P36x Tree Punk PulleyOne User Guide

P36x Tree Punk Pulley One

Markings & Nomenclature

a UKCA 0321 -Approved Body No.
b CE 2777 – Notified Body No.
c ENl 2278:07 – European Standards
d MBS 36kN – Minimum Breaking Strength
e Y’fXXZ?2ZZ- Individual Serial Number
f  011.5mm – Rope Diameter
g Product Code
h – Read User Instructions Manual
i Patent Pending- No. 2205034.8
j Product Logo
k Brand Logos
I Manufacturers Website & Address
m Connection Aperture
n Frame Cut-out’s to Ease Karabiner Installation/ Removal

Loading The PulleyOne

Section Two

“Recommended Connectors in Section Five

Using The PulleyOne

Section Three

Misusing The PulleyOne

Section Four

Prefe1Ted Connectors

Section Five

Suggested Configuration

Section Six

Product Inspection Record Card Example

Date| OK?

(If no, report defects here)

| Name & Signature| Date of Next Examination
---|---|---|---
Product Type and Identification Number| Year of Manufacture| Year of Purchase| Date of First Use
---|---|---|---

PulleyOne

Warning!
Working at height and related activities are inherently dangerous. It is the responsibility of any person using this equipment to learn, understand and practice the proper techniques for use of the equipment for its designated purposes. It is impossible forth is document to cover every eventuality and inco1Tect use of this equipment may result in fatal consequences. This equipment should only be used by the user and others specifically trained  in its use. This equipment should not be used by persons with medical conditions that may affect the safety of the user.

You are responsible for your own actions and any person using this equipment assumes all risks and full responsibility for all damages or injury which may result from the use of it.
If this product is resold outside the original country of destination the reseller should provide these instructions for use in the language of the country in which the product is sold.

General Use
This PulleyOne is a modular pulley without swing-cheek plates used individually, oars part of a system, to create mechanical advantage in a hauling system. Multiple PulleyOne devices can be used on a single karabiner or sling. Ensure to attach the connector vertically through the connection aperture.

Inspection
The whole device should be checked by visual inspection on a regular basis (in line with the PPE Rags or more frequently if local regulations require it) and ensure that all marked text is legible.
All thorough examinations should be recorded on an equipment record card.

Loading The PulleyOne

1. Ensure the rope is secured underneath the pulley plate protrusions.
2. Use a second karabiner / sling in the lower portion of the connection aperture if required.
3. Stack two devices together and load the connector through the connection aperture of each device.
   Note: The working line can be introduced/ removed before installing/ removing the method of connection from its point of anchorage. The PulleyOne can also be introduced/ removed in a hauling system, where appropriate.

Loading The PulleyOne

1. Ensure the rope is secured underneath the pulley plate protrusions.
2. Use a second karabiner / sling in the lower portion of the connection aperture if required.
3. Stack two devices together and load the connector through the connection aperture of each device.
   Note: The working line can be introduced/ removed before installing/ removing the method of connection from its point of anchorage. The PulleyOne can also be introduced/ removed in a valuing system, where appropriate.

Loading The PulleyOne

1. Ensure the rope is secured underneath the pulley plate protrusions.
2. Use a second karabiner / sling in the lower portion of the connection aperture if required.
3. Stack two devices together and load the connector through the connection aperture of each device.
   Note: The working line can be introduced/ removed before installing/ removing the method of connection from its point of anchorage. The PulleyOne can also be introduced/ removed in a hauling system, where appropriate.

Prefe1Ted Connectors

1. Oval
2. 0ffset0val
   It is the responsibility of the person using the equipment to use a suitable method of connection.

Cleaning, Storage and Transport

This equipment must not be marked, modified or repaired by the user.

Note: This equipment is not user maintainable with the exception of the following:

Cleaning: if required clean with a mild household detergent and rinse in clean water. Thoroughly rinse and dry naturally in a warm ventilated room away from direct heat. Important: Cleaning is recommended after every use in a marine environment.

Cleaning: if required clean with a mild household detergent and rinse in clean water. Thoroughly rinse and dry naturally in a warm ventilated room away from direct heat. Important: Cleaning is recommended after every use in a marine environment.

Lifespan
This is the maximum life of the product, subject to detailed conditions, that the Manufacturer recommends that the product should remain in service. Metal Products- Indefinite. This may be as little as a single use, (or even earlier if damaged e.g. in transit or storage prior to first use) when considering the following criteria: fall arrest, general wear, chemical contamination, corrosion, mechanical malfunction/ deformation, cracks, loose rivets, heat contamination (over normal climatic conditions), clear and readable marking (e.g. marking, batch reference, individual serial numbers etc).

Declaration of Conformity

At Height Ltd declares that the products described above conform to PPE Regulation EU 2016/425 for EU and is subject to Module C2 under the supervision of Notified Body SATRA Technology Europe Ltd (NB 2777) Brace town Business Park,
Clone,
Co. Math,
Dl5YN2P

SATRA Technology Europe (NB2777) also performed the EU type examination (Module B)

according to applicable standard EN12278:07

and issued EU type examination certificates which can be found on the product page at www.atheightuk.com.

At Height declares that the products described above conform to PPE Regulation 2016/ 425 as amended to apply in GB for UKCA and is subject to Module C2 under the supervision of approved body

SATRA Technology Centre (AB 0321), Wyndham Way, Telford Way, Kettering, Northampton shire, NN16 BSD, UK

and issued UKCA certificates which can be found on the product page at www.atheightuk.com

CUSTOMER SUPPORT

At Height Ltd
47c Underback Old Road,
Holmfirth, HD91AS
United Kingdom

Designed & Developed by
Jammy. Design
hello@jammydesign.co.uk
Manufactured & Distributed by
At Height UK
info@atheightuk.com
Patent Pending No. 2205034.8

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>