OLIGHT Seeker 3 Pro 4200 Lumens Ultra-Bright LED Flashlight User Manual

OLIGHT Seeker 3 Pro 4200 Lumens Ultra-Bright LED Flashlight User Manual

Thank you for purchasing this Olight Product. Please read this manual carefully before use and keep it for future reference!

IN THE BOX

• **Seeker 3 Pro ( With Battery )

**

• **Holster

**

• **USB Magnetic Charging Cable

**

SPECIFICATIONS

All above specifications are test results based on ANSI/NEMA FL1-2009 Standard. The tests are performed using the battery included in the flashlight.
Note: The maximum output brightness will decrease as the battery voltage decreases.

PRODUCT OVERVIEW

INDICATORS ON BOTH SIDES

NOTE: While turning on, if the battery power is less than 10%, the lowest indicator on the right side will glow red.

AVAILABLE BATTERIES

• 1 x customized 5000mAh 21700 rechargeable lithium battery

BEFORE FIRST USE

Before first use, unscrew the tailcap and remove the insulating film within the battery compartment before screwing the tailcap back on tightly. If the battery needs to be changed, make sure that the negative polarity side of the battery faces toward the direction of the flashlight head ( the side of the LED ).

The flashlight arrives in lockout mode for shipping purposes. To unlock, please rotate the knob switch quickly over 90 degrees. The surrounding indicators will light up when you have unlocked the switch successfully.

USB MAGNETIC CHARGING CABLE — MCC3

is insufficient to provide 5V 2A power capacity, the charging time will be longer)
Charge indication| Red ：charging Green: full (over 95%) or disconnected with flashlight

CHARGING

• Before first use please fully charge the product.
• Connect the magnetic USB end of the charging cable to an external USB power source , then attach the other end of the magnetic charging cable to the charging port(best charging efficiency with more than 10W ( 5V 2A ) USB power source ). The red indicator means charging , green indicator means charging completed (battery power >95%).
• Only charge with standard MCC, not compatible with other MCC.

PROXIMITY PROTECTION FUNCTION

1. When the light is on and set at Level 3 or higher brightness, if the front lens proximity sensor detects an obstruction nearby, the brightness will automatically reduce. While in this state, the stepless dimming by rotating the knob switch is invalid. The brightness will restore the previous brightness when the obstruction is gone.

2. To turn off the proximity sensor, please quickly double click (or triple-click) the knob switch within 5 seconds after dimming the brightness automatically, the light will enter into the corresponding mode. Turn off the light can restart the proximity sensor.

ATTENTION

• The built-in sensor may NOT work if it is blocked by water or dirt on the front lens. Please keep the lens clean to ensure that it works properly.
• Please protect the surface of the front lens carefully. It may reduce the light output if it has scratches on the front lens.

DANGER

• DO NOT shine the light directly into human eyes.
  This may cause temporary blindness or permanent damage to the eyes.

• Keep out of reach of children.

• DO NOT cover the flashlight when it is on. The heat built-up may cause close objects to burn or even result in unexpected disasters.

• DO NOT use the rechargeable battery without battery protection board and broken.

• DO NOT immerse the flashlight in seawater or other corrosive media as it will enter and damage the charging port.

• DO NOT take out or use other chargers to charge the customized battery, it may cause damage.

WARNING

• DO NOT activate high mode repeatedly under high temperature to prevent the flashlight body from overheating and hurting the users’ hands.
• Please keep the charging port clean and dry before charging and maintain it regularly.
• If the battery needs to be changed, please store it carefully away from the conductive metal.
• If the light is about to be put aside for a long time or be transported, please unscrew the tailcap and remove the battery to cut off the circuit.

NOTICE

• The light will dim brightness automatically when it with high temperature to prevent it from overheating and hurting the users’ hands.

EXCLUSION CLAUSE
Olight is not liable for damages or injuries sustained resulting from the usage of the product inconsistent with the warnings in the manual, including but not limited to using the product inconsistent with the recommended lockout mode.

HOW TO OPERATE

LOCKOUT/UNLOCK: The knob switch will be locked\ out automatically, if no operation is made within 30 seconds after the light is off. In the lockout mode, single click the knob switch will not turn on the light and the battery indicator will indicate the battery level. To unlock, please rotate the knob switch over 90 degrees, whereupon indicators around it will be on for 3 seconds.

IN THE UNLOCKED STATE:

ON/OFF: Single click the knob switch to turn the light on/off. When the light is turned on, it will return to the previous brightness level selected before the light was turned off. (The high mode and above brightness will be memorized as high mode, the rest of brightness can be memorized when the light is turned off. The medium mode and above brightness will be memorized as medium mode after one minute when the light is turned off.)

CHANGE BRIGHTNESS LEVEL: When the light is on, press and hold the knob switch and it will, starting from the present brightness level, automatically cycle through Low, Medium, and High mode. The mode is selected when the knob switch has been released. (Please note: moonlight and turbo are not in the automatic cycle.)

MOONLIGHT: When the light is off, press and hold the knob switch for over one second to access the moonlight mode.

TURBO AND RETURN: Quickly double click the knob switch to enter into Turbo, double click again to return. The medium mode and above brightness will be memorized as medium mode.

STROBE: Quickly triple-click the knob switch to activate strobe mode. To quit this mode, single click or press and hold the knob switch

ROTATE CLOCKWISE (STEPLESS INCREASING): When the light is on, rotate the knob switch clockwise to ramp up the brightness level to the highest in permitted conditions. The corresponding brightness level grid of the brightness controller will flash to remind when the brightness reaches its present highest brightness.

ROTATE COUNTERCLOCKWISE (STEPLESS DECREASING)： When the light is on (not in the moonlight mode), rotate the knob switch counterclockwise to decrease the brightness level to the low light mode. The corresponding brightness level grid of the brightness controller will flash to remind when the brightness reaches its present lowest brightness. When the light is turning on in the moonlight mode, rotate the knob switch counterclockwise will not change the mode.

TIMER: The Seeker 3 Pro has a long (9 minutes) and short (3 minutes) timer when the light needs to be automatically turned off. When the light is on, double click and hold the knob switch under the current brightness level to access the timer settings. A single blink accesses the short timer while two blinks accesses the long timer. The light will automatically turn off when the timer is up.

WARRANTY

Within 30 days of purchase: Contact the original seller for repair or replacement.
Within 5 years of purchase: Contact Olight for repair or replacement.
Battery warranty: Olight offers a one year warranty for all rechargeable batteries.
MCC magnetic USB charging cable : One year.

For any of the fragile or low-value fittings not covered above, like lanyard and clip, you can contact the post-sale in 30 days after the purchase, if it has any quality drawback or damage under normal use condition. If such drawback or damage occurs 30 days after the purchase or under abnormal use condition, we will only offer conditional quality assurance as appropriate.

EU-DECLARATION OF CONFORMITY
EU-Declaration of Conformity can be found here: https://olightworld.com/ec- declaration

USA Customer Support
cs@olightstore.com
Global Customer Support
Customer-service@olightworld.com
Visit www.olightworld.com to see our complete product line of portable illumination tools.

Dongguan Olight E-Commerce Technology Co., Ltd
4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.

References

• Olight | Illuminate Your World.
• Flashlights, Tactical Light, Outdoor Tools - Olight Official Store- Olight

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>