminal on the power supply.
- Connect the positive (+) cables from your battery or equipment to the DC OUTPUT +V terminal.
- Identify the DC OUTPUT -V terminal on the power supply.
- Connect the negative (-) cables from your battery or equipment to the DC OUTPUT -V terminal.
- For safety reasons, it is recommended to ground the LED 90 Power Supply using the GROUNDING terminal.
- Once all connections are made, you can plug the power supply into the mains. The LED ON indicator will illuminate to indicate that the power supply is connected to the mains.
- If you have any questions or need assistance, you can contact Taramps Electronics through the provided phone numbers, email address, or visit their website for technical support and warranty information.
Please note that Taramps Electronics reserves the right to modify the contents of the user manual without prior notice. Make sure to check for any updates or changes on their website or by contacting their customer support.
The installation of this product must be made by a qualified professional.
Introduction
Congratulations on your purchase of a Taramps product.
It was developed in a modern laboratory and with the latest technology.
This manual covers all features, operations and instructions to solve any
doubt that may arise during the installation. Please take some time to read it
carefully in order to ensure the proper installation and the use ofall
benefits that this product can offer.
For questions, please call +55 (18) 3266-4050, e-mail
support@taramps.com.br or visit
www.taramps.com.br.
Presentation
-
NEVER INVERTTHE POLARITY of batteries that can be connected to the source output.
-
This equipment has an “automatic bivolt” system – it automatically recognizes the voltage of the electrical power AC and adjusts itself to it. For the source to have the expected performance, the socket voltage must be between 90V to 140V (127V power AC) or between 190V to 250V (220V power AC).
-
Install the source in a firm and ventilated place, preferably without sunlight and other sources of heat.
Leave a space of 20 centimeters on the sides, not obstructing the cooler inlets. -
The source does not have internal parts that can be maintained by the user. Do not open it, risk of electric shock.
-
The electrical power AC and the use of extensions must be adequate to support the desired power.
Term of warranty
TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.
This warranty excludes:
- Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
- Tamper or torn warranty seal;
- Cases in which the product is not used in adequate conditions;
- Defects caused by accessories, modifications or features attached to the product;
- The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
- Warranty card is not properly filled or torn;
- Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
- Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.
Technical assistance
For international support, check on our website: www.taramps.com.br/en/rede-
de-assistencias-tecnicas or contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br
Knowing the LED 90 Power Supply
The LED 90 Power Supply is an automatic bivolt switched power supply. It has a digital electronic circuit that controls and stabilizes its output, providing more security when connecting your LED strips, cctv security cameras, car audio, radio communicators, among others.
It has simple installation, not requiring any special connector.
- Maximum input power: 800W (1.5mm? recommended wiring).
- Output power in RMS = 500W continuous.
- Maximum power of Automotive Sound = 1200W RMS (60A Dynamic 4 seconds).
- Protection against output short circuit: Turns off the output if a short is detected or a load far above the permitted value is detected.
- Temperature Protection: Reduces power momentarily, returning automatically with a decrease in temperature.
- Output activation time: 300ms (average).
-
LED ON: It stays on as long as the source / charger is connected to the mains.
-
ADJ/VOLTAGE: Ajust the output voltage from 8V to 14.5V.
For automotive battery recharge, it is recommended to set the output voltage greater than 13.8V. -
DC OUTPUT +V: To connect the positive (+) cables to the battery or 12 Volt equipment.
-
DC OUTPUT -V: To connect the negative (-) cables to the battery or 12 Volt equipment.
-
GROUNDING: To avoid possible electric shock, we recommend grounding the equipment.
-
POWER INPUT: Use a 1.5mm² cable. Power cable not included.
-
COOLING FAN: The cooler remains on according to the power supply status: By current or temperature.
IMPORTANT: Never obstruct the fan and leave a 20cm space on the sides.
- Dimensions (WxHxD): 119x58x157mm (4.69″x2.28″x6.18″)
- Weight: 0.69Kg (1.52lb)
Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.
+55 18 3266-4050
Fabricado por / Manufactured by:
TARAMPS ELECTRONICS LTDA
CNPJ / TAX ID: 11.273.485/0001-03
R. João Silvério, 121 • Res. Manoel Martins
Alfredo Marcondes – SP
Indústria Brasileira – Made in Brazil
www.taramps.com.br
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>