DunRock DAFlvZD10HU Bubble Wireless Earbuds Instruction Manual

DunRock DAFlvZD10HU Bubble Wireless Earbuds

Product Information

The DunRock Bubble is a pair of wireless earbuds that come with a charging case. It features LED lights and microphones for easy control and communication. The earbuds are available in two sizes, S and L, to ensure a comfortable fit for different users.

Product Usage Instructions

Connecting to a Device

1. For the initial setup, open the charging case, take out the earbuds, and place them back into the case. Close the case.
2. Open the charging case and take out the earbuds. The earbuds will attempt to connect.
3. On your phone, go to the Bluetooth settings and select “DunRock Bubble”. Choose “Connect” and then “Allow”.

To connect to another device:

1. Place the earbuds back into the charging case.
2. Open the case and press and hold the button for 3 seconds until the LED light on the case and/or earbud turns on.
3. On your phone, laptop, or other Bluetooth device, go to the settings and select “DunRock Bubble” to connect.

Resetting the Earbuds

1. Remove the DunRock Bubble from your previously connected devices (phone, laptop, tablet).
2. Press the earbuds into the case, close and open the lid.
3. Press and hold the button on the case for 10 seconds until the LED lights on the earbuds blink red 5 times. Keep holding until the process is complete.
4. Take the earbuds out of the case, and they will be ready to connect again.

Using the Earbuds

Power On/Off:

• To turn on the earbuds, take them out of the case or touch them for 2 seconds.
• To turn off the earbuds, place them back into the case and close the lid.

Volume Control:

• To increase the volume, press the right earbud once.
• To decrease the volume, press the left earbud once.

Switching Modes:

• Press and hold the right earbud for 2 seconds to switch between noise cancelling, transparency, and normal modes.

Playback Control:

• To play or pause, press the right earbud twice.
• To skip to the next song, press the right earbud three times.
• To answer a call, press the right earbud twice. To reject a call, press and hold the right earbud. Press twice to end a call.
• To activate voice assistance, press the left earbud three times.
• To enable game mode, press and hold the left earbud for 1.5 seconds.

Wearing the Earbuds
Ensure that the stem of the earbud is positioned close to your jaw/face. The earbud should not protrude outward too much as it may affect sound transmission. Adjust the earbuds slightly until they fit securely in your ear, ensuring optimal sound quality, bass, and noise cancelling.

Rotate the earbuds slightly until they provide the best seal in your ear. This is essential for optimal sound quality, bass response, and noise cancellation.

Troubleshooting

Problem: The earbuds do not connect to my phone or laptop.
Solution: Charge the case and earbuds. Reconnect. If it still doesn’t work, check if they are connected to another device. If not, perform a reset and try again.
Problem: The earbuds do not disconnect in the charging case.
Solution: This is usually due to an empty charging case. Charge the case with the earbuds inside to disconnect them.
Problem: I want more bass.
Solution: Increase the volume sufficiently to hear all tones clearly. Disable device equalizers and ensure that the earbuds fit snugly in your ear. The stem of the earbud should be positioned close to your cheek, without pointing outward at the bottom.
Problem: I can’t hear my own voice clearly during calls.
Solution: Enable transparency mode before making a call. This will amplify your own voice in your ear.
Problem: The earbuds stutter or the connection drops.
Solution: Check if the issue is caused by your device (restart, update, improve internet connection). Strong signals from other sources such as trams, buildings, stations, microwaves, refrigerators, etc., can also cause interruptions. As a final check, perform a reset and try again.

Included

Connect

• Only the first time: Open the box, take out the earbuds, and place them back in the case. Close the box.
  1. Open the charging case and remove the earbuds from the case. The earbuds will now try to connect.
  2. Go to the Bluetooth settings on your phone and select DunRock Bubble > connect.
• Want to connect with another device?
  • Place the earbuds in the charging case, open the box, and press the button for 3 seconds until the light on the case and/or earbud is on.
  • Then, on your phone, laptop, or other Bluetooth device, select DunRock Bubble in the settings and connect.

Earbuds can connect to one device. Not to two devices.

Reset

1. Remove the DunRock Bubble from your phone, laptop, and tablet (if they were ever connected).
2. Place earbuds in the case, close and open the lid.
3. Press the button on the case for 10 seconds (LED lights on the earbuds will flash red 5 times). Keep it pressed until completed.
4. Take the earbuds out of the case, and you can now connect the earbuds.

Opladen

Charge case
Place the cable in the charging case. A red light on the case indicates: charging. A white light on the charging case indicates: the case is full.

Charging earbuds
Put the earbuds in the charging case. A red light indicates that the earbud is being charged. A white light indicates that the earbud is fully charged.

Controls

Press and hold right earbud for 2 sec. to switch between noise cancelling, transparency, and normal mode.

You have an incoming call. Press twice to answer or press and hold to reject. Press twice to end the call.

• ON:   take out earbuds or touch 2 sec.
• OFF :earbuds in case  + close lid*
• volume higher: press 1x right
• volume lower: press 1x left
• play/pauze: press 2x right
• next track: press 3x right
• play/pauze: press 2x left
• voice assist: press 3x left
• game mode: left 1,5 sec press and hold
• Can’t disconnect? Charge the case while earbuds are in the case.

Problem? Solution.

• The earbuds are not connecting to phone or laptop. Charge the charging case and earbuds. Reconnect them. If it doesn’t work, check if they are not connected to another device. If not, reset and try again.
• The earbuds do not disconnect in the charging case. The problem is always that the charging case is empty. Charge the charging case when the earbuds are inside. They will disconnect when while charging in the case.
• I want to hear more bass. Set the volume loud enough to hear all tones clearly. Make sure device equalizers are turned off and ensure a proper seal of the earbuds in your ears. The stem of the earbud should be closely along your cheek at the bottom. It should not point outward at the bottom.
• The microphone is not working properly. Verify if the issue is indeed related to the microphone. Record a short snippet and check if you hear yourself clearly. If you’re not clearly audible, clean the openings.
• I cannot hear my own voice well during phone calls. Enable the transparency mode before making a call. This will amplify your own voice in your ear, allowing you to hear your own voice better while speaking.
• The earbuds connection keeps dropping. Verify if the issue is caused by the device by restarting it, updating its software, and improving the internet connection. Audio interruptions can also be caused by strong other signals like buildings, stations, microwaves. As a final check, perform a reset and try again.

Question? Answer.

• What is active noise cancelling?
  Active noise cancelling reduces ambient noise, allowing you to hear less of your surroundings. It particularly filters out low-frequency sounds. Test the noise cancelling feature in environments with predominantly high ambient noise, such as on an airplane or train.

• What is transparency mode?
  Transparency mode actively plays the ambient sound through your earbuds. It’s useful when you want to hear the sounds around you while using your in-ear earbuds.

• These earbuds have ENC mics. What is ENC?
  ENC stands for environmental noise cancelling. It reduces the impact of your environmental noise for the person you are speaking to during calls. However, ENC is not effective at filtering out hard wind noise, as microphones are sensitive to wind interference.

• What is Game Mode?
  Game Mode minimizes audio-visual delay, ensuring synchronization between the sound and visuals. This is useful when watching videos or playing games.

• How do I ensure the best sound?
  Make sure the earbuds fit properly in your ears, considering the position of the earbud and using the right-sized eartips. Select the best codec in your settings Bluetooth > DunRock Bubble > choose AAC. Opt for the highest quality in your music app. Disable any form of equalizer in your phone and music app. Also, make sure the bottom of the earbud sits close to your cheek.

Don’t

• Avoid damaging or potentially hazardous situations: do not disassemble your earbuds.
• Avoid extreme temperatures for the earbuds (below 0°C and above 45°C).
• Avoid shining the lights near the eyes of children or animals.
• Avoid using earbuds in situations where being aware of ambient noise can contribute to your safety.
• Do not use the earbuds during a thunderstorm to prevent interference and reduce the risk of electric shock.
• Do not use aggressive chemicals or strong cleaning agents when cleaning this product.
• Do not use the earbuds for an extended period and/or at high volumes, as it can damage your hearing.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>