RALPH LAUREN IG RL5005CG Ceiling Lighting Instruction Manual
- June 4, 2024
- ralph lauren
Table of Contents
IG RL5005CG Ceiling Lighting
Instruction Manual
IG RL5005CG Ceiling Lighting
ASSEMBLY INSTRUCTIONS
Daniela Medium One-Tier Chandelier
NOTICE:
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction and
operation of it, as well as the hazards involved. Inspect items and contents
carefully. If any damage or defect is found, do not install it.
Retain all packaging material until installation is complete and approved.
-
Carefully remove all parts from the box.
-
A 1/4” threaded nipple must be installed in your outlet box. Then install the threaded nipple (B) into the outlet box.
-
Attach the canopy (D) to the ceiling loop (C) and secure it with a lock collar (E).
-
With the fixture dimension as a guide, shorten the chain (F) as needed using a pair of chain pliers.
-
Unscrew the threaded collar on the chain end link and attach it to the ceiling loop (C). Close the threaded collar to secure it.
-
Unscrew the threaded collar on the other chain end link (G), raise the fixture body, and attach the chain end link to the top ring (H). Close the threaded collar to secure the fixture body.
-
Gently set the wire arm (I) to the center plate (J) and secure using the spring washer & lock nut. Check that the arms are spaced evenly before final tightening.
-
Connect the hot wire (smooth edge, markings) from the arms to the main hot wire (smooth edge, markings) from the center plate (J) using wire nut (L).
-
Connect the neutral wire (ribbed, no markings) from the arms to the main neutral wire (ribbed, no markings) from the center plate (J) using wire nut (L).
-
Wrap all connections individually with electrical tape. Double-check that all of your connections are correct.
-
Attach the metal bowl (M) to the center plate (J) and secure it with a metal tube (N).
-
Attach the plastic washer & crystal bowl (O) & crystal (P) & crystal disk (Q) to the metal tube (N) and secure with a finial (R).
-
Unwrap the wiring from the top of the fixture body. Weave the power supply cord and the ground wire through the chain (F).
-
When you reach the canopy and ceiling loop, measure the wires then cut. Be certain to leave enough to connect inside the outlet box.
-
Strip the insulation back on the two power supply wires about 5/8″.
-
Twist the power supply and ground wire together and push through the center hole of the ceiling loop (C).
-
Loosen the lock collar (E) and let the canopy (D) slip down the chain carefully.
-
Connect the fixture ground (bare) wire with the ground wire from the outlet box using wire nut (A) . If your house does not have ground wire, then attach this wire to the green grounding screw inside of the outlet box.
IT IS IMPERATIVE THAT THIS FIXTURE BE GROUNDED. -
Connect the fixture Neutral (ribbed, no markings) wire with the neutral wire from the outlet box using wire nut (A).
-
Connect the fixture Hot (smooth edge, markings) wire with the hot wire from the outlet box using wire nut (A).
DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED. -
Tuck these wire connections neatly into the outlet box to secure them.
-
Put canopy (D) to the ceiling loop (C) and secure with lock collar (E).
-
Insert bulbs (not included) into the sockets.
-
Attach the crystal drop (A) on the hook (A1).
-
Attach the crystal drops (B) on hook (B1).
-
Attach the crystal drops (C) on hook (C1).
-
Attach the crystal drops (D) on hook (D1).
-
Attach the crystal drops (E) on hook (E1).
-
Attach the crystal drops (F) on the hook (F1).
-
Attach the crystal drops (G) on hook (G1).
-
Attach the crystal drops (H) on the hook (H1).
-
Attach the top hook (I1) of crystal drops (I) on hook (I4).
-
Attach the bottom hook (I2) of crystal drops (I) on hooks (I5 & I6).
-
Attach the crystal drops (J) on hook (J1).
-
Attach the crystal drops (K) on hook (K1).
-
Attach the crystal drops (L) on the hook (L1).
-
Installation is complete, turn on the power at the fuse or circuit breaker.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.