ADI P116D222R5 4 Point PRO Mounting Hardware Owner’s Manual

: June 13, 2024
: ADI

Table of Contents

ADI P116D222R5 4 Point PRO Mounting Hardware
Product Information
Product Usage Instructions
Customer Satisfaction
Important Information
Parts and Accessories
- 4 Point PRO Mounting Hardware Assembly
- 4 Point PRO Torque Speciﬁcation
Installation Instructions
First Time Use
- User Testing
- Conditions of Use
Maintenance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ADI P116D222R5 4 Point PRO Mounting Hardware

Product Information

Product Name| ADI 4-Point PRO Mounting Hardware for Aluminum & Carbon
Series Backs
---|---
Manufacturer| Stealth Products, LLC
Warranty| Covers: 2 Years Hardware: 5 years Electronics: 3 years

Product Usage Instructions

Contact a healthcare professional trained for fitting, application, and installation to install the product. Do not attempt to install the product yourself as it may result in serious injury.
In case of a product failure covered by the warranty, follow these steps:
Call Stealth Products at 512-715-9995 or toll-free at 800-965-9229.
Request a Return Authorization (RA) form from the Returns Department and follow the documentation instructions.
To access additional copies of the user manual, visit the Stealth website at https://stlpro.site/stealth-docs and search for “4 Point PRO” in the search bar at the top of the page.

Customer Satisfaction

Stealth Products is committed to 100% customer satisfaction. Your complete satisfaction is important to us. Please contact us with feedback or suggestions to help us improve the quality and usability of our products.

You may reach us at:

Stealth Products, LLC

104 John Kelly Drive, Burnet, TX 78611
Phone: 512-715-9995
Fax: 512-715-9954
Toll Free: 800-965-9229
Toll Free: 800-806-1225
info@stealthproducts.com
www.stealthproducts.com.

General
Read and understand all instructions prior to the use of the product. Failure to adhere to instructions and warnings in this document may result in property damage, injury, or death. Product misuse or failure to follow instructions will void the warranty.

Immediately discontinue use if any function is compromised, if parts are missing or loose, or if any component shows signs of excessive wear. Consult with your supplier for repair, adjustment, or replacement. All persons responsible for fitting, adjustment, and daily use of the devices discussed in these instructions must be familiar with and understand all safety aspects of the devices mentioned. In order for our products to be used successfully, you must read and understand all instructions and warnings, and maintain our products according to our instructions on care and maintenance. The installation instructions will guide you through this product’s options and possibilities.

Instructions are written with the expressed intent of use with standard conﬁgurations. They also contain important safety and maintenance information, as well as describe possible problems that can arise during use. For further assistance, or more advanced applications, please contact your supplier or Stealth Products at 512-715-9995 or toll-free at 800-965-9229. Always keep the operating instructions in a safe place so they may be referenced as necessary. All information, pictures, illustrations, and speciﬁcations are based on the product information that was available at the time of printing. Pictures and illustrations shown in these instructions are representative examples and are not intended to be exact depictions of the various parts of the product.

Important Information

CAUTION
These products are designed to be ﬁtted, applied, and installed exclusively by a healthcare professional trained for these purposes. The ﬁtting, application, and installation by a non-qualiﬁed individual could result in serious injury.

Warranty

Our products are designed, manufactured, and produced to the highest of standards. If any defect in material or workmanship is found, Stealth Products will repair or replace the product at our discretion. Any implied warranty, including the implied warranties of merchantability and ﬁtness for a particular purpose, shall not extend beyond the duration of this warranty. Stealth Products does not warrant damage due to, but not limited to: misuse, abuse, or misapplication of product, and/or modiﬁcation of product without written approval from Stealth Products, LLC. Any alteration or lack of serial number, where applicable, will automatically void all warranties.

Stealth Products, LLC Is liable for replacement parts only. Stealth Products, LLC is not liable for any incurred labor costs.
Stealth Products warrants against failure due to defective materials or workmanship:
- Covers: 2 years
- Hardware: 5 years
- Electronics: 3 years
In the event of a product failure covered by our warranty, please follow the procedures outlined below:
Call Stealth Products at 512-715-9995 or toll-free at 800-965-9229.
Request a Return Authorization (RA) form from the Returns Department and follow the documentation instructions.
You can download additional copies of this manual by accessing the Stealth website (https://stlpro.site/stealth-docs) and searching “4 Point PRO” in the search bar at the top of the page.

Supplier Reference

Supplier:|
---|---
Telephone:|
Address:|
|
Purchase Date:|
Model:|

Warning Labels

Warnings are included for the safety of the user, client, operator, and property. Please read and understand what the signal words DANGER, WARNING, CAUTION, NOTICE, and SAFETY mean, and how they could aﬀect the user, those around the user, and the property.

DANGER Identifies an imminent situation that, if not avoided, may result in severe injury, death, and property damage.
WARNING Identifies a potential situation that, if not avoided, may result in severe injury, death, and property damage.
CAUTION Identifies a potential situation that, if not avoided, may result in minor to moderate injury and property damage.
NOTICE Identifies important information not related to injury, but possible property damage.
SAFETY Indicates steps or instructions for safe practices, reminders of safe procedures, or important safety equipment that may be necessary.

Limited Liability

Stealth Products, LLC accepts no liability for personal injury or damage to property that may arise from the failure of the user or other persons to follow the recommendations, warnings, and instructions in this manual.
Stealth Products does not hold responsibility for ﬁnal integration of ﬁnal assembly of product to end user. Stealth Products is not liable for user death or injury.

Parts and Accessories

Tools Required for Installation and Adjustment

4mm Allen wrench
10mm wrench

Parts Required

Back Support Shell, 1 each (A)
Bent Bracket Assembly, 2 each, attached to back (B)
Inside Clamp, 4 each (C)
Outside Clamp, 4 each (D)
M6 x 35mm Bolt, 4 each (E)
Nylock Nut, 4 each (F)
M6 Fender Washer, 4 each (G)
M6 ID x 10mm OD x 1mm, 4 each (H)

4 Point PRO Mounting Hardware Assembly

NOTICE
Use only the hardware supplied with the ADI back on the ADI back. Do not substitute any other screws, brackets or clamps. Use of alternate hardware or mounting brackets will void all warranty.

4 Point PRO Torque Speciﬁcation

Part Number M6 X 1.0 X 35MM BHS
M6 x 35mm button head screw
- Use: 4mm drive Allen Wrench
- Torque Specs: 77.0 in-lbs/8.7 N·m
Part Number BR5011
Stud Plate (Inner side of shell)
- Use: 10mm hex socket or wrench
- Torque Specs: 117.0 in-lbs/13.2 N·m

Installation Instructions

Hardware Installation

Remove the existing wheelchair according to the original manufacturer’s instructions.
Visually determine the desired height of the back support.
Mark on the wheelchair back posts the desired location of mounting hardware.
Place one inner clamp (C) and one outer clamp (D) around the back cane on one side of the chair. Fasten with a 35mm bolt (E).
NOTICE
The clamp assembly should be rotated out slightly. Do not tighten completely at this stage.
Repeat step 4 on the other side of the chair.
Hold backrest in place and turn left and right clamp assemblies until the 35mm bolts (E) slide into the top slots on the bent brackets (B).
CAUTION
- ADI backs may not ﬁt every chair. Please consult your clinician or supplier providing your equipment.
- DO NOT attach the ADI back with the user in the chair.
Slide the remaining inner clamps (C) and outer clamps (D) into place with the 35mm bolt (E) running through the bottom slots of the bent bracket. (B).
Fasten the bent brackets (B) onto all four 35mm bolts (E) with a washer (G) and a nylock nut (F).

Angle Adjustment

On each side of the hardware, loosen the top and bottom nuts (F) with a 10mm wrench.
Adjust back support to achieve the desired user angle.
After ﬁnal adjustments are complete, tighten all screws to the proper torque speciﬁcation.

Depth Adjustment

On each side of the hardware, loosen the top and bottom nuts (F) with a 10mm wrench
Slide back support forward or aft to achieve desired user depth.
After ﬁnal adjustments are complete, tighten all screws to the proper torque speciﬁcation.

Width Adjustment

Remove fabric cover from back support.
On each side of the hardware, loosen the top and bottom nuts (as shown), using a 10mm socket or wrench.
Adjust hardware inward or outward to achieve required mounting hardware width.
After ﬁnal adjustments are complete, tighten all screws to the proper torque speciﬁcation.

WARNING
Protect all backs from blunt forces that may cause damage and/or breakage

CAUTION
When positioning an ADI back, the interior portion of the back support should be positioned to make a contact at the PSIS to provide optimal pelvic support and trunk control.

First Time Use

Dealer Assistance
During ﬁrst time use by the client, it is advised that the dealer or service technician assists and explains the set-up to the customer (the user and/or the attendant). If needed, the dealer may make ﬁnal adjustments.

User Testing

It is important that the customer is fully aware of the installation, how to use it, and what can be adjusted in order to gain as much mobility as possible. As a dealer, proceed as follows:

Explain and show the customer how you have executed the installation, and explain the function of the hardware.
If needed, adjust the hardware to the proper position.
Explain to the customer possible problems and how to address them.

CAUTION

If you are able to fold the back canes, the back should be in the folded position when transporting the wheelchair, especially before loading for air travel.
Do not use ADI backs during vehicle transportation.

Conditions of Use

The ADI hardware is intended for use as installed by the dealer, in accordance with the installation instructions in this manual.

The foreseen conditions of use are communicated by the dealer or service technician to the user and/or attendant during the ﬁrst time of use.
If the usage conditions change significantly, please contact your dealer or a qualiﬁed service technician to avoid excessive wear and tear or unintended damage.